VICTOR VLINK V430B Digital Pest Management User Guide

VICTOR VLINK V430B Digital Pest Management

OVERVIEW

ACCOUNT SET-UP

1. Before you begin, confirm that you have a VLINK account created and an Admin has added you to the account. Contact your VLINK sales representative for confirmation if you are unsure.
2. Confirm that you can successfully log-in at www.app.digitalpestmanagement.com.

CONNECT THE GATEWAY

Plug in the gateway.

For all other gateway instructions, contact your VLINK Sales Representative.

DOWNLOAD THE APP

1. Search for the Victor VLINK Digital Pest Management app from the Apple App Store or Google Play Store and download to your device.
   
   

2. Log-in using your VLINK account credentials

3. Follow the VLINK site setup to ensure your deployment site is correctly set up in the VLINK app.

CONNECT TRAP TO THE NETWORK

1. Remove the plastic battery pull tab at the front end of the trap.
2. Press the power button to turn the trap on.
3. You will see three green LED lights indicating that the trap is on.
4. Follow the steps in the VLINK app to add the trap to the site.

LED Light Sequences

• 3 quick green flashes – trap powering on
• 3 quick red flashes – trap powering off
• 3 long green flashes – LoRa message successfully sent
• 1 long orange flash – trap is set
• 2 quick orange flashes – trap going into sleep mode

BAIT TRAPS

Paste Baits

1. Place paste baits in the bait cup container.
2. Ensure bait is firmly in cup to prevent it from being pulled out easily by the rodent.
3. Placing bait on the trigger petal may lead to non-capture triggers.
   

Tied Baits

1. Tie desired bait to raised Victor® V.
2. Orient bait towards middle of trap pedal.

After Baiting
Pull back using thumb grips to set the trap. You will see 1 long orange flash to indicate trap is set, immediately followed by three long green flashes to indicate a message has been sent.

Note: Setting the trap can only be accomplished if the trap is level. If it is tilted significantly, it will not set.

PLACE TRAP

Once your trap is connected, place it in the area of rodent activity and wait for the trap to alert you of a capture.

RESET TRAP AFTER A KILL

1. If a rodent has been captured, record your kill data using the VLINK Mobile App.
2. Once the rodent is removed, the trap is ready to be baited and reset for another capture.
3. To reset, simply pull the kill bar back to the set position and wait for the three green LED flashes to let you know the trap is communicating and ready for another kill.
4. The trap must send a message for the kill notification to clear.

Pro Tip: Avoid using strong cleaning products on the traps. A captured rodent can leave behind scent and odor that can make the trap more attractive to other rodents.

FCC

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (ll this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this device not expressly approved by Woodstream Corporation could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses. and can radiate radio frequency energy and. if not installed and used in accordance with the instructions. may cause harmful interference to radio communications. However. there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

IC

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

RF Exposure

This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

Manufactured for: Wood stream Corporation 69 N. Locust Street. Lititz, PA 17543 • 800-800-1819

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>