Lights F6 Mood Lamp With Arduino User Manual
- June 3, 2024
- Lights
Table of Contents
F6 Mood Lamp With Arduino
**User Manual
LED Mood Lamp**
F6 Mood Lamp With Arduino
Dear customer
Thank you for choosing Mood Lamp. This introdyction will help you to properly
install and use your new lamp.Please read these carefully before using and
keep them for future reference.
PACKAGE CONTENTS
1x Mood lamd
1x AdaDter
1x Remote Control
1x User Manual
SAFETY INSTRUCTIONS
- Please read the instruction manual before using the lamp
- To ensure the longer life, please do not install near heat. corrosive or damp place.
- instaliation at the point that no shock. momentum and fire. Do not lef it fall from high place and avoid a crash.
- Berore cieaning.make sure that the lamp is disconnected from the power supply.
- Before using the lamp, please check if the lamp is damaged during transport. if the lamp has shown any damage, do not use or install the lamp. 6.Please do not dlisassemble or repair the lamp yourself.
INSTALLATION
To ensure the normal work of the lamp. please use the appropriate voltage. Press the power bufton on the remote control to furn on/off. For convenience.the lamp automatically switches on when initially connected to power.
USAGE
Size
SPECIFICATION
| Product name | LED Mood Lamp |
|---|---|
| Model | ZHT-F6 |
| Materia | ABS+Aluminium+PC |
| Voltage | AC100-240V 50/60Hz |
| LED SOURCE | RGBW(Colorful Chase) |
| Wattage | 17W(max)/ LED:9W/Charge:8W |
| Brightness | 1000LM |
| Angle | 360° |
| USB Port | Yes. Output: 5V 2A |
| Größe | Ф101xH36.9mm |
| Protection Grade | IP20 |
Changing Lighting Elfect Modes, Speeds, and Colors
Switch between the 6 lighting effect modes by pressing the mode button.
Switch between the 4 lighting effect speeds by pressing the left s button to
decrease speed or right
S putton to increase speed (all modes except static mode). Switch colors
within modes by pressing the top C button to go forward througn the colors or
bottom C button to go backward through the colors.
| Mode | Effect | Color Change Sequence |
|---|---|---|
| 1 | Static | Red-Green-Blue- Yellow- Aqua Marine – Purple -Warm White |
| 2 | Stack | Red-Green-Blue- Yellow- Aqua Marine-Purple-White |
| 3 | Pulse | Red-Green-Blue- Yellow- Aqua Marine- Purple- Warm White |
| 4 | Three- | |
| Color Chase | Red,Blue,Green-Green,Yellow,Blue- Blue,Aqua Marine,Yellow |
-Yellow.Purple.Aqua Marine – Aqua Marine,White.Purple – Purple. Red.White-
White.Green,Red
5| Three-
Color Rotate| Red,Blue,Green-Green,Yellow,Blue- Blue,Aqua Marine,Yellow
-Yellow.Purple.Aqua Marine – Aqua Marine,White.Purple – Purple. Red.White-
White.Green,Red
6| Attracting
(Automatic)| Red,White-Green,Red-Blue.Green- Yellow,Blue- Aqua Marine,
Yellow- Purple.Aqua Marine -White,Purple
Using Auto Mode
Press the guto bulton once for rainbow swvirl and a second time for pulse
color cycing. the third time for jump color cycling.
Adjusting Light Brightness
Switch down through the 4 brightness leveis by pressing the bnghtness
adjustment button (static mode only).
Lighting Memory Function
The lamp automatically switches on with.the last-used lighting setup so you
don’t need to set it again.
If power is disconnected, the lamp will switch on in the default warm white
light setting next time.
Managing & Using Presets
- Press the sef button to save your current custornized lighting setup as a preset for quick access any time. Lamp will flash once to indicate a preset is saved.
- Press the memory button to toggle between your saved presets.
- A fotal ot up to 7 custom presets can be stored. and old presets will be replaced when the preset memory is full.
- Select a preset you’ve saved and press the delete butfon fo delete it. The lamp will then switch to your next preset.
- If power is disconnected. presets will still be retained except for preset speed settings.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
RF Exposure Statement The distance between user and products should be no less
than 20cm.
http://www.touchstone-china.com/qrcode/qrcodeble.html
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>