milleteknik 350-164 Voltage Converter 24V-12V 6A Instruction Manual
- June 11, 2024
- Milleteknik
Table of Contents
milleteknik 350-164 Voltage Converter 24V-12V 6A
Product Description
The Voltage Converter 24V-12V 6A is an optional card designed to convert 24V input voltage to 12V output voltage. It features load output, a heatsink for cooling, control terminals for managing output, dual 24V inputs, and indicator LEDs.
Mounting Instructions
- Ensure the cooling flange has free airflow of at least 50mm and is oriented upwards.
- Avoid laying cables over the heat sink.
- Mount the card in its plastic casing in a card slot within the enclosure, leaving space for cable connections.
- Install the board before wiring or commissioning.
Connection of Load
- Connect the load wiring to the load output terminals.
- Connect the control signal to the specified terminals.
- Refer to the battery backup manual for enabling battery backup.
- Ensure the load does not exceed 6.5A and the average current remains below 80% of the total maximum load.
FAQ
Q: What is the maximum load capacity of the Voltage Converter?
A: The maximum load capacity is 6A. Ensure that the load does not exceed this limit to prevent damage to the card.
Q: Where is the Voltage Converter manufactured?
A: The Voltage Converter is manufactured in Milleteknik’s factory in Partille, Sweden.
TECHNICAL SPECIFICATIONS
- Voltage converter 24-12V 6A is an optional card to convert 24 V to 12 V.
CAUTION
- ATTENTION! Heat source on the card!
- Cooling flange must sit with free air flow (at least 50 mm) and upwards.
- Cables must not be laid over the heat sink.
MOUNTING IN BATTERY BACKUP
- The card is delivered mounted in its plastic casing, for easy installation.
- If the card has come loose, snap it back into the plastic casing.
- Mount the card on any card slot in the enclosure, leaving space for cables.
- IMPORTANT Install the board before screwing on wiring or commissioning.
| Letter | Explanation | Comment |
|---|---|---|
| A | Optional card | The optional card comes mounted on plastic housing from the |
factory. Has it come loose? Snap it back on before mounting the card.
B| Plastic casing| The plastic casing has hooks for attaching slots in the
plate.
C| A place for the plastic casing| Slits in the sheet metal to snap the
plastic bracket.
CARD DESCRIPTION
| No | Explanation |
|---|---|
| 1 | Load output 12 V -/+ |
| 2 | Heatsink. Must sit with free air flow (at least 50 mm). Cables must not be |
laid over the heat sink.
3.1| CTRL +.Low (0) in turns off output.
3.2| CTRL -. High (1) in turns off output.
4.1, 51| 24 V in -, dual inputs, use any.
4.2, 52| 24 V in +, dual inputs, use any.
6| Green LED, lights up when incoming power is connected.
7| The green indicator lights up when the output is connected.
CONNECTION OF LOAD
CAUTION Connect load before commissioning battery backup.
- Connect load wiring to load output.
- A control signal is connected to 3.1, 3.2 (terminal CTRL).
- Enable battery backup. See the battery backup manual.
CAUTION
- Maximum load is 6 A, the card’s load must not exceed 6.5 A.
- The average current must never exceed 80% of the total maximum load.
TECHNICAL DATA
| Article name | Voltage converter 24V-12V 6A |
|---|---|
| Article number 24-12V | A-VC002406A01LM01 |
| Article number 24-9V | A-VC002406A02LM01 |
| Article number 24-15V | A-VC002406A03LM01 |
| Product Description | Voltage converter 24 V to 12 V. |
| Measure | 85 x 37 mm. |
| Power (card) consumption | 20mA |
| Entrances | Two entrances. (For alternative power supply when changing the |
power supply unit. In order not to interrupt the load voltage.) A terminal can
be used as a jumper to the next optional card, (only if the battery backup has
room for two cards).
Voltage in| 24 V
Voltage out| 12 V (Alternative output voltage (9 V-15 V) can be configured
from the factory, cannot be set afterwards)
Outputs| A cargo outlet. Controllable via CTRL (input).
Fuses| Output is currently limited, so no load fuse is needed.
Max load| 6 A in total. The average current must never exceed 80% of the
maximum load.
Indication| The green indicator lights up when the output is connected.
Green LED, lights up when incoming power is connected.
- Manufactured in Milleteknik’s factory in Partille, Sweden.
About the translation of this document
- The user manual and other documents are in the original language in Swedish. Other languages are machine-translated and not reviewed, errors may occur.
ADDRESS AND CONTACT DETAILS
- Milleteknik AB
- Ögärdesvägen 8 B
- S-433 30 Partille
- Sweden
- +46 31 340 02 30
- info@milleteknik.se
- www.milleteknik.com
Documents / Resources
|
milleteknik 350-164 Voltage Converter 24V-12V
6A
[pdf] Instruction Manual
350-164 Voltage Converter 24V-12V 6A, 350-164, Voltage Converter 24V-12V 6A,
Converter 24V-12V 6A
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>