REDODO 160Ah Lithium Battery Instruction Manual

PRODUCT MANUAL
Lithium Iron Phosphate Battery

160Ah Lithium Battery

128V
200Ah (100A BMS)

Product Overview
Combination: 12.8V 200Ah
Dimension: L21*W8.2″H8.5 inch
Plastic Shell Color: Grey + White

  www.redodopower.com
 service@redodopower.com
 technicalsupport@redodopower.com

Product Overview

12.8V 200Ah Battery
Operating Voltage: 12.8V
Charging Voltage: 14.410.2V
Recommend Charge Current: 40A (0.2C)
Max Continuous Discharge Current: 100A
Max Continuous Load Power: 1280W

Additional Components

M8-5/8″ (16mm) Terminal Bolts
The terminal bolts are used to secure multiple cable lugs to a single battery terminal. The bolts can be replaced with M8 bolts of other lengths based on actual needs.
Insulating Caps for Bolts

BATTERY-PACK MAIN PARAMETERS

1532 W207 H215 mm
Housing Material| ABS (Flame Retardant Plastic)
Protection Class| 1P65
Temperature Range| Charge: 0°C to 50°C / 32°F to 122°F
Discharge: -20°C to 60°C / -4°F to 140°F
Storage: -10°C to 50°C / 14°F to 122°F

HOW TO ESTIMATE THE BATTERY CAPACITY

STATE OF CHARGE (SOC)
The battery capacity could be roughly estimated by its resting voltage (not charging/discharging voltage)®.
Since the voltage of each battery is slightly different, and the voltage measurement is affected by the measuring instrument, ambient temperature, etc., the following parameters are for reference only.
The actual SOC of the battery is based on the discharge capacity under load.
Resting Voltage:The voltage is measured after the battery has been disconnected from the charger and loads with zero current, and left alone for 3 hours.

① Based on the characteristics of LiFePO4 batteries, the voltage measured by all LiFePO4 batteries during charging/discharging is not the real voltage of the battery. Therefore, after charging/discharging and disconnecting the battery from the power source, the voltage of the battery will gradually drop/increase to its real voltage.

SERIES / PARALLEL CONNECTION

THE PREMISE OF CONNECTION
To connect in series or /and parallel, batteries should meet the below conditions:
a. identical batteries with the same battery capacity (Ah) and BMS (A);
b. from the same brand (as lithium battery from different brands has their special BMS);
c. purchased in near time (within one month).

LIMITATION FOR SERIES/PARALLEL CONNECTION
Support connecting up to 16 identical batteries for up to:
4 in series as 48V (51.2V) battery system/
4 in parallel as 800Ah battery system.

WHAT TO DO WHEN THE BATTERY STOPS WORKING?

It has 85% chances that BMS has shut it off for protection, and you could try one of below ways to activate the battery.
General Steps
If the BMS has cut off the battery for protection, follow the below steps to activate it.

| Cut off all the connections from the battery
---|---
Leave the battery aside for 30mins
Then the battery will automatically recover itself to normal voltage (>10V) and can be used after fully charged.

If the battery is unable to recover itself after the above steps, please try activating by ONE OF BELOW TWO METHODS.
After activated (voltage > 10V) and fully charged by the normal charging method, it can be used normally.

1. Method
   Use a charger with lithium battery activation function to fully charge the battery.

2. Method
   Connect a controller that supports 12V LiFePO4 battery charging to charge the battery for 3~10s in sunny daytime.

PROVIDER
Shenzhen Maicheng Technology Innovation Co., Ltd.
MANUFACTURER CONTACT
service@redodopower.com
technicalsupport@redodopower.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>