metabo RWE 1020 Variable Speed Electric Mixer Instruction Manual

metabo RWE 1020 Variable Speed Electric Mixer

Product Information

The product is a set of power tools with the following models:
RWE 1020, RWEV 1200, RWEV 1200-2, RWEV 1600-2, and RW 18 LTX 120. The product is manufactured by Metabo and operates at an 18V voltage. The battery capacity options are 5.2Ah, 6.2Ah (Li-HD), and 7.0Ah (Li-HD). The product has different serial numbers for each model, which are 14044 for RWE 1020, 14045 for RWEV 1200, 14046 for RWEV 1200-2, 14047 for RWEV 1600-2, and 01163 for RW 18 LTX 120.

The product has different specifications for each model:

• RWE 1020:
  • Maximum speed: 900 min-1 (rpm)
  • Nominal speed: 700 min-1 (rpm)
  • Grinding wheel diameter: 120 mm (4 3/4 in)
• RWEV 1200:
  • Maximum speed: 590 min-1 (rpm)
  • Nominal speed: 580 min-1 (rpm)
  • Grinding wheel diameter: 140 mm (5 1/2 in)
• RWEV 1200-2:
  • Maximum speed: 520 min-1 (rpm) and 720 min-1 (rpm)
  • Nominal speed: 580 min-1 (rpm)
  • Grinding wheel diameter: 140 mm (5 1/2 in)
• RWEV 1600-2:
  • Maximum speed: 470 min-1 (rpm) and 680 min-1 (rpm)
  • Nominal speed: 660 min-1 (rpm)
  • Grinding wheel diameter: 160 mm (6 1/4 in)
• RW 18 LTX 120:
  • Maximum speed: 760 min-1 (rpm)
  • Nominal speed: none specified
  • Grinding wheel diameter: 120 mm (4 3/4 in)

Product Usage Instructions

To use the product, follow these instructions:

1. Ensure that the battery is charged before using the product.
2. Select the appropriate grinding wheel for the task at hand.
3. Insert the grinding wheel into the product’s spindle and tighten it securely.
4. Turn on the product by pressing the power button.
5. Use the product to grind or cut the material as needed.
6. After use, turn off the product and remove the grinding wheel.
7. Clean the product and store it in a safe place.

It is important to follow the manufacturer’s guidelines for safety and maintenance when using the product. Refer to the user manual for more information.

Declaration of Conformity

We, being solely responsible: Hereby declare that these stirrers, identified by type and serial number 1), meet all relevant requirements of directives 2) and standards *3). Technical documents.

2017-01-17, Bernd Fleischmann
Direktor Produktentstehung & Qualität (Vice President Product Engineering & Quality)
*4) Metabowerke GmbH – Metabo-Allee 1 – 72622 Nuertingen, Germany.

Specified Use

The stirrer is intended for stirring of powdery building materials such as mortar, plaster, and adhesive as well as solvent-free paints, lacquer, and similar substances. Do not use it for drilling. The user bears sole responsibility for any damage caused by inappropriate use. Generally accepted accident prevention regulations and the enclosed safety information must be observed.

General Safety Instructions

For your own protection and for the protection of your power tool, pay attention to all parts of the text that are marked with this symbol!

WARNING
Reading the operating instructions will reduce the risk of injury.

WARNING
Read all safety warnings and instructions. Failure to follow all safety warnings and instructions may result in electric shock, fire, and/or serious injury.

Keep all safety instructions and information for future reference.
Pass on your power tool only together with these documents.

Special Safety Instructions

the intended handles, take a secure stance and concentrate on the work. Loss of control can cause personal injury. Hold the power tool by the insulated gripping surfaces when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

Observe the maximum permitted agitator paddle diameter (see technical data). There will be reverse torque at the handle. Always hold the machine with both hands on the intended handles, take a secure stance and concentrate on the work. Secure the stirring container against turning.

Always wear protective goggles, gloves, and a breathing mask when working with the machine.
Wear ear protectors when working for long periods of time. High noise levels over a prolonged period of time may affect your hearing.

Keep hands away from the rotating tool!
Do not mix solvents or materials containing solvents with a flashpoint below 21°C. Hazardous vapours or explosive mixtures may form during processing.

Reducing dust exposure:
Some of the particles generated using this power tool may contain substances known to cause cancer, allergic reactions, respiratory diseases, birth defects or other reproductive harm. Some of these substances include: Lead (in paint containing lead), mineral dust (from bricks, concrete etc.), additives used for wood treatment (chromate, wood preservatives), some wood types (such as oak or beech dust), metals, asbestos. The risk from exposure to such substances will depend on how long the user or nearby persons are being exposed. Do not let particles enter the body.

Do the following to reduce exposure to these substances: Ensure good ventilation of the workplace and wear appropriate protective equipment, such as respirators able to filter microscopically small particles. Observe the relevant guidelines for your material, staff, application and place of application (e.g. occupational health and safety regulations, disposal). Collect the generated particles at the source, avoid deposits in the surrounding area. Use suitable accessories for special work. In this way, fewer particles enter the environment in an uncontrolled manner. Use a suitable extraction unit.

Reduce dust exposure with the following measures:

• Do not direct the escaping particles and the exhaust air stream at yourself or nearby persons or on dust deposits.
• Use an extraction unit and/or air purifiers.
• Ensure good ventilation of the workplace and keep it clean using a vacuum cleaner. Sweeping or blowing stirs up dust.
• Vacuum or wash protective clothing. Do not blow, beat or brush.

Special safety instructions for mains powered machines:
Pull the plug out of the socket before making any adjustments, changing tools, maintaining or cleaning.

Avoid unintentional starting:
Always unlock the trigger switch if the machine is unplugged or in the event of a power failure.

Special safety instructions for cordless machines:
Remove the battery pack from the machine before making any adjustments, changing tools, maintaining or cleaning.

• Protect battery packs from water and moisture!
• Do not expose battery packs to fire!
• Do not use faulty or deformed battery packs!
• Do not open battery packs!
• Do not touch contacts or short-circuit battery packs!
• A slightly acidic, flammable fluid may leak from defective Li-ion battery packs!
• If battery fluid leaks out and comes into contact with your skin, rinse immediately with plenty of water. If battery fluid leaks out and comes into contact with your eyes, wash them with clean water and seek medical attention immediately!

Transport of li-ion battery packs:
The shipping of li-ion battery pack is subject to laws related to the carriage of hazardous goods (UN 3480 and UN 3481). Inform yourself of the currently valid specifications when shipping li-ion battery packs. If necessary, consult your freight forwarder. Certified packaging is available from Metabo.

• Only send the battery pack if the housing is intact and no fluid is leaking. Remove the battery pack from the machine for sending. Prevent the contacts from short-circuiting (e.g. by protecting them with adhesive tape).

Overview

1. Spindle
2. Thumb-wheel for gear selection *
3. Trigger switch
4. Locking button for continuous activation
5. Speed preselection wheel *
6. Handles
7. Locking button
8. Battery pack release button *
9. Capacity indicator button *
10. Capacity and signal indicator *
11. Battery pack*
    • depending on the model/features

Commissioning

For mains powered machines only

• Before plugging in, check that the rated mains voltage and mains frequency, as stated on the rating label, match with your power supply.
• Always install an RCD with a maximum trip current of 30 mA upstream

For cordless machines only

Battery pack
Charge the battery pack before use (11).
If performance diminishes, recharge the battery pack.
The ideal storage temperature is between 10°C and 30°C.

“Li-Power, LiHD” lithium-ion battery packs have a capacity and signal indicator (10):

• Press the (9) button, the LEDs indicate the charge level.
• If one LED is flashing, the battery pack is almost flat and must be recharged.

Removing and inserting the battery pack

Remove:
Press the battery pack release button (8) and remove battery pack (11).

To insert:
Slide the battery pack (11) in until it engages.

Use

Tool change

Attach the stirrer:
Screw the stirrer by hand into the spindle (1).

Remove the tool:
Hold the spindle (1) using an open-ended wrench and fix the stirrer using a second open-ended wrench.

Select the gear (depending on features)
Select the required gear by rotating the thumb wheel (2).

Change speed when the machine is in the process of running down (briefly switch it on and off).

• I = 1. st gear (low speed, high torque)
• II = 2. nd gear (high speed)

Presetting the speed (depending on features)

• Select the maximum speed using the preselection wheel (5).
• (Press in the trigger (3) to increase the rotational speed.)

On/Off switch, modifying the speed
Switching on, speed: Press the trigger (3). Press in the trigger to increase the rotational speed.

To switch off release the trigger switch.

Continuous operation:
With the trigger (3) pressed, push in the locking button (4) and release the trigger. Press and release the trigger (3) again to switch off.

In continuous operation, the machine continues running if it is forced out of your hands. Therefore, always hold the machine with both hands using the handles provided, stand securely and concentrate.

Switching on/off, change speed (for cordless machines)

• Press locking button (7) and keep pressed, then press the trigger (3).
• Press the trigger (3) to increase the rotational speed.
• To switch off release the trigger switch.

Cleaning
Clean the machine regularly.

Troubleshooting

Mains powered machines:

• Overload protection: There is a MAJOR reduction in load speed. The motor temperature is too high! Allow the machine to run at idle speed until it has cooled down.
• Overload protection: There is a SLIGHT reduction in load speed. The machine is overloaded. Reduce the load before continuing to work.
• Restart protection: The machine does not start. The restart protection is active. If the mains plug is inserted with the machine switched on, or if the power supply is restored following an interruption, the machine does not start up. Switch the machine off and on again.

Cordless machines:
Overload protection: The machine has shut down by itself. The device is too hot! Allow the machine to run at idle speed until it has cooled down.

Accessories

Only use original Metabo battery packs and Metabo accessories. Battery packs with different capacities. Use battery packs only with a voltage suitable for your power tool. Use only accessories that fulfill the requirements and specifications listed in these operating instructions. See www.metabo.com or the catalog for a complete range of accessories.

Repairs
Repairs to electrical tools must ONLY be carried out by qualified electricians! Contact your local Metabo representative if you have Metabo power tools requiring repairs. See www.metabo.com for addresses. You can download a list of spare parts from www.metabo.com.

Environmental Protection

Observe national regulations on environmentally compatible disposal and on the recycling of disused machines, packaging and accessories.

Only for EU countries: Never dispose of power tools in your household waste! Used power tools must be collected separately and handed in for environmentally compatible recycling in accordance with European Directive 2002/96/EC on waste electrical and electronic equipment and its implementation in national legal systems. Special notes regarding cordless machines: Battery packs may not be disposed of with regular waste. Return faulty or used battery packs to your Metabo dealer! Do not allow battery packs to come into contact with water! Before disposal, discharge the battery pack in the power tool. Prevent the contacts from short-circuiting (e. g. by protecting them with adhesive tape).

Technical Specifications

Explanatory notes on the specifications on page 3. Changes due to technological progress reserved.

• P1 = Rated input
• P2 = Power output
• n0 = No-load speed
• n1 = On-load speed
• G = Drill spindle thread
• DR = maximum permitted agitator diameter
• D = Collar diameter
• m =weight with smallest battery pack/weight without cord
• Measured values determined in conformity with EN 60745.
• Machine in protection class II
• ~ AC Power
• Direct current

The technical specifications quoted are subject to tolerances (in compliance with the relevant valid standards).

Emission values
These values make it possible to assess the emissions from the power tool and to compare different power tools. The actual load may be higher or lower depending on the operating conditions, the condition of the power tool or the accessories. Please allow for breaks and periods when the load is lower for assessment purposes. Arrange protective measures for the user e.g. organizational measures based on the adjusted estimates.

Vibration total value (vector sum of three directions) determined in accordance with EN 60745:

• ah, D =Vibration emission value
• Kh,D =Uncertainty (vibration)
• Typical A-effective perceived sound levels:
• LpA = Sound-pressure level
• LWA =Acoustic power level
• KpA, KWA = Uncertainty
• Wear ear protectors!

Metabowerke GmbH
Metabo-Allee 1 72622 Nuertingen Germany.
www.metabo.com.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>