ANKER Nebula Capsule 3 Laser User Guide

: June 3, 2024
: Anker

Table of Contents

ANKER Nebula Capsule 3 Laser
At a Glance
Remote Control
- Charge Your Projector
Use as a Projector
Important Safety Instructions
FCC Statement
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ANKER Nebula Capsule 3 Laser

anker nebula capsule 3 laser

At a Glance

Front View
Rear View
Top View
Bottom View

Remote Control

Overview

anker nebula capsule 3 laser-5

Prepare the Remote Control

For first-time use, slide to open the battery compartment, and install two AAA batteries.
To replace the batteries, slide off the battery compartment backplate, insert new batteries (matching the polarity ( +/- ) as indicated), and close the battery compartment.

Charge Your Projector

For first-time use, fully charge the built-in battery using the provided adapter.

Power On

Press and hold for seconds to power on the projector.

Enable Autofocus

Slightly move the projector to enable autofocus and auto keystone correction.
Press and hold for seconds to enable autofocus.

Basic Setup

For first-time use, follow the on-screen instructions to complete the basic setup. Adjust settings in the projector’s Settings menu if necessary.

Use as a Projector

Screen Mirroring

Wirelessly cast movies, games, and music from your phone to Nebula Capsule 3 Laser.

Play a video clip on your phone and tap the cast icon on the video screen.
Select the device D2426. The projector will mirror the screen of the connected phone.

Make sure Nebula Capsule 3 Laser and your phone are connected to the same wireless network.

Play from HDMI Playback Devices

Connect to HDMI playback devices such as a TV box, TV stick, DVD player, set- top box (STB), or gaming consoles.

Play Through External Sound Devices

Play from a USB Drive

Connect to a USB-A drive (with the USB converter) or USB-C drive to enjoy stored music, video, and pictures.

Use as a Bluetooth Speaker

Press to switch to Bluetooth speaker mode and select Nebula Capsule 3 Laser to connect.

Nebula Connect App

Download the Nebula Connect app for the best projector experience.

Important Safety Instructions

Due to the enclosure material, the product must only be connected to a USB 2.0 or higher.
The adapter shall be installed near the product and shall be easily accessible.
Please ensure you use only the adapter offered by the manufacturer. Using unauthorized adapter may cause danger and violate the authorization of the product and the guarantee article.
Do not use the product in an environment where the temperature is too high or too low. Never expose the product to strong sunshine or wet environments.
It is recommended to supply the product in an environment with a temperature that ranges from 5°C-25°C.
When supplying, place the device in an environment that has a normal room temperature and good ventilation.
Possibly hazardous optical radiation emitted from this product may be harmful to the eyes. Do not stare at operating beam.
Potential hazards may exist during lamp or product servicing.
Service shall be performed only by authorized, trained servicing, trained servicing personnel.
Do not open the enclosure of the product.
When the enclosure of the product is damaged, please do not use it anymore.
Do not open the enclosure of laser module inside the product.
When the enclosure of laser module inside the product is damaged, please do not use it anymore.
Laser inside, be aware of the risk of skin or corneal burns.
Do not use the product in any way other than described herein in order to avoid personal injury or property damage.
User should comply with the laws and regulations of the corresponding countries and regions where the equipment is located (used), abide by professional ethics, pay attention to safety obligations, and strictly prohibit the use of our products or equipment for any illegal purposes. Our company will not be responsible for any violators’ legal liability under any circumstances.

Warning:

Replacement of a battery with an incorrect type that can defeat a safeguard;
Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion;
Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas; and
A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.

Attention:

Remplacement d’une batterie par un type incorrect pouvant supprimer une protection;
Mise au rebut d’une batterie dans un feu ou dans un four chaud, ou écrasement mécanique ou coupure d’une batterie, susceptible de provoquer une explosion;
Maintien d’une batterie dans un environnement à très haute température pouvant provoquer une explosion ou la fuite de liquide ou de gaz inflammables; et
Batterie soumise à une pression de l’air extrêmement faible pouvant provoquer une explosion ou la fuite de liquide ou de gaz inflammables.

CAUTION : RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

ATTENTION RISQUE D’EXPLOSION SI LA BATTERIE EST REMPLACÉE PAR UN TYPE INCORRECT. ÉLIMINER LES BATTERIES USÉES SELON LES INSTRUCTIONS

Notice (Europe and United Kingdom)

This product complies with the radio interference requirements of the European Community.

Declaration of Conformity
Hereby, Anker Innovations Limited declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. For the Declaration of Conformity, visit the Web site https://uk.seenebula.com/.

This product complies with the radio interference requirements of the United Kingdom.

Declaration of Conformity
Hereby, Anker Innovations Limited declares that this device is in compliance with Radio Equipment Regulations 2017(SI 2017/1206). The full text of the UK declaration of conformity is available at the following internet address: https://uk.seenebula.com/.

The suitable temperature range for the projector and its accessories is 0°C-25°C.
The adapter is for indoor use only. The adapter type is PN4531 (with rated output voltage / current of 5VDC/3A or 9VDC/3A or 12VDC/3A or 15VDC/3A or
20VDC/2.25A) or A2713 (with rated output voltage / current of 5VDC/3A or 9VDC/3A or 15VDC/3A or 20VDC/3.25A).

RF exposure information
The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20 cmbetween the device and the human body. To maintain compliance with RF exposure requirement, use product that maintain a 20cm distance between the device and human body.

Frequency bands and power as below:

Function	Bands	Operation Frequency	Max.Power
Bluetooth (Projector)	2.4 GHz	2402-2480 MHz	EIRP 8.0 dBm

WIFI

(Projector)

| 2.4 GHz| 2412-2472 MHz| EIRP 19 dBm

5 GHz

5150~5350 MHz can be used indoors only.

The following importer is the responsible party (contract for EU matters):
Anker Innovations Deutschland GmbH I
Georg-Muche-Strasse 3, 80807 Munich, Germany
The following importer is the responsible party (contract for UK matters):
Anker Technology (UK) Limited I GNR8, 49 Clarendon
Road, Watford, Hertfordshire, WD17 1HP, United Kingdom

Your product is designed and manufactured with high quality materials and components, which can be recycled and reused.

This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health, and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product.

Notice (United States of America)

FCC Statement

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
(1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio/TV technician for help.

FCC Radio Frequency Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/mobile exposure condition. The min separation distance is 20cm.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations.
The following importer is the responsible party.
Company Name: Fantasia Trading LLC
Address: 5350 Ontario Mills Pkwy, Suite 100, Ontario, CA
91764
Telephone: 1-800-988-7973
Notice (Canada)

IC Statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

this device may not cause interference, and
this device must accept any interference, including interference that may cause undesired operation of the device.

IC RF Statement
When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements.

Notice (Republic of Korea)

The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and anyuse of such marks by Anker Innovations Limited isunder license. Other trademarks and trade names are those of their respective owners.

HDMI, and HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC in the United States and other countries.

Manufactured under license from Dolby Laboratories.
Dolby, Dolby Audio, and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation

Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road,Mongkok, Kowloon, Hong Kong

RG1 IEC 62471-5:2015
Complies with IEC 60825-1:2014 Class 1 and IEC 62471-5:2015 Risk Group 1