E-flite EFL71765 Turbo Timber SWS 2.0m BNF Basic and ARF Manual Addendum Instruction Manual
- June 16, 2024
- E-flite
Table of Contents
E-flite EFL71765 Turbo Timber SWS 2.0m BNF Basic and ARF Manual Addendum
Flap Setup
- The transmitter setup tables in the printed manual were incorrect.
- Use the following tables to correctly set the Aircraft Type and Flap System values.
- Follow the Flap Setup Procedure below to test the flap system function before attempting flight.
Flap Setup Procedure
- Before powering the model, disconnect the flap pushrod clevises from the flap control horns.
- With the flap switch in the up position (Pos 0: 0% travel), power the model and verify the servo arms are perpendicular to the wing surface.
- Adjust the clevises as needed to align each flap with the fixed inner portion of the wing trailing edge.
- Reconnect the clevises to the flap horns, and secure them with the tubing.
- Verify flap travel is 22mm (Pos 1), and 45mm (Pos 2). It may be necessary to make small adjustments to the Pos 1 and Pos 2 flap travel settings to achieve this.
DX Series Transmitter Setup
1. Power ON your transmitter, click on the scroll wheel, roll to System
Setup and click the scroll wheel. Choose yes.
2. Go to Model Select and choose < Add New Model> at the bottom of
the list. The system asks if you want to create a new model, select
Create
3. Set Model Type : Select Airplane Model Type by choosing the
aeroplane. The system asks you to confirm the model type, data will be reset.
Select YES
4. Set Model Name : Input a name for your model file
5. Scroll to Aircraft type, and click on the roller. Scroll to Wing:
click on the roller and scroll to select 1Ail 1Flap.
6. Select < Main Screen>, Click the scroll wheel to enter the Function
List
7. Set D/R (Dual Rate) and Expo ; Aileron
Set Switch : Switch F
Set High Rates: 100% , Expo 10% – Low Rates: 70% , Expo 5%
8. Set D/R (Dual Rate) and Expo ; Elevator
Set Switch : SWITCH C
Set High Rates : 100%, Expo 10% – Low Rates 70%, Expo 5%
9. Scroll to Throttle Cut ; Switch : Switch H,
Position: -100%
10. Scroll to Flap System
Set SWITCH D
Set POS 0: 0% FLAP 0% Elevator
Set POS 1: 38% FLAP 3% Elevator
Set POS 2: 68% FLAP 9% Elevator
Set SPEED 2.0s
Propeller
- The correct propeller size for this model is the included 15 x 8E (EFLP71764). Disregard any references to other sizes.
Motor/Thrust Reverse
- The included ESC requires an update to enable the thrust reversing feature. This can be accomplished with the use of a Spektrum Programming Box (SPMXCA200) and Windows PC.
- Alternatively, a programming card can be provided to you at no charge.
- If you prefer this option, send an email request to productsupport@horizonhobby.com.
- Include a photo of your purchase receipt and Turbo Timber SWS ESC Programmer in the subject line. Our Product Support team will send this as soon as possible.
NX Series Transmitter Setup
1. Power ON your transmitter, click on the scroll wheel, roll to System
Setup and click the scroll wheel. Choose yes.
2. Go to Model Select, click on the scroll wheel, and choose < Add New
Model> near the bottom of the list. Select Airplane Model Type by
choosing the aeroplane, select Create
3. Set Model Name : Input a name for your model file
4. Scroll to Aircraft type, and click on the roller. Scroll to Wing:
click on the roller and scroll to select 1Ail 1Flap.
5. Select < Main Screen>, Click the scroll wheel to enter the Function
List
6. Set Rates and Expo ; Aileron
Set Switch : Switch F
Set High Rates: 100% , Expo 10% – Low Rates: 70% , Expo 5%
7. Set Rates and Expo ; Elevator
Set Switch : SWITCH C
Set High Rates : 100%, Expo 10% – Low Rates 70%, Expo 5%
8. Scroll to Throttle Cut ; Switch : Switch H,
Position: -100%
9. Scroll to Flap System Set SWITCH D
Set POS 0: 0% FLAP 0% Elevator
Set POS 1: 38% FLAP 3% Elevator
Set POS 2: 68% FLAP 9% Elevator
Set SPEED 2.0s
iX Series Transmitter Setup
1. Power ON your transmitter and begin once the Spektrum Airware app is open.
Select the orange pen icon in the upper left corner of the screen, the system
asks for permission to Turn Off RF , select PROCEED
2. Select the three dots in the upper right corner of the screen, select
Add a New Model
3. Select Model Option, choose DEFAULT , and select Airplane. The
system asks if you want to create a new acro model, select Create
4. Select the last model on the list, named Acro. Tap on the word Acro
and rename the file to a name of your choice
5. Tap and hold the back arrow icon in the upper left corner of the screen to
return to the main screen
6. Go to the Model Setup menu. Select Aircraft Type The system asks
for permission to Turn Off RF , and select PROCEED. Touch the
screen to select the wing. Select 1 Ail 1 Flap.
7. Press and hold the back arrow icon in the upper left corner of the screen
to return to the main screen.
8. Go to the Model Adjust menu
9. Set Dual Rates and Expo ; Select Aileron
Set Switch : Switch F
Set High Rates: 100% , Expo 10% – Low Rates: 70% , Expo 5%
10. Set Dual Rates and Expo ; Select Elevator
Set Switch : SWITCH C
Set High Rates : 100%, Expo 10% – Low Rates 70%, Expo 5%
11. Select Flap System Set SWITCH D
Set POS 0: 0% FLAP 0% Elevator
Set POS 1: 38% FLAP 3% Elevator
Set POS 2: 68% FLAP 9% Elevator
Set SPEED 2.0s
12. Select Throttle Cut ; Switch : Switch H, Position: -100%
© 2024 Horizon Hobby, LLC. E-flite and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. Completed 1/24 EFL71765, EFL71750
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>