AIGOSTAR 100801TYR Dimmable Outdoor LED Strip Instruction Manual

100801TYR Dimmable Outdoor LED Strip
Instruction Manual

Please read this manual carefully before operating your product. Even if you pass your product to others, please also follow the below instructions and operator safety. We do not take responsibility for improper use or not following this operation manual and safety advice that lead to damage to property or even injury to persons. Any warranty daim is also deemed void.
Please check whether the product is complete. If you find any defects, please contact the salesman immediately and make sure the package is ok.

PARTS

• Led strip 5M |
• 2 screws and 1 pc adhesive tape
• Controller
• Remote control (CR2025, 3V button battery included)
• Adapter
  

Note

1. The way to test the photoelectricity parameter value of the product: Take a 0.5m strip light and test it with a DC power supply, and read the bare light source data.
2. Test conclusion:
   Goods Code| DC Voltage| Power| CCT| Luminous flux| Energy efficiency grade
   ---|---|---|---|---|---
   100801TYR| 12V| 1.8W| 3000K| 185Im| F

3. Class ΙΙ

WARNING:

1. THE PRODUCT IS NOT A TOY, PLEASE TAKE THE PRODUCT AND PACKAGE FAR AWAY FROM ADULTS OR CHILDREN WHO CAN NO EVALUATE THE RISK.
2. THE PRODUCT NEEDS TO INSTALL BY A QUALIFIED ELECTRICIAN AND INSTALLED IN ACCORDANCE WITH LOCAL REQUIREMENTS.
3. PLEASE TURN OFF THE POWER SUPPLY BEFORE ANY OPERATIONS.
4. THE PRODUCT NEEDS TO BE CLEANED PRODUCT WITH SHARP OR ABRASIVE DETERGENT.
5. ELECTRONIC WASTE AND ELECTRONIC DEVICES CAN NOT DISPOSE OF WITH ORDINARY HOUSEHOLD WASTE.
6. MAKE SURE TO KEEP AND DISPOSE OF IT CAREFULLY. DO NOT THROW THE BATTERY INTO THE FIRE OR IMMERSE IT IN WATER.
7. DO NOT LOOK DIRECTLY INTO THE LIGHT.
8. PLEASE PUT THE PRODUCT ON A DRY SURFACE, AND KEEP A SAFETY DISTANCE AWAY FROM THE OVEN AND HEATER TO AVOID EXTREME TEMPERATURE, ELECTROSTATIC INTERFERENCE, STRONG IMPACT, AND HIGH VOLTAGE.
9. ONCE THE PRODUCT BREAKS OR MALFUNCTIONS, PLEASE TURN IT OFF_ IMMEDIATELY AND CONTACT_QUALIFIED ELECTRICIAN OR SERVICE PROVIDER TO DEAL WITH IT.
10. I FIND A LEAKING BATTERY, PLEASE MAKE SURE TO AVOID OUR SKIN, EYES, AND MUCOSA TO TOUCH THE BATTERY SACID. IN CASE OF CONTACT WITH SKIN WASH IMMEDIATELY WITH PLENTY OF WATER.

Parameter

• Battery type: CR2025 3V Button battery
• Remote control range: About 5m
• LED stripIP65
• Adapter & Wire: P20
• Dispose of in a controlled manner for recycling Replace the battery of the remote control
  

We suggest replacing the battery when the remote control performance reduction. Before inserting the battery, please make sure the touch point between the remote control and the battery is clean. And dean them if necessary.

1. Slide the battery cover in the arrow direction indicated and disassemble.
2. Take down the exhausted battery and install a new battery (CR 2025) if necessary. Please pay attention to polarity(+/-) when replacing batteries.
3. Install the battery into the remote control

Installation

1. Clean the surface.
2. Measure the desired length.
3. Cut to size(it should be operated in the place where marked scissors and the interval of KC/can be cut).
4. Peel off the protective foil.
5. Stick the strip in place.
6. Conned strip to the controller.
7. Use screws a tape to mount the controller to any surface.
8. Connect the controller to the DC adapter.
   

Remote control instructions

The remote control uses a CR2025 3V button battery. The remote control is on automatic standby mode when not in use. Normally the battery can be used for more than six months. The battery can be replaced by the same type.
2-year quality guarantee under the cared operations.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>