TWO TREES TTC450 Pro CNC Router Machine Instruction Manual
- June 21, 2024
- TWO TREES
Table of Contents
TWO TREES TTC450 Pro CNC Router Machine
Product Information
- Specifications
- Model: PSFBCVOEBOU&BTJFS4USPOHFS4NBSUFS
- Power: 55$1SP$/$3PVUFS
- Weight: 5&-
- Dimensions: 130%6$5./6-
The versatile product is designed for various applications. With a power rating of this product offers reliable performance in a compact and lightweight design.
Product Usage Instructions
- Warnings
- Prevent hand injuries during use.
- Take precautions to avoid dust accumulation.
- General Usage
- Ensure proper ventilation during operation.
- Refer to the user manual for detailed instructions on specific functions.
- Keep the product clean and dry when not in use.
- Maintenance
- Regularly clean the product using a soft cloth and mild detergent. Avoid using harsh chemicals that may damage the product’s surface.
- Storage
- Store the product in a cool, dry place away from direct sunlight and moisture.
To our customers
Dear Customer:
- To ensure that you can assemble and use it smoothly, we have prepared this assembly and used a guide instruction manual. Please read the following content carefully and operate according to the instructions to ensure safety and convenience when using.
- If you encounter any problems during use, you can scan the QR code, company address and USB flash drive information to obtain the relevant instructions and videos. When the machine breaks down, please refer to the name of the corresponding part in the machine, and contact us with the problem and machine condition according to the after-sale e-mail provided on this page.
- After-sales Email: service@twotrees3d.com.
- Inquiry Email: info@twotrees3d.com.
Safety Warning:
- When using the machine for the first time, please make sure that the machine installation is firm.
- When danger occurs, press the emergency stop button quickly.
- Wear safety glasses when operating the machine.
- Please use a brush to remove debris, do not blow with your mouth.
- Be careful with sharpness when using Milling tools or sanding workpieces.
- Install Milling tools, and make sure it is solid.
- When loading and unloading, setting knife, measuring and cleaning, please make sure that the machine must be stopped before operation.
- Do not wear cotton gloves during the operation.
- Do not place measuring tools or other sundries within the scope of the workbench.
- Clamp the workpiece firmly, do not start engraving when it cannot be loosened or not clamped.
Parts List
Know Your Engraving Machine
460x460x80mm working space, creating more possibilities to meet most daily needs
- Z-axis motor
- T8-4 Screw
- 775 spindle motor
- 4080U side profile
- Sheet metal side panel
- USB interface
- TF card slot
- Emergency stop switch
- 1535 touch screen
- Engraving platform
- M5 Calibration screw
- X-axis motor
- Y-axis Limit switch
- X-axis Limit switch trigger
- Z-axis Limit switch
- M6 fixed hole
- Clamp
- Rubber feet
- X-axis support plate
- Y-axis motor
Know Your Engraving Machine
- DC power interface
- 500W spindle input
- 500W spindle output
- Z-axis Limit signal input
- X-axis Limit signal input
- Probe signal input
- 775 Spindle motor output
- Z-axis motor output
- Power input port (M)
- Signal output port (S)
- Laser output (PWM)
- Air pump output
- X-axis Limit switch
- 24V Switch
- 24V Output
- 24V Triggering signal
- A-axis
- Antenna
Set up TTC450 Pro
- Step 1: Installing X-axis components
- Required parts
- X-axis components
- M5X8 screw *6
- 3.0 hexagonal wrench
- 4.0 hexagonal wrench
- Step 2: Assemble the Z-axis and connect the cables
- Assembled in numerical order.
- Required parts
- Z-axis components
- Cable Tie Mount*2
- M3X16 screw *2
- Cup head M5X20 screws *4
- 2.0 hexagonal wrench
- 4.0 hexagonal wrench
- Step 3: Installation of TS35 Touch Panel
- Required parts
- TS35 touch screen kit*1
- 2.0 hexagonal wrench
- Wifi antenna*1
- Step 4: Installation of the motor housing base and access to the power supply
- Required parts
- Power adapter*1
- Power cable*1
- M5X8 screw*4
- Step 5: 775 motor chuck installation
- Required parts
- 775 spindle motor*1
- 775 motor chuck*1
- 3.0 hexagonal wrench
- 4.0 hexagonal wrench
- M5X12 screw*2
- Cup head M5X12 screw*2
- Step 6: Test
- Make sure the emergency stop switch is popped up, and plug in the power. If the screen lights up, the power on is normal. If the screen does not light up, after power off, exchange the screen line position to reboot.
- Click the “Control” button and move the XY-axis to the bottom left corner of the machine.
- Click XY Clear and Z Clear Then move the XY axis away from the corner.
- Click “NEXT”, and click “Home” to return to the corner.XYZ axis will return to the bottom left corner of the machine.
- Click “Spindle” to rotate the spindle. Click “Spindle” again to stop the spindle.
Operation Guide
- Step 1: Installation of milling cutter
- Note: The clamping length of the cutter is approximately 1/2 or 1/3 of the total length of the cutter.
- Step 2: Fixture installation
- The workpiece is clamped by adjusting the butterfly nut.
- Note: The tool path bypasses the fixture to avoid collisions.
- Step 3: Get familiar with the operation interface
- Connection status display.
- Step 4: Function switch
- Step 5: Setting the origin of the coordinates
- Step 6: Select File Engraving
FAQs
- Motherboard
- Q1: The motor or limit switch not working.
- A1: Please confirm that the motherboard wiring is correct, as shown in Figure 1, in the case of correct installation, ensure that the wiring is not loose.
- Power supply
- Q1: No response after power-on.
- A1: Pls check if the cable is loose and plug it in again.
- A2: Check if there is voltage at the power socket interface, and if there is current at the power input. If the former does not have the latter, it is a problem with the power supply.
- A3: Check if the power socket is loose and the power indicator is on. Please check if the power indicator of the chassis is on. If the light is on but the machine is not working properly, check whether the indicator light on the motherboard is on. If it is not lit, the output power cable is loose, or the motherboard has a problem.
- Screen
- Q1: When the screen does not show.
- A1: As shown in the figure -2. Pls check if the screen cable is loose and re-tighten, Or change the line sequence restart.
- A2: The screen line is loose: There will be a vibration during the transportation of the machine. The vibration may cause the wire plug inside the machine to loosen and cause poor contact or no contact. At this time, the screen of the machine will turn white and not work properly. Pls, check if the line has problems first.
- A3: Motherboard or screen problem: If there is no problem with the screen line, then there is a problem with the motherboard or the screen. If there are multiple machines, you can replace the “bad” with a normally displayed screen. if the good screen can be displayed normally, it is a problem with the original screen, if not, there is a problem with the motherboard. If you encounter this problem, you can contact the after-sales customer service.
- Clearance adjustment
- We have reserved enough space for adjusting the lead screw. If you feel a slightly noticeable gap in the screw travel after using it for a while please don’t worry, this is caused by the wear of the brass nut or the loosening of the screw. As shown in the figure-3. The solution is as follows:
- Remove the sheet metal on the side.
- Loosen the screws and tighten them again to solve the problem.XYZ axis adjustment method is the same.
- Motor
- Q1: If the motor has a jitter fault, or there is no response after plugging in the power.
- A1: ite wheres or poor come, he more can he the mere pure port are firmly connected.
- 42: Exchang none a sits of the extent them response per rer eling After the st, the moor Fault is judged. (A. Motor line Problem B. Drive problem C. Motor problem).
- A3: Motor line problem: After confirming that the motor is ok, please exchange positions of the problematic line on the main board and the motor with the motor line that has no problem, and then test it. If there is no problem, then it is the problem of the motor line. If it still doesn’t work, pls check the driver.
- A4: Nothing he hammer lie and the good more. in hot this more ine are ay is it’s A your same time, it is necessary to match the motor line to the corresponding motor. After power-on, test it by testing the function of the moving shaft.
- A5: Drive problem: Under the premise of confirming that the motor and the motor line are no problem, check the motor drive again. There may be a problem with the drive and a new drive needs to be replaced.
- Motherboard
- Q1: Motherboard does not read cards.
- A1: TF card problem: How to determine if there is any problem with the TF card, first check whether the card can be used normally on the computer. If the TF card can be used normally on the computer, first save the file to the computer and format the card at the same time. After the card is put on the machine and tested, if it is not recognized after the power-on test, it proves that the TF card has a problem and needs to be replaced.
- A2: Check if the card slot is loose. Long-term use of the card slot may cause the cardholder to shake, resulting in poor card reading, and the need to replace the new cardholder to solve the problem. Sometimes the card may be inserted into the card for a moment and then suddenly no response. You can quickly plug in and out several times and then try to plug in after turning off the power, then take some alcohol to clean it on the card, then insert the card into the card slot, and then insert it several times to see if it can be used normally after cleaning.
- 43: Tara slot, in ordination, ore times, see it an ite use normaly after cred, then insert the card into the card slot, insert a few more times, and see if it can be used normally after cleaning.
- Engraving problem
- Q1: Carved split level.
- A1: The drive heat sink is not attached – paste the heat sink to the drive.
- A2: Motor drive overheating – keep the drive’s heat dissipation good.
- A3: The motor drive current is too large – readjust the appropriate drive current.
- A4: Motor coupling loose-retighten the coupling.
- A5: POM wheel and Screw stuck – Manually adjust to a smooth position after oiling.
- Q2: The X Y Z axis direction cannot be reset.
- A1: Limit switch failure – replace the limit switch.
- A3: Come are motion speed is too savin motor drive – wise sexing i encorrect, drive jumper error.
- Q3: The engraving file is not recognized.
- A1: The TF file cannot be recognized after the TF card is inserted – the file code is incorrect and the code needs to be renamed.
- A2: Stop engraving after half of the engrave-programming problem or poor TF card contact.
- Q4: Engraving abnormal sound.
- A1: Fan problem – there may be abnormal noise caused by the fan blade touching the cable.
- A2: Structural problems – abnormal operation of the screw and POM wheel causes the sound to be too loud, re-oiling and correcting the direction. and cleaning up 4080 profiles.
- A3: Programming problem with the engraving speed, Decrease XYZ axis feed rate, Increase spindle speed.
- Q5: The computer cannot control the machine
- A1: The computer does not recognize the port and needs to install the USB driver.
- A2: The port of the computer connected to the machine cannot be controlled – Conflict between screen control and computer control, reboot.
After-Sales Service
The guarantee period is 12 months from the date of purchase.
- Missing/Damaged/DefeetiveParts Within 7 days of the date of receipt, we will replace any parts free of charge including shipping fees. After 7 days of the date of receipt, we will replace any parts for free of charge. But you need to pay the shipping fees.
- Customer Damaged Parts: You need to pay for the cost of the parts and the shipping fees.
- Courier company lost, missing, damaged, and defective parts.
- a. Lost or damaged shipments must be reported to the carrier within the carrier’s claim window, and you need to inform us within 7 days of the date of receipt.
- b. For any parts lost or damaged during shipping, you need to take photos or videos and send them to us.
- c. Once the Carrier dispute is settled, please provide us with all communications with the carrier. It is the
- d. For Miss’s Parts, you need to I out Service TickeL communication with the carrier.
- e. For Damaged Parts, you need to fill out a Service Ticket and send us the photos or video.
CONTACT
- TEL: +0086-0755-23987110
- Http: www.twotrees3d.com.
- E-mail: service@twotrees3d.com.
- Facebook: https://www.facebook.com/twotrees3d.
- Address: Room 402, Building 11, No.9 Oilin Road, Nankeng Community,
- Bantian Street, Longgang District, Shenzhen, Guangdong, China, 518000
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>