melchioni 118510026 INFINITY Iron With Continuous Charging User Manual

INFINITY

Iron with continuos charging

Cod. 118510026

User manual

1. INTRODUCTORY NOTE

Melchioni S.p.a., owner of the Melchioni Family brand, thanks you for purchasing this appliance. It is the result of a careful selection of features and the meticulous refinement of details, with the aim of offering a complete, versatile, reliable and highperformance solution for both the occasional and the most demanding users.

This manual contains important information both for the correct use of the appliance and for its safe operation. It is essential to read and understand its contents before performing any operations in order to obtain the best performance from the appliance. Keep this manual even after reading it, as you may need to refer to it in the future.

The Melchioni Family team is at your disposal for any advice, instructions or suggestions.

2. IMPORTANT INFORMATION FOR CORRECT, SAFE USE OF THE APPLIANCE

The following instructions must be read, understood and complied with before commissioning the appliance. They are especially useful for the protection of the safety, physical conditions and security of the operator and persons nearby, as well as for providing valuable information for preventing faults and malfunctions, for prolonging the service life, for reducing energy consumption and for environmental protection.

• The appliance is designed for household and non-intensive use. Any professional use compromises the safety requirement and is a condition for inapplicability of the warranty.
• The appliance is intended for indoor use and protected from inclement weather: use in an outdoor environment compromises the safety requirement and constitutes a potential hazard for the safety of the operator and persons nearby.
• The appliance must not be used if it shows deformations, bulges, cracks in the casing, missing parts or other structural anomalies. If these conditions occur, disconnect the power supply and contact qualified technical personnel.
• The appliance must not be used if it emits unusual noises, foul odours, smoke, vapours or any other type of exhalation not related to the cooking in progress. If these conditions occur, disconnect the power supply and contact qualified technical personnel.
• Slight smoke and a slight burning smell may occur when using the appliance for the first time: this situation is normal and does not constitute a fault or hazard unless it lasts beyond the first few minutes of use.
• The appliance must not be stored or used in excessively humid or dusty environments, in the presence of atmospheres saturated with gas, fumes, in excessive or low temperatures or under direct solar radiation.
• The appliance must not be used in explosive atmospheres, near explosive, combustible, detonating or flammable material (e.g. petrol pumps, gas cylinders, etc.). Such use constitutes a serious risk to the safety of the operator and persons nearby and may cause fires or deflagrations.
• Make sure that each part of the appliance, especially the cord, is placed at a safe distance from heat sources (e.g. electric or gas cookers), both during use and when not in use.
• During use, the appliance must be constantly supervised: do not use it in the absence of operators or persons who can constantly check its correct operation.
• During use, the appliance must be placed at a minimum distance of 20 cm from surrounding objects on each side: this precaution prevents parts from overheating and improves performance.
• Normal use of the appliance involves heating the soleplate to temperatures that can cause severe skin burns and lesions. Always exercise extreme caution to avoid contact with this surface during use.
• Beware of sudden bursts of hot steam from the soleplate during use: never press the steam release button except while ironing and with the soleplate resting on the fabrics.
• Use only the original accessories supplied. The use of non-original accessories could constitute a danger of damage to the appliance as well as a potential health hazard.
• Do not use empty; during use, regularly check the water level in the tank on the base.
• Ensure a standstill period of at least 30 minutes after 60 minutes of appliance use.
• Do not insert any objects apart from water into the tank on the base.
• Avoid touching any structural parts, even external ones, during operation, as some of them could reach high temperatures: the tank opening flap is subject to moderate heat and should be the only part to be touched.
• Do not cover the appliance with any heat reflective material (e.g. aluminium). Doing so will lead to the appliance overheating, with the possibility of breakdowns and danger to the operator or people nearby.
• Make sure that every part of the appliance has cooled down adequately before storing it.
• Do not use the appliance if one or more of the parts listed in the following chapter are missing or damaged: contact your dealer for repair.
• Periodically check the conditions of the parts making up the appliance, in particular the power cord: if any anomalies are found, refrain from using the appliance and contact qualified technical personnel.
• Periodically check the cleanliness of the soleplate: refer to the following chapter on cleaning if limescale or dirt build-ups are found.
• Do not use abrasive sponges or aggressive detergents for cleaning operations: refer to the following chapter for complete requirements.
• Cleaning operations must be carried out taking care to disconnect the appliance from the power supply: refer to the following chapter for the relevant requirements.
• The appliance must be connected to a compliant electrical system. The electrical system must have a power rating equal to or greater than that of the appliance and must be earthed.
• Before connecting the plug of the power cord to the socket, make sure that the voltage of your household installation corresponds to the voltage indicated on the appliance.
• Do not connect the appliance to extension cords, power strips, multi-socket strips, timers, controlled sockets or other devices that can start it up independently.
• If the appliance is not to be used for a prolonged period of time, it is advisable to unplug the power cord from the socket: this will extend the life of the appliance and help reduce energy consumption.
• Do not disconnect the power supply by pulling on the cord: grasp the plug firmly with one hand, place the other hand on the frame of the electrical outlet and disconnect with a quick, sharp movement.
• Before disconnecting the appliance, make sure that it is switched off, unless you need to disconnect it in an emergency situation due to abnormal behaviour as described in this chapter.
• The appliance must be kept out of the reach of children under 8 years of age; in any case make sure that it is not used for play.
• If the appliance is used by children, even if they are over 8 years old, or by persons with reduced cognitive, sensory or motor skills, they must be instructed about the dangers of incorrect use of the appliance and it must be guaranteed that the information has been correctly and fully understood. Adequate supervision must however be ensured.
• Do not use the appliance in the vicinity of liquid accumulations or sources, such as tanks, tubs, showers, sinks, other sanitary fixtures, faucets, pipes, sprinklers, bottles, storage vessels, expansion vessels, watercourses, flowerpots and similar. Do not place containers holding liquids on top of the appliance; make sure that the power cord or electrical plug is never submerged.
• There is no reason to disassemble the appliance, not even after it has been decommissioned. It is composed of parts that could be swallowed by children or persons with reduced cognitive ability.
• Do not carry out any repairs yourself; in the event of a fault, have the appliance inspected by a qualified technician.
• None of the parts of the appliance must be modified under any circumstances: doing so normally constitutes a serious impairment of the safety requirement, a condition for immediate forfeiture of the warranty and does not lead to any increase in performance.
• Do not subject the power cord to excessive bending or kinking: any internal damage to the cable which cannot be detected constitute a serious safety hazard.
• Place the appliance at an adequate distance from moving parts such as curtains, door and window sashes, hatches or similar in order to avoid accidental contact.
• Place the appliance on a flat, stable surface and ensure that the appliance cannot move independently due to gravity or external forces.
• Keep this manual for future reference.

3. IDENTIFICATION OF PARTS

A: Tank
B: Iron
C: Connecting tube outlet
D: Steam trigger
E: Keypad
E1: Power button
E2: Automatic cleaning button
E3: Steam level button
F: Lighted display panel
G: Iron locking lever
H: Iron release buttons
I: Tank filling spout
J: Temperature regulation knob

4. COMMISSIONING AND FIRST START-UP

Some preliminary operations are necessary before first use. Proceed as follows:

• Unpack the appliance and check the conditions and completeness of the equipment, as indicated in the previous chapter.
• Keep the packaging for 15 days in case it needs to be returned to the retailer; after this period, dispose of it in accordance with the instructions on the separation of materials indicated on it.
• Read this manual in its entirety, paying particular attention to the instructions for safe use.
• Carefully remove all possible fastening materials from parts, including internal parts.
• Fully remove any stickers from the surface of the appliance.
• Place the appliance on a flat, stable surface, taking care to reserve 10 cm of space on all sides, at the rear and above the appliance for the necessary air circulation.
• Refer to chapter 2 for further details and instructions on appliance positioning and installation.
• Fully unwind the power cord.
• Using the supplied cup, carefully fill the tank through the front closable spout, without ever exceeding the MAX notch.
• Turn the temperature selector to [ ]
• Connect the electrical plug to a wall socket with a regular upstream earth leakage circuit breaker.
• Ensure that the cord does not come into contact with hot parts and that it is not subjected to excessive bending or kinking.
• Press the button [ ] to start up the appliance.
• Press the [ ] button repeatedly until the icon (maximum steam level) lights up.
• Wait for the [ ] icon to switch from red to green (approx. 1 min.)
• Release the iron from the base by pressing both front PUSH buttons simultaneously.
• Hold the iron in a horizontal position over a surface suitable for collecting any water (e.g. a bucket or the drainer of a sink).
• Press and hold the steam trigger for about 30 seconds. The pump should start immediately, making a low buzzing sound from the base. Then, after 15 minutes, the soleplate should start producing a light cloud of steam.
• Check that production increases, swinging the iron and holding the soleplate parallel to the horizontal surface.
• Check the parts of the appliance and proceed with its normal use, if necessary.

5. USING THE APPLIANCE

Filling the tank
The tank must be filled with the appliance switched off and the power cord disconnected. If necessary, hold the [ ] key pressed until all the icons have switched off except for [ ], which will light up in red. Pull the plug out from the socket, gently open the front spout (I) and use its slope to facilitate pouring the water into the tank.
During this operation, remember that:

• Using the supplied cup with a spout is preferred and will facilitate this operation.
• Never fill the water past the MAX notch. Overfilling may result in overflowing and spills, causing an inconvenience to the user and a potential hazard.
• The appliance is fitted with a filter that demineralises the water by means of a chemical/physical reaction, thus allowing the use of normal tap water. The use of distilled water and similarly scented substances or flow aids can modify the material properties of the filter, making it ineffective. All types of water additives available on the market should thus be strictly avoided.

After filling, close the tank by gently pressing on the spout.

Selecting the temperature and releasing the iron
Once the tank is filled, insert the plug in the mains socket again, then press the [ ] button. The soleplate will slowly start to heat up. Use this period of time to select the desired ironing temperature with the knob (J), as per the following table:

| Synthetic, nylon, acrylic, polyester, rayon
---|---
| Wool, silk
| Cotton, linen

The ideal ironing temperature for each garment can easily be found on the clothing label itself, showing the same symbols as the table. If the symbol is shown, this means the garment is made of a fabric that is not intended for ironing. The additional MIN and MAX markings indicate an extremely low or extremely high temperature, normally used on fabrics with special characteristics or for non-ironing operations (e.g. label transfer, edging, etc.).

The appliance is ready for ironing when the icon turns green. Release the iron from the base by simultaneously pressing both PUSH buttons on the sides of the base, then gently lift the iron and proceed to iron.

Selecting and delivering steam
During normal ironing operations, steam is delivered by pressing the trigger (D) located under the iron handle. Steam is only delivered when the trigger is pressed and stops when it is released. Depending on the type of fabric used, the volume of delivered steam can be adjusted by pressing the relative button (E3), according to the following table:

| Synthetic fibres (polyester, nylon, etc…)
---|---
| Wool, silk
| Cotton, linen

Each time the button (E3) is pressed again, the selected steam level icon lights up in green, cyclically. Remember that:

• The steam produced is effectively increased or decreased a few seconds after the selection. This is because each time a change is made, the water circuit must reach the new set value.
• A higher pressure value entails proportionately higher water consumption. If the maximum pressure is used, frequently check the tank level.

Steam burst
In some cases, for example when removing particularly stubborn creases, it is possible to deliver very intense steam in a very short time. This is called a “steam burst” and is useful in the case of very thick fabrics such as denim. To deliver a steam burst, hold the iron over the crease, then quickly press the delivery trigger (D) twice. The iron will release an exceptionally high volume of steam for about six seconds. For very delicate fabrics, it may be necessary to lift the iron a few centimetres off the ironing surface. Consider that the steam burst causes the soleplate to noticeably cool. Therefore, the soleplate should be allowed to heat up again after a steam burst, waiting preferably 15­20 seconds between consecutive bursts.

Automatic standby
To reduce energy consumption, the appliance suspends soleplate heating if the iron is not used for more than eight minutes. The icon flashes and soleplate heating is suspended until the next time any of the iron buttons are pressed. It is highly likely that the soleplate, having cooled down in the meantime, will need to be compensated by an additional period of heating, indicated by the icon in red. Therefore, wait for the icon to turn green before starting to iron again, which should take between 15 and 30 seconds.

At the end of ironing
After use, turn off the appliance by pressing the [ ] button for three seconds. The steam level icon turns off and the icon turns red. Disconnect the power cord from the socket and wait for the soleplate to completely cool. Then empty the receptacle, pouring the residual water from the front spout into a household drain. Place the iron on the base, pointing it backwards and lowering the front part into the seat, then lock it by flicking up the locking lever (G) until a click is heard. Check that the iron is properly locked by lifting the entire appliance with the iron handle. Do not stow the appliance until having satisfied the above as the high temperature or presence of water may cause a hazardous situation. If necessary, dry any wet parts with a dry cloth.

6. CLEANING AND MAINTENANCE

Automatic cleaning
At regular intervals, approximately every 50­100 hours of ironing, the soleplate must be automatically cleaned. This operation involves removing any limescale and other Salts that could be obstructing steam delivery. To perform this operation, proceed as follows:

1. Fill the tank as previously described.
2. Connect the appliance to the mains without taking the iron off the base.
3. Turn on the appliance by pressing the [ ] button and wait for the soleplate to reach temperature ( icon turns green)
4. Press the button (E2) for three seconds. The relative icon turns red.
5. Wait for the icon to turn off (approximately 2 minutes). During this stage, the appliance starts producing large volumes of steam and liquid water, which builds up on the resting surface, where it can be removed using a dry cloth.
6. When the icon turns off, wait for the soleplate to heat up until the icon turns green
7. If appropriate, proceed with normal ironing.

Additional cleaning and maintenance instructions
Clean the surfaces of the appliance strictly with a damp cloth, making sure to disconnect the power plug from the socket. In any case, avoid aggressive detergents, abrasive sponges, steel wool or other chemical cleaners. Never clean the solepate except in the event of blatant contaminations in the event of improper use. See the specific products or contact a technical support service. Before reconnecting the appliance after cleaning, check that all parts are perfectly dry.

7. TROUBLESHOOTING

Problem

| Possible cause| Probable solution
---|---|---
The display won’t turn on and/or the soleplate does not heat up| The power cord is disconnected|

Connect the power cord

The electrical outlet is not powered

| Check the switches on the electrical panel
The appliance is overheating| The appliance has been used for too long|

Turn off the appliance and wait for it to cool before using it again

The appliance produces smoke and odours

| The soleplate is dirty| Check the soleplate for any contaminations and then clean only with the specific products or contact a specialised technician
Steam production has significantly decreased| The soleplate nozzles are clogged  |

Perform automatic cleaning as outlined in Chap. 6

The iron does not lock into the base

| The mechanism is blocked or out of position|

Check the correct positioning of the iron on the tank: the lock bar must be inserted between the soleplate and the iron

Should any malfunctions other than those listed above occur, a self-sufficient solution is not feasible and the product must be inspected by a qualified technician.

8. TECHNICAL DATA

Power supply voltage                     : 220 ­- 240 V AC 50 Hz
Maximum power                            : 2000 W
Tank capacity                                 : 1.5L
Steam production                           : 28g/min
External dimensions (L x H x D)   : 17.9X24.1X34.6cm
Weight                                            : 2.49Kg

9. PRODUCT COMPLIANCE

The producer Melchioni Spa declares that the product Iron with continuos charging Mod. INFINITY (cod. 118510026) is in compliance with Directive 2014/30/EU of the European Parliament and of the Council, of 26 february 2014, on the harmonisation of the laws of the Member States relating to electromagnetic compatibility.

The producer Melchioni Spa declares that the product Iron with continuos charging Mod. INFINITY (cod. 118510026) is in compliance with Directive 2014/35/EU of the European Parliament and of the Council, of 26 february 2014, on the harmonisation of the laws of the Member States relating to the making available on the market of electrical equipment designed for use within certain voltage limits.

The producer Melchioni Spa declares that the product Iron with continuos charging Mod. INFINITY (cod. 118510026) is in compliance with Directive 2009/125/EC of the European Parliament and of the Council, of 21 october 2009, establishing a framework for the setting of ecodesign requirements for energy- related products.

The producer Melchioni Spa declares that the product Iron with continuos charging Mod. INFINITY (cod. 118510026) is in compliance with Directive 2011/65/EU of the European Parliament and of the Council, of 8 june 2011 and subsequent Commission Delegated Directive 2015/863, on the restriction of the use of certain hazardous substances in electrical and electronic equipment.

According to Directive 2012/19/EU of the European Parliament and of the Council, of 4 july 2012, on waste electrical and electronic equipment (WEEE), the presence of the crossed-out bin symbol indicates that this appliance is not to be considered as urban waste: its disposal must therefore be carried out by separate collection. Disposal in a non-separate manner may constitute a potential harm to the environment and health. This product can be returned to the distributor when purchasing a new device. Improper disposal of the appliance constitutes misconduct and is subject to sanctions by the Public Security Authority. For further information, contact the local administration responsible for environmental matters.

10. PRODUCT WARRANTY

Melchioni Spa, based in Milan (Italy), via Colletta 37, recognizes a conventional guarantee on the product for a period of two years from the date of the first purchase by the consumer. This guarantee does not affect the validity of the legislation in force concerning consumer goods (Legislative Decree 6 September 2005 n. 206 art. 128 and following), of which the consumer remains the owner. This guarantee applies to the entire territory of the European Union.

The components or parts that are found to be defective for ascertained manufacturing causes will be repaired or replaced free of charge through the dealer, during the above warranty period. Melchioni Spa reserves the right to make a complete replacement of the device, if repairability is impossible or excessively expensive, with another device of similar characteristics (Legislative Decree 6 September 2005 no. 206 art. 130) during the warranty period. In this case, the validity of the warranty remains that of the original purchase: the service provided under warranty does not extend the warranty period.

In any case, this appliance will not be considered defective in terms of materials or manufacture should it be adapted, changed or adjusted, in order to comply with national or local safety and / or technical standards, in force in a country other than that for which it is was originally designed and manufactured. This appliance has been designed and built for domestic use only: any other use will invalidate the benefits of the guarantee.

The warranty does not cover:

• parts subject to wear or tear, nor those parts that require periodic replacement and / or maintenance
• professional use of the product
• malfunctions or any defects due to incorrect installation, configuration, software / BIOS / firmware update not performed by authorized Melchioni Spa
• repairs or interventions carried out by persons not authorized by Melchioni Spa
• manipulation of assembly components or, where applicable, of the software
• defects caused by fall or transport, lightning, voltage fluctuations, liquid infiltration, opening of the appliance, bad weather, fire, public disturbances, inadequate ventilation or incorrect power supply
• any accessories, for example: boxes, bags, batteries, etc. used with this product
• home interventions for convenience checks or presumed defects

The recognition of the guarantee by Melchioni Spa is subject to the presentation of a tax document that proves the actual date of purchase. The same must not show any tampering or deletions, in the presence of which Melchioni Spa reserves the right to refuse the provision of treatment under warranty.
The warranty will not be recognized if the serial number or model of the appliance is non-existent, abraded or modified.
This warranty does not include any right to compensation for direct or indirect damage, of any nature, to people or things, caused by any inefficiency of the appliance. Any extensions, promises or services in this regard, insured by the retailer, will be borne by the latter.

Melchioni Spa
Via P. Colletta 37, 20135 Milano | Tel: 02/49486000 | www.melchioni- ready.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>