real flame 5092 Electric Heater Slim Vivid Flame Electric Firebox User Manual

real flame 5092 Electric Heater Slim Vivid Flame Electric Firebox

Product Information

Specifications

• Model : 5092
• Product Code : 04182024-5
• Power Requirements : 15 amp, 120 volt circuit
• Glass Type : Tempered glass

Product Usage Instructions

Important Safety Instructions
Always follow these safety precautions when using the firebox:

1. Read the user manual before use.
2. Avoid direct contact with the hot surfaces.
3. Do not operate with broken or chipped glass.
4. Use qualified service personnel for glass replacement.

Operation and Features
The firebox comes with the following features:

• Power: Use the remote control to turn the unit ON/OFF.
• Adjust Brightness: Control flame brightness levels.
• Adjust Flame: Change flame color.
• Timed Shut-Off: Set automatic shut-off time.
• Dynamic Embers: Creates realistic fire effect by adjusting ember glow.

Site Selection and Preparation
Choose a suitable location for the firebox:

1. Ensure proper ventilation around the unit.
2. Avoid placing near flammable materials.
3. Keep away from water sources.

Care and Maintenance
Maintain your firebox for optimal performance:

1. Clean the glass with non-abrasive cleaners.
2. Regularly check for any signs of damage.
3. Keep the area around the firebox clear of debris.

Installation
For proper installation of the firebox:

1. Ensure a dedicated circuit is available.
2. If circuit breaker trips frequently, use a dedicated circuit.
3. Follow manufacturer’s instructions for installation steps.

IMPORTANT SAFETY INFORMATION

IMPORTANT NOTICE

Please keep this user’s guide for future reference. When using electric appliances, basic precautions should always be followed to reduce the risk of fire, electric shoc and injury to persons, including the following:

1. Read all instructions before using this appliance.
2. The heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. The trim around the heater outlet becomes how during heater operation. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front, sides and rear of the unit.
3. Extreme caution is necessary when any heater is used by or near children or persons with disabilities and whenever the unit is left operating and unattended.
4. Always unplug the electric heater when not in use.
5. Do not operate any unit with a damaged cord or plug, or if the heater has malfunctioned, or if the electric heater has been dropped or damaged in any manner. Return heater to authorized service facility for examination, electrical or mechanical adjustment, or repair.
6. Do not use outdoors.
7. The electric heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate heater where it may fall into a bathtub or other water container.
8. Do not run the cord under carpeting, furniture, or appliances. Do not cover cord with throw rugs, runners, or the like. Arrange cord away from high traffic areas, where it will not be tripped over.
9. To disconnect the unit, turn the firebox off and then remove the plug from the outlet.
10. Connect to properly grounded outlets only.
11. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock, fire, or damage to the heater.
12. To prevent a possible fire, do not block air intake or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
13. All electrical heaters have hot, arcing or sparking parts inside. Do not use in areas where gasoline, paint, or flammable liquids are used or stored or where the unit will be exposed to flammable vapors.
14. Do not modify the electric heater. Use it only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, injury or death.
15. Do not burn wood or other materials in the electric heater.
16. Do not strike the glass panel.
17. Always use a certified electrician if new circuits or outlets will be required.
18. Always use properly grounded, fused and polarized outlets.

Glass Information

1. Under no circumstances should this product be operated with a broken or chipped glass panel.
2. Do not strike or slam the glass.
3. Do not use abrasive cleaners to clean the glass.
4. This product uses tempered glass. Replacement of the glass supplied by the manufacturer should be done by qualified / authorized service personnel only.

SAVE THESE INSTRUCTIONS

WARNING

• Risk of electric shock.
• Do not open.
• Non-user serviceable parts inside.

DESCRIPTIONS OF WARNINGS

• NOTE: Procedures and techniques that are considered important enough to emphasize.
• CAUTION: Procedures and techniques which, if not carefully followed, will result in damage to the equipment.
• WARNING: Procedures and techniques which, if not carefully followed, will expose the user to the risk of fire, serious injury, illness or death.

NOTE This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on.

The user is encouraged to try to correct the interference by on or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.

Operation is subject to the following two conditions:

1. This device may not cause interference and;
2. This device must accept any interference, including interference that may cause undesired operation of the device.

NOTE A 15 amp, 120 volt circuit is required. A dedicated circuit is preferred but not essential in all cases. A dedicated circuit will be required if, after installation, the circuit breaker trips or fuse blows on a regular basis when the heater is operating. Additional appliances on the same circuit may exceed the current rating of the circuit breaker.

If you have any questions about our products please contact Real Flame® customer service at 1-800-654-1704

• Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate.
• Even used batteries may cause severe injury or death.
• Call a local poison control center for treatment information.
• Battery type: CR2025
• Battery voltage: 3V
• Non-rechargeable batteries are not to be recharged.
• Do not force discharge, recharge, disassemble, heat above 140°F (60°C) or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns.
• Ensure the batteries are installed correctly according to the polarity (+ and -).
• Do not mix old and new batteries, different brands or types of batteries such as alkaline, carbon-zinc, or rechargeable batteries.
• Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations.
• Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.

WARNING

• INGESTION HAZARD: This product contains a button cell or coin battery.
• DEATH or serious injury can occur if ingested.
• A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours.
• KEEP new and used batteries OUT OF REACH of CHILDREN. Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body.
• Battery Type/Voltage: CR2025/3V
• INGESTION HAZARD: This product contains a button cell or coin battery.

OPERATION AND FEATURES

Using the Remote Control

Using the Control Panel

NOTE

• When turned OFF the embers of the log set will not immediately go out. This is a designed feature to represent the embers of the fire slowly fading out.
• Although the heater has been turned off, the fan may still run to prevent over heating.
• If the display screen ready 88 or EE verify that all vents on the firebox are clear of any obstructions then unplug the firebox and plug it back in to reset the firebox. If the problem persists please contact Real Flame at 1-800-654-1704.

SITE SELECTION AND PREPARATION

WARNING

• Ensure the power cord is not installed so that it is pinched or against a sharp edge and ensure that the power cord is stored or secured to avoid tripping or snagging to reduce the risk of fire, electric shock or injury to persons.
• Construction and electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire, electric shock and injury to persons.
• Do not attempt to wire your own new outlets or circuits. To reduce the risk of fire, electric shock or injury to persons, always use a licensed electrician.

See figure 1 for grounding instructions. This heater is for use on 120 volts. The cord has a plug as shown at A in Figure 1. An adapter as shown at C is available for connecting three-blade grounding-type plugs to two-slot receptacles. The green grounding lug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available.

This section provides easy step-by-step instructions for selecting a location and preparing the site to install the fireplace into any Real Flame® fireplace mantel.

NOTE

• The fireplace insert comes completely assembled and wired. Some tools may be required to prepare the site and install the trim.
• The dimensions of the fireplace insert are 27.48” wide x 18.31” high x 5.39” deep.
• You should allow 1/4” around the fireplace insert for ease of installation.
• This fireplace does not require any venting.

Select a suitable location that is not susceptible to moisture and is away from drapes, furniture and high traffic. For ease of electrical hook up you may wish to position the fireplace near an existing outlet.

CARE AND MAINTENANCE

Battey Replacement

• Slide the battery cover open by squeezing the release lever while pulling the battery out. Please see the underside of remote for instructions.
• Replace the dead battery with one CR2025 battery. Replacement batteries are not included with the firebox.
• Do not dispose of the dead battery in the municipal trash. Batteries should be disposed of at a local collection point for recycling batteries.
• Close the batter cover.

Light Emitting Diode
This firebox is fitted with LED (Light Emitting Diode) bulbs in place of conventional bulbs. These generate the same light levels as conventional bulbs, but use a fraction of the energy. These LED bulbs are maintenance free and should not require replacing during the life of the product.

Cleaning

WARNING
Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire, electric shock, injury or death.

CAUTION
When transporting or storing the unit and cord, keep in a dry place, free from excessive vibration and store so as to avoid damage.

• Dust the unit using a clean dry cloth.
• Use warm water and a clean cloth to wipe off all painted surfaces. Do not use abrasive cleaners.
• Use a standard glass cleaner for the glass panel of the unit.

Installing the 5092 Electric Firebox

WARNING Read and understand all instructions included with your firebox before installing this unit.
Follow the steps below to install the electric firebox into your Real Flame® fireplace mantel

1. Step One: Figure 1
   From the rear of the mantel, insert the firebox into the opening.
   NOTE : Your mantel may vary slightly from the one depicted in this illustration.

2. Step Two: Figure 2
   Attach the firebox to the back of the mantel with the 4 supplied screws.

WARRANTY

Limited Warranty
Real Flame® warrants that the following components of this Real Flame® fireplace (“the Product”) will be free from manufacturing defects in material and workmanship after correct assembly and under normal use and proper maintenance for the periods indicated below, commencing with the date of purchase of the Product:

• The body – 1 year limited warranty.
• The internal components – 1 year limited warranty.

This non-transferable warranty extends to the original purchaser only, provided that the purchase was made through an authorized Real Flame dealer. The warranty is also subject to the following conditions and limitations:
This warranty does not extend to damages caused by shipping, improper assembly, installation or storage, installation that does not comply with building codes and ordinances, installation or operation not in accordance with the included manual, abuse, lack of maintenance, hostile environments, accident, natural weather, or unworkmanlike repairs. Modification of the Product, use of fuels other than what is approved by Real Flame, or use of parts installed from other manufactures will nullify this warranty.

This warranty applies to the functionality of the Product only and does not cover cosmetic issues such as scratches, dents, rust, oxidation, corrosion, areas discolored or cracked due to prolonged exposure to extreme heat, or damage caused by abrasive or chemical cleaners. However, should deterioration of parts occur to the degree of non-performance within the duration of the warranty period, Real Flame will provide a replacement part.
Real Flame requires reasonable proof of your date of purchase. Therefore, you should retain your sales receipt and/or invoice. Defective parts subject to this warranty will not be replaced without proof of purchase.
Real Flame must have the opportunity to verify the alleged defect. In order for any internal components to be covered under warranty, Real Flame requires the user to troubleshoot with a Real Flame Customer Service member to ensure proper operation and diagnosis of issue.

In the event of covered defects in warrantied items, Real Flame will, at its sole option and discretion, replace the defective component, replace the Product or refund the purchase price. Real Flame is not responsible for the installation, labor or any other costs associated with the reinstallation. The foregoing is the exclusive remedy under the terms of this limited warranty. Real Flame will not be responsible for any incidental or consequential damages caused by defects in the Product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This limited warranty is the sole express warranty given by Real Flame. The duration of any implied warranty arising under the laws of any state, including implied warranty of merchantability or fitness for a particular purpose or use, is limited to the duration of the warranty specified above. Some states do not allow limitations on how long an implied warranty lasts, so this limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from State to State.

For warranty service:

1. Call Real Flame Customer Service at 1-800-654-1704 for technical support and troubleshooting.
2. If experiencing issues with finish, please fill out the ‘Outdoor Warranty Claim’ form at

www.realflame.com.

RETURN POLICY

• Return Policy
  You may return your purchase within 90 days of receipt. No refunds will be issued for incomplete or unauthorized returns. All returned products must be 100% complete, adequately packaged in original packaging and in resalable condition. Products that have been assembled or modified will not be eligible for return. All items must be returned in their entirety, meaning all items included must be returned together. No returns or exchanges on discontinued items. Please begin the return process by contacting the store or company where you bought your Real Flame® item.

• Replacement Parts
  In the event that an item has been lost or damaged, either by the manufacturer or in shipping, you may request a replacement. Replacement parts are not available for all units and only given at Real Flame’s discretion. We will assess any damage and find a solution, which could include shipping you a replacement. No replacements are available for discontinued items or repackaged (open box) products. Please call Real Flame Customer Service at 1-800-654-1704 for replacement parts before returning the damaged item. Please have the following information (which can be found in your instruction manual) ready before you call Customer Service:

  • Model number of item
  • 4-8 digit part number
  • Shipping address
  • A picture of the damaged item may be requested. Pictures should be sent to csrep@realflame.com

Incorrect Order Received

• If you received something other than what you ordered, please contact Real Flame Customer Service at 1-800-654-1704 within 48 hours of receiving the item.
• Refer to www.realflame.com for our complete return guidelines and policies.
• Please register your fireplace for recall notifications, proof of ownership and quality assurance at https://www.realflame.com/registration.

Real Flame®

• 7800 Northwestern Ave.
• Racine, WI 53406

USA

• Customer Service: 1-800-654-1704 in USA
• Service à la clientèle: 1-800-363-6443 in Canada

csrep@realflame.com

FAQ

Q: What should I do if the glass panel is broken?
A: Do not operate the firebox and contact qualified service personnel for glass replacement.

Q: Can I use abrasive cleaners on the glass?
A: No, only use non-abrasive cleaners to clean the glass panel.

Q: How do I adjust the flame color?
A: Use the remote control to change the flame color settings on the firebox.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>