TWO TREES TT-5.5S Totem S High Precision Engraving Machine User Manual

TWO TREES TT-5.5S Totem S High Precision Engraving Machine

The product user guide contains product features, how to use, and the operating procedure. Read the user manual carefully to get the best experience and avoid unnecessary damage. Keep this manual for future reference. If you have any questions or comments about the device, please contact the customer line.

Warning

ASER FOCUS REDUCES HEAT AND GLARE WHICH CAN HARM HUMANS, ANIMALS, AND OBJECTS. FOLLOW THE INSTRUCTIONS. MISUSE WILL BE AT YOUR OWN RISK.

• Avoid direct eye contact, may lead to blindness.
• Avoid exposure to the body surface, it burns.
• Put a base plate under the workpiece.
• Avoid using near combustible objects or gasses.
• Keep away from children, pregnant women, and the elderly.
• Do NOT take apart the laser without instructions.
• Do NOT use it on material that reflects light.
• Wear goggles while using the laser.
• Turn off the power when not in use.

Warning:
The laser engraving machine cannot directly act on any secularly reflective object. This can cause injury to the operator or burn the laser.

•  The product has a high engraving speed and is not recommended for industrial cutting. The laser head is a consumer good.
•  It is not recommended to look directly at the laser head when the machine is working. Also do not operate the laser head directly with your hands. Please wear goggles. Ensure that the engraving machine is safe, fireproof and away from any children’s environment.
• The laser diode is a sensitive component, please take care to prevent static damage.
• (This product includes an electrostatic protection design, but there is a possibility of damage).

Parts List

Know Your Engraving Machine

1.  Z-axis Fine-Tuning Module
2.  Laser Head
3.  Foot Pad
4.  Motherboard Fixed seat
5.  Tensioner
6. Y-Axis Motor
7. Y-Axis Right Injection Molded
8. Carriage Head
9.  Motherboard
10.  X-Axis Motor
11.  Y-Axis Left Injection Molded
12.  Y-Axis Motor

Install the Feet

Note:

1.  Install the T-nut and screw on the footpad, Place the T—nut to the corresponding profile
2. The smooth side of the profile is facing up

 Install the Feet

Install the Carriage Head

If it is difficult to push in, you can adjust the eccentric nut of the carriage head.

 Install the Left Support

T-nuts and screws have been fixed on the injection molded part T-Nut 20-M4 (2 Pcs) Half Round Head M4*10 (2 Pcs)

If the wheel is hovering and rotating, it does not fit the profile. The eccentric nut can be adjusted clockwise from the screw head with a wrench

 Install the Right Support

T-nuts and screws have been fixed on the injection molded part T-Nut 20-M4 (1 Pcs)Half Round Head M4*10 (1 Pcs)

If the wheel is hovering and rotating, it does not fit the profile. The eccentric nut can be adjusted clockwise from the screw head with a wrench

Install the Timing Belt

1. Put the timing belt on the pulley of the X-axis motor
2. The timing belt is set on the head of the carriage
3. Fix the tensioner with screws and T—nuts.
4.  The timing beltline is sleeved on the idler pulley, push it into the fixing seat and lock the screw, then screw the nut to install it

 Install the Lifting Platform

Install the Motherboard

M4*12 Screws (2 Pcs) T-Nut 20-M4 (2 Pcs)

 Laser Head Focusing

Using a fixed focus laser head, Control the focus of the laser head by adjusting the lift table, the fixed focus distance is 20mm

The distance is too far, the focus is not right, and the carving cannot be made Correct focus and clear carving

Wiring diagram

You can put a suction cup in the red box, and tie a cable tie to fix the wire

 Install non-slip gasket

You can stick a non-slip sheet under the footpad to stabilize the.

1. Open the GRBL software installation package of the SD card to install the software by default according to the steps, and the installation is complete as shown in the figure
2. Open the software and select the corresponding COM. Connect to 115200 baud rate, and then click ”Configure”, as shown
3. As shown in the figure, read the configuration file that comes with the tf card.
4.  Import successful. You can also modify the configuration properties if needed. For details, please refer to tf card and grbl code.
5. Right-click below the main interface and click the Import button to configure.
6. Click on this file to import.
7.  Click Open File to open the picture you need to sculpt.
8. Select the engraving method according to your needs.
9. Click NextThe laser is enabled with the M3 spindle CW or M4 spindle CCW commands. These enable two different laser modes that are advantageous for different reasons each. http://lasergrbl.com/usage/raster—image-import/target-image—size—and-laser-options
10.  Click Finish to return to the main interface, Control the sculpting head to the lower left, Click to set the origin and click the engraving range option, View the carving area.
11.  If the red font is displayed here, click the unlock button to unlock it.

Warranty Conditions

A new product purchased in the Alza.cz sales network is guaranteed for 2 years. If you need repair or other services during the warranty period, contact the product seller directly, you must provide the original proof of purchase with the date of purchase.
The following are considered to be a conflict with the warranty conditions, for which the claimed claim may not be recognized:

• Using the product for any purpose other than that for which the product is intended or failing to follow the instructions for maintenance, operation and service of the product.
•  Damage to the product by a natural disaster, the intervention of an unauthorized person or mechanically through the fault of the buyer (e.g. during transport, cleaning by inappropriate means, etc.).
• Natural wear and aging of consumables or components during use (such as batteries, etc.).
•  Exposure to adverse external influences, such as sunlight and other radiation or electromagnetic fields, fluid intrusion, object intrusion, mains overvoltage, electrostatic discharge voltage (including lightning), faulty supply or input voltage and inappropriate polarity of this voltage, chemical processes such as used power supplies, etc.
• If anyone has made modifications, modifications, alterations to the design or adaptation to change or extend the functions of the product compared to the purchased design or use of non-original components.

References

• Alza.cz – rychlý a pohodlný nákup odkudkoliv | Alza.cz
• Target Image Size and Options – LaserGRBL
• alza.at
• Alza | Alza.co.uk
• Alza.cz – rychlý a pohodlný nákup odkudkoliv | Alza.cz
• Alza.cz – rychlý a pohodlný nákup odkudkoliv | Alza.cz
• Alza.cz
• alza.de
• alza.sk

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>