TWO TREES TTS-55PRO Laser Engraver Instruction Manual

June 15, 2024
TWO TREES

TWO TREES TTS-55PRO Laser Engraver Instruction Manual

TWO TREES TTS-55PRO Laser Engraver Instruction Manual

LETTER FROM TWOTREES

Dear Customers,
Thank you for choosing us.
It’s customer-oriented idea, continuous innovation and pursuit of excellence that enable everybody to have wonderful experience in using process.
We believe that this manual will be helpful.
Hope you enjoy the good time with Two Trees.
If you have any problems, please feel free to contact us via:
Website: www.twotrees3d.com
Facebook: https://www.facebook.com/twotrees3d
For general inquiry: info@twotrees3d.com
For technical support: service@twotrees3d.com
We will contact you within 24 hours.
Two Trees Team

SAFETY GUIDELINES
Warning:
Laser engraving machine cannot directly carve or cut material that reflects the light, may cause injury.
The product has a high engraving speed and is not recommended for industrial cutting. And the laser head is consumable.
Do not operate the laser head directly with your hands . Please wear goggles.
The laser diode is a sensitive component, please prevent static damage.
(This product has an electrostatic protection design. but there is still a possibility of damage).
We do not assume any responsibility for any improper use of this equipment or any damage or damage caused by improper use. The operator is obligated to use this laser engraving machine only in accordance with its designated purpose, instructions in its manual, and relevant requirements and regulations.

PRECAUTIONS

TWO TREES TTS-55PRO Laser Engraver Instruction Manual -
Precautions

ABOUT YOUR MACHINE

TWO TREES TTS-55PRO Laser Engraver Instruction Manual - About your
machine

MAIN PARAMETERS

TWO TREES TTS-55PRO Laser Engraver Instruction Manual - MAIN
PARAMETERS

ASSEMBLING THE MACHINE

Installation of master control box

TWO TREES TTS-55PRO Laser Engraver Instruction Manual - Installation of
master control box

Istallation of bellows mounts

TWO TREES TTS-55PRO Laser Engraver Instruction Manual - Installation M3 X
20

ASSEMBLING THE MACHINE

Installation of X-axis End Stop

TWO TREES TTS-55PRO Laser Engraver Instruction Manual - Installation of x
axis end stop

Installation Laser Modul

TWO TREES TTS-55PRO Laser Engraver Instruction Manual - Installation Laser
Modul

SET UP TTS-20 PRO

Bellows fixing

TWO TREES TTS-55PRO Laser Engraver Instruction Manual - Bellows
fixing

Adjustment of X-axis parallelism

TWO TREES TTS-55PRO Laser Engraver Instruction Manual - Adjustment of X-axis
parallelism

Adjustment of timing belt

TWO TREES TTS-55PRO Laser Engraver Instruction Manual - Adjustment of timing
belt

Side timing belt adjustment:
Lock the timing belt fixing screws on one side, pull the timing belt tight on the other side and then lock the side screws.
X-axis timing belt adjustment:
Check that the timing belt is hung on the X-axis motor

Adjust the focus

TWO TREES TTS-55PRO Laser Engraver Instruction Manual - Adjust the
focus

MACHINE WIRING

TWO TREES TTS-55PRO Laser Engraver Instruction Manual - MACHINE
WIRING

⚠ After the wire is connected, please try to push the machine to move and check whether the wire will interfere with the movement of the machine.

HONEYCOMB PANEL INTRODUCTION

The method of using honeycomb needle

Four honeycomb pins are fixed in the corner of the carved material to ensure that the material will not buckle.
Note: stainless steel will be deformed by heat, the honeycomb needle can not be fixed steadily

Stick non-slip sheets to the aluminium sheet First confirm the position of the paste anti-slip sheet with honeycomb board, and then paste the anti- slip sheet (honeycomb board corner protection may interfere with the attention to avoid position)

External auxiliary accessories can be added (included only in some packs)TWO TREES TTS-55PRO Laser Engraver Instruction Manual - External
auxiliary accessories can be added

MEET YOUR TTS-20 PRO

Machine Introduction

TWO TREES TTS-55PRO Laser Engraver Instruction Manual - Machine
Introduction

Motherboard Introduction

TWO TREES TTS-55PRO Laser Engraver Instruction Manual - Motherboard
Introduction

HOW TO START ?

TWO TREES TTS-55PRO Laser Engraver Instruction Manual - HOW TO
START

Engraving Learning Process

Learn to use LaserGRBL or lightburn.on websites
Learn to focus laser via manual or video
Test speed and power (Results for different materials)
Communicate and share via Facebook and YouTube

CONNECT PC

  1. Connect the machine with the computer installed with LaserGRBL software with USB data cable.
  2. Plug in the power.
  3. Open LaserGRBL on the computer.
  4. Select the specific port number and baud rate—-115200 (Figure A.10)
  5. Click the lightning sign. When the lightning sign changes to the red “X” and the direction sign is lit, it indicates that the connection is successful. (Figure A.11) Generally, the COM port does not need to be selected manually, unless multiple serial port devices are connected to the computer, you can find the port of the machine in the device manager of the windows system (as shown in Figure A.09). A simpler way is to try the displayed port number one by one.

TWO TREES TTS-55PRO Laser Engraver Instruction Manual - CONNECT
PC

Note: If you cannot find the correct port in the “Ports”, you may need to Method 1: Click “Tools” in the menu to install CH340 driver (This function is not available in some software versions); Method 2: Copy the “CH340ser. Exe” file in the TF Card (USB flash disk) to the computer and install it.

GRBL INTRODUCTION

  1. Software Downloading
    LaserGRBL is one of the most popular DIY laser engraving software, which can be downloaded in LaserGRBL website http://lasergrbl.com/download/ (The installation package is also available on the TF card from the manufacturer or USB flash disk). Brief introduction: LaserGRBL is easy to use. However, LaserGRBL only supports Windows system (Win XP/Win 7/Win 8/XP/Win 10). For Mac users, you can also choose LightBurn, which is also an impressive engraving software, but it’s not free. And this software also supports Windows system. Note: The engraving machine needs to be connected with the computer during engraving, and the software of the engraving machine cannot be turned off.

  2. Software Installation
    Double click the software installation package to start the software installation and click “Next” until the installation is complete.

  3. Language
    Click “Language” on the menu at the top to select the language you need.TWO
TREES TTS-55PRO Laser Engraver Instruction Manual -
Language

  4. Load Engraving File
    Click “File” and “Open File” in turn, as shown in figure 8.1, and then select the graph you want to engrave. LaserGRBL supports files in the formats of NC, BMP, JPG, PNG, etc.

  5. Set picture parameters, engraving mode and engraving quality.

  6. Laser GRBL can adjust the sharpness, brightness, contrast, highlight and other properties of the target graph. We can preview window effect during adjustment, and adjust the effect to your satisfaction.

  7. In the engraving mode, “Line-to-line Tracking” and “1Bit Shaking” can
    usually be chosen;”1Bit Shaking” is more suitable for carving grayscale graph. Please Choose “Vector Diagram” or “Center Line” if you need cutting.

  8. Engraving quality essentially refers to the line width of laser scanning.
    This parameter mainly depends on the size of the laser spot of the engraving machine. Note: The recommended engraving quality range is 12-15. Different materials have different reactions to laser irradiation, so the specific value depends on the specific engraving material.

  9. At the bottom of the preview window, the graph can also be rotated,
    mirrored, cut and so on. After completing the above settings, click next to enter the settings of engraving speed, engraving energy, and engraving size.TWO TREES TTS-55PRO Laser Engraver Instruction Manual - Set picture
parameters

  10. Set engraving speed, engraving energy, and engraving size

  11. The recommended engraving speed is 1000, which is considered to be a relative appropriate value after repeated experiments. Of course, you can increase or decrease this speed according to your preference. A faster engraving speed will save time but lead to the decline in the engraving effect. Slower speed is the opposite.

  12. In laser mode, there are two instructions: M3 and M4. M4 instruction is recommended for engraving in “1bit jitter” mode, and M3 instruction is recommended for other cases. If you have only M3 instruction on the laser, please check whether the laser mode is used in the GRBL configuration.
    Please refer to the official instructions of LaserGRBL for GRBL configuration.

  13. Choice of engraving energy. Choose it according to different materials.

  14. Finally, set the size and click the “Create” button to complete the setting of all engraving parameters.

TWO TREES TTS-55PRO Laser Engraver Instruction Manual - Set engraving
speed

Save GCODE file
Click “File” in the menu at the top of the software interface, enter the drop- down menu, and select “Save”. Copy the saved .nc file to the TF card and insert the TF card into the engraver to use the file to engrave your work. Use the “MKSLaserTool” software in TF to add preview codes to Gcode files.

REFERENCE OF MATERIALS

TWO TREES TTS-55PRO Laser Engraver Instruction Manual - REFERENCE OF
MATERIALS

Note: The energy value is set to 500, and the laser intensity accounts for 50% of the power. The energy value is set to 1000, and the proportion of laser intensity to power is 100%. The larger the energy, the faster the speed can be set. The above parameters only for reference. Due to the different properties of the materials, please adjust the parameter values according to the actual situations. 16

TEST BEFORE USE

  1. Turn on the machine, and connect it to the computer.

  2. Movement test:
    Control the machine to move up, down, left and right on the software, to check whether the direction and distance are right.(Fig. A01)

  3. Laser emission test:
    Software import custom icons, then click to sent out laser(weak laser). Wear goggles and observe whether the laser module emits blue light.(Fig. A02)

  4. Test the files in the TF card:
    Note: laser will generate heat and glare, which may cause harm. Please follow the instructions to avoid injury.

TWO TREES TTS-55PRO Laser Engraver Instruction Manual - TEST BEFORE
USE

  1. After the laser head has been used for a period of time, it is necessary to clean the lens of the light outlet under the laser head to ensure normal cutting ability
  2. Wiping the lens must be done after the machine is powered off, otherwise the laser will hurt people
  3. After wiping the lens, please dry it naturally for about 3-5 minutes and wait for the lens to dry before powering it on, otherwise the light will cause the lens to break
  4. You can watch the video tutorial by scanning the QR code of the manual

APP CONNECTION

The WIFI of this machine is a signal sent by the ESP32 chip of the main board. The machine has been set up when the machine leaves the factory. After the machine is turned on, the main board will send out the WIFI network with the name Laser_XXXXX (XXXXX refers to the serial number of the main board, the serial number of each machine). all different)

  1. Open the Laser_XXXXX network found by the mobile phone connection, enter the password 12345678, and connect to the network.
  2. Open the APP and enter the connection options interface. Enter the IP address: 192.168.4.1 and click connect.
  3. After the APP slicing is completed, you need to insert the TF card into the motherboard when uploading files. If the upload fails, please confirm whether the TF card is normal.
    TWO TREES TTS-55PRO Laser Engraver Instruction Manual - APP main
interface

AFTER-SALES SERVICE

The guarantee period is 12 months from the date of purchase.

  1. Missing/Damaged/Defective Parts
    Within 7 days of the date of receipt, we will replace any parts for free of charge including shipping fees. After 7 days of the date of receipt, we will replace any parts for free of charge. But you need to pay the shipping fees.

  2. Customer Damaged Parts: You need to pay for the cost of the parts and
    the shipping fees.

  3. Courier company loss, missing, damaged, and defective parts.
    a. Lost or damaged shipments must be reported to the carrier within the carrier’s claim window, and you need to inform us within 7 days of the date of receipt.
    b. For any parts lost or damaged during shipping, you need to take photos or video and send them to us.
    c. Once the Carrier dispute is settled, please provide us with all communications with the carrier. It is the customer’s responsibility to keep us up to date with ALL communication with the carrier.
    d. For Missing Parts, you need to fill out a Service Ticket.
    e. For Damaged Parts, you need to fill out a Service Ticket and send us the photos or video.
    f. If the part is one of the LCD Panel, Power Supply or Mainboard, you need to ship the part back to us and we will send a new one.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals