SEALEY AP3503TB.V2 Drawer Mid Box Chest Instruction Manual
- June 21, 2024
- SEALEY
Table of Contents
3 DRAWER MID-BOX CHEST, 5 DRAWER
TOPCHEST, ROLLCAB 8 DRAWER WITH BALL
BEARING SLIDES – BLACK/GREY
MODEL NO’S: AP3503TB.V2,
AP3505TB.V2, AP3508TB.V2
AP3503TB.V2 Drawer Mid Box Chest
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to instruction manual
SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop
practice regulations are adhered to when using this toolbox combination.
Locate the toolbox combination
in a suitable working area.
Use on level and solid ground,
preferably concrete.
Keep the work area clean,
uncluttered and ensure that there is adequate lighting.
Keep the toolbox combination
clean and tidy in accordance with good workshop practice.
Keep children and unauthorised
persons away from the working area.
DO NOT use the toolbox combination for any purpose other than that for which
it is designed.
DO NOT move the toolbox combination with drawers open. To avoid tipping, open
one drawer at a time and close and secure all drawers whilst moving.
DO NOT overload or step on the drawers.
DO NOT place the toolbox combination in a damp or wet location or an area
where there is condensation.
DO NOT clean the toolbox combination with any solvents which may damage the
surfaces or the protective coating.
WARNING! The warnings, cautions and instructions referred to in these
instructions cannot cover all possible conditions and situations that may
occur. It must be understood that common sense and caution are factors which
cannot be built into this product, but must be applied by the operator.
INTRODUCTION
Manufactured with double skin side walls for extra strength and finished in smooth, hi-gloss, triple baked enamel. Resists scratches, oil, dirt and most solvents. Smooth ball bearing drawer slides provide superior performance and carry heavier loads. For mobility around the workshop, even when fully laden, the rollcab features hard compound rubber wheels, two fixed and two locking castors. All drawers have been specifically sized to accommodate our range of Siegen tool trays. Supplied with two keys.
SPECIFICATION
Model No: ………………………………………………..AP3503TB.V2
W x D x H:
Overall Size:…………………………………….. 605 x 310 x 275mm
Small drawers (3x): ……………………… 508 x 268 x 54mm mm
Model No:…………………………………………………AP3505TB.V2
Overall Size:………………………………. 625 x 305 x 470mm mm
Small Drawers (5x):…………………………….. 508 x 268 x 54mm
Model No:…………………………………………………AP3508TB.V2
Overall Size:…………………………………….. 615 x 330 x 885mm
Overall Size inc. Handle: ……………………. 680 x 330 x 885mm
Small Drawer (5x): ……………………………… 508 x 268 x 54mm
Large Drawer (x3): ……………………………… 508 x 268 x 91mm
ASSEMBLY & INSTALLATION
4.1. These units are heavy, obtain the help of at least one other person
before attempting to unpack and move them.
4.2. Attach the wheels to the bottom of the rollcab using 4 bolts and
washers per wheel. The braked swivel wheels should be mounted on the same end
as the side mounted handle (left hand side, fig.1).
4.3. Mount the side mounted handle onto the cabinet and attach with 4
bolts and washers (fig.3).
4.4. To remove a drawer with roller sliders, pull the drawer out
completely, press down the left tab and lift up the right tab, pull the drawer
off the slides (fig.2). To reinstall the drawer, realign with the internal
drawer slide and push until it locks in place.
IMPORTANT: To avoid tipping, open one drawer at a time and close and
secure all drawers whilst moving the topchest/rollcab.
MAINTENANCE
5.1. Periodically lubricate castors and tighten all hardware.
5.2. Clean the surfaces with a soft cloth and a mild water/detergent
solution.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice. Please note that other versions of this product are available.
If you require documentation for alternative versions, please email or call
our technical team on technical@sealey.co.uk
or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
01284 703534
sales@sealey.co.uk
www.sealey.co.uk
© Jack Sealey Limited
Original Language Version
AP3503TB.V2, AP3505TB.V2, AP3508TB.V2
Issue: 1 (14/01/22)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>