Amica OKP6552SB, OKP6552SW, OKP9552SB Kitchen Extractor Hood Instruction Manual
- June 9, 2024
- Amica
Table of Contents
OPERATING INSTRUCTIONS Kitchen extractor hood
OKP6552SB / OKP6552SW / OKP9552SB
OKP6552SB, OKP6552SW, OKP9552SB Kitchen Extractor Hood
Dear customer,
From now on, your daily housework will be easier than ever before. Your
appliance Amica is exception- ally easy to use and extremely efficient.
After reading these Operating Instructions, operating the appliance will be
easy.
Before being packaged and leaving the manufacturer, the appliance was
thoroughly checked with regard to safety and functionality.
Before using the appliance, please carefully read these Operating
Instructions. By following these instructions carefully you will be able to
avoid any problems in using the appliance. It is important to keep these
Operating Instructions and store them in a safe place so that they can be
consulted at any time.
Follow these instructions carefully in order to avoid possible accidents.
Sincerely, Amica
NOTES ON SAFETY
-
Before using the appliance, please carefully read this manual!
-
The appliance is designed for household use only.
-
The manufacturer reserves the right to introduce changes, which do not affect operation of the appliance.
-
The manufacturer shall not be liable for any damage or fire caused by the appliance resulting from failure to follow instructions in this manual.
-
Cooker hood is designed to remove cooking odours. Do not use cooker hood for other purposes.
-
Connect the cooker hood operating in extraction mode to a suitable ventilation duct (do NOT connect the cooker to smoke or flue gas ducts, which are in use). It requires installation of the air extraction duct to the outside. The length of the duct (usually a pipe of Ø 120 or 150 mm) should not be longer than 4-5 m. An air extraction duct is also required for telescopic and furniture hoods in absorption mode.
-
Cooker hood operating in air recirculation mode requires the installation of an activated charcoal filter. In this case, installing an extractor duct is not required, however it is recommended to install an air guide vane (Mainly in chimney cooker hoods).
-
The cooker hood features independent lighting and exhaust fan that can be operated at one of several speeds.
-
Depending on the type, the hood is designed to be permanently attached to a vertical wall over a gas or electric stove (chimney and universal hoods); on the ceiling over a as or electric stove (island hoods); on the vertical built in furniture over a gas or electric stove (telescopic and built- in hoods). Before installing, make sure that the wall/ceiling structure is strong enough to suspend the hood. Some hoods are very heavy.
-
For details of the installation distance above an electric hob please refer to product technical sheet If the installation instructions of the gas cooker specify a greater distance, this must be taken into account (Fig. 1).
-
Do not leave an open flame under the hood.
When the pots are removed from the burner, set the minimum flame. Always make sure that the flame does not extend outside the pot, because it causes unwanted loss of energy and a dangerous concentration of heat. -
When cooking on fat, supervise the pans constantly, because overheated fat can ignite.
-
Unplug the appliance before any cleaning, replacing the filter or repair work.
-
Cooker hood grease filter should be cleaned at least once a month, because the filter saturated with fat is flammable.
-
Ensure adequate ventilation (air flow) if other equipment such as liquid fuel stoves or heaters are operated in the room in addition the cooker hood. When the cooker ood is simultaneously operated with burning appliances requiring adequate fresh air from the room to work properly, their safe operation is possible if under pressure around these appliances is a maximum of 0.004 mbar (this does not apply when the cooker hood is used as an odour filter)
-
Do not lean on the hood.
-
The hood should be cleaned regularly both inside and out (AT LEAST ONCE A MONTH, following the indications concerning maintenance provided in this manual)..Failure to adhere to the rules concerning cleaning the hood and replacing filters results in a fire risk.
-
If the power cord is damaged it should be re- placed by a specialised service centre.
-
Ensure that it is possible to disconnect the appliance from the mains by removing the plug or switching off the bi-polar switch.
-
This appliance is not intended for use by persons (including children) with physical, mental or sensory handicaps, or by persons inexperienced or unfamiliar with the appliance, unless under supervision or in accordance with the instructions as communicated to them by persons responsible for their safety.
-
Particular attention should be paid not to allow unaccompanied children to use the appliance.
-
Make sure voltage indicated on the nameplate corresponds to the local mains supply voltage.
-
Before use, extend and straighten the power cord.
-
Packaging materials (bags, polyethylene, polystyrene, etc.) should be kept away from children during unpacking.
-
Before connecting the hood to the mains power supply always check that the power cord is properly installed and is not trapped by the appliance. Do not connect the appliance to the mains until assembly is complete.
-
Do not operate your kitchen hood without the al- uminium grease filters.
-
It is strictly forbidden to cook dishes nder on an open flame (flambé) under your kitchen hood.
-
Always strictly adhere to regulations issued by the competent local authorities regarding the technical and safety requirements for fume extraction.
-
Failing to tighten bolts and fasteners in accordance with these instructions may endanger life and health.
-
Hanging kitchen hoods operate only in air circu- lation / odour absorber mode
-
WARNING! Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards.
UNPACKING
** During transportation, protective packaging was used to protect the
appliance against any damage. After unpacking, please dispose of all elements
of packaging in a way that will not cause damage to the environment. All
materials used for packaging the appliance are environmentally friendly; they
are 100% recyclable and are marked with the appropriate symbol.
Important!** Packaging materials (bags, polyethylene, polystyrene, etc.)
should be kept away from children during unpacking.
DISPOSAL OF OLD APPLIANCE
In accordance with European Directive 012/19/EU and local legislation
regarding used electrical and electronic goods, this appliance is marked with
the symbol of the crossed-out waste container. This marking indicates that the
appliance must not be disposed of together with other household waste after it
has been used. The user is obliged o hand it over to waste collection centre
collecting used electrical and electronic goods. The collectors, including
local collection points, shops and local authority departments provide
recycling schemes.
Proper handling of used electrical and electronic goods helps avoid
environmental and health hazards resulting from the presence of dangerous
components and the inappropriate storage and processing of such goods.
OPERATION
Cooker hood controls
Control Panel is shown in Figure 4, for reference it is also shown
below:
The control panel is equipped with touch controls: Control functions are
described below:
3- Off-Timer sensor
4- Reduce fan speed sensor
5- Increase fan speed sensor
6- Display
7- Ozone generator on/off
8- Light control sensor
9- StandBy mode sensor
When you plug in your appliance , will be shown on the display for a fraction
of a second, then the display will go off. Touch to activate the appliance —
the pictogram will light up When activated, touch + to start the fan.
Available fan speeds:
- Low speed (1). Use this speed when cooking a little food with hardly any fumes.
- Medium speeds (2 – 3). Use this speed when cooking multiple dishes at the same time with moderate amount of fumes.
- Turbo ( ) — use this speed when frying or grilling with large amount of fumes.
Use the + and – sensors to increase or reduce fan speed.
Note: The Turbo speed is active only for 5 minutes (the dot on the
display flashes), then the fan speed will be reduced. Turbo speed operation is
time limited. By activating the Turbo speed again and again, you can use it
for a maximum of 30 minutes (including the Turbo off intervals if shorter than
5 minutes). After this time, Turbo speed will not be available for the next 30
minutes — during this time, the maximum possible fan speed is 3.
To turn off the fan, touch repeatedly until fan speed is reduced to zero , or
touch .
Touch to turn the lighting on. Touch again to turn the lighting off.
The lighting operates independently of the on/off sensor.
Off-Timer
Use Off-Timer to turn off the hood after a specified time. Use Off-Timer to
filter the fumes out of the air after cooking. The Off-Timer can be set to 5,
10 or 15 minutes. Touch to activate the Off-Timer at any time.
The sensor will flash and the display will show . Now use the – and + sensors
to select the Off-Timer delay:
| Display indication | Delay time [min] |
|---|---|
| 15 | |
| 10 | |
| 5 |
Touch to confirm your Off-Timer setting (according to the above table). A flashing dot will appear by the fan speed on the display and the sensor will flash. Touch to deactivate the Off-Timer at any time — the dot by the fan speed and will stop flashing.
The ozone generator
When this function is active, ozone is generated. Ozone has bactericidal,
viricidal and fungicidal properties, it destroys mites and germs. In addition,
it removes and neutralizes organic and inorganic odours and disinfects rooms.
Thanks to ozone, the odours of cooking and frying are removed faster and more
effectively.
The ozone generator function can be used independently of the kitchen hood
operation in the air extraction or the recirculation mode.
The ozone generator function is only available when the hood fan operates.
The ozone is emitted by the kitchen hood in regular cycles, programmed in such
a way that the ozone concentration does not exceed the permissible and safe
doses, ensuring full safety of use.
NOTE! Before using the ozone generator function for the first time, set the
appropriate ozonation programme, adapted to the size of the room (for open
kitchens, the kitchen area with the directly connected room should be taken
into account) to avoid the risk of a high ozone concentration, which can be
harmful to health.
In order to set the appropriate ozonation programme:
- Touch to activate the appliance and will be shown on the display.
- Touch and hold the sensor for 8 seconds, and the display will show the number 1, 2 or 3, which will reflect the currently set programme.
- Now use the – and+ sensors to select the desired ozonation programme suitable for the room size:
Display indication| The surface area of the room where the ozone generator
function is used [m²]
---|---
| < 6m²
| 6-10m²
| > 10m²
• Touch again to confirm your choice and will be shown on the display.
The selected ozonation programme is stored and will not be lost even in the
event of a power outage.
When the suitable ozonation programme is set you can start using the ozone
generator function. To do this, turn on the kitchen hood and set any fan
speed. Touch to activate the ozone generator function. You can smell ozone in
the air much like just after the storm. Touch the sensor again to turn off the
ozone generator function.
This function deactivates automatically after 3 hours or when you turn off the
fan.
Note: If the ozone generator operation is turned off for more than 40 minutes,
and you re-activate the ozone generator, the cycle will be restarted rather
than resumed (the time the function operated before will not be taken into
account).
Excessive concentration of ozone in the air is harmful to health, therefore
use the suitable programme, and also, please observe these guidelines:
- Do not inhale the ozone directly from ozone generator housing outlets.
- Do not obstruct or block the air outlet grilles,
- Ozone generator function must not be used by persons suffering from olfactory disorders.
Other important information concerning the operation of the hood
Operation in air circulation / odour filter mode. In this mode, the filtered
air returns to the room through the outlets. Install activated charcoal filter
in this setting. It is recommended to install the air guide (available
depending on the model, mainly in chimney cooker hoods). Air extraction
operation: When cooker hood operates in extraction mode, air is discharged
outside through an extraction duct. Remove activated charcoal filter in this
setting. The cooker hood is connected to the air outlet opening using a rigid
or flexible extraction duct with a diameter of 150 or 120 mm, and the
appropriate clamps, which must be purchased at a hardware store. The appliance
should be installed by a qualified installer.
Fan speed: Lowest and medium fan speed is used in normal conditions and less
intense odours, while the highest speed is used only when cooking odours are
very intense, such as during frying or grilling. Note (applies to universal
hoods only): Due to the esign of universal hoods you need to manually change
the mode of operation. See Figure 8 for instructions on how to change the
mode.
Note (only applies to telescopic and in-built kitchen hoods): Furniture and
telescopic cooker hoods operating in air recirculation mode require
installation of the exhaust duct. The other end of the duct should be directed
to the room as it will discharge filtered air.
Note: Hanging kitchen hoods operate only in air circulation / odour absorber
mode
CLEANING AND MAINTENANCE
Maintenance
Regular maintenance and cleaning of the appliance will ensure trouble-free
operation of the cooker hood and extend its life. Especially make sure that
the grease filter and
activated charcoal filter are replaced according to manufacturer’s
recommendations.
- Do not use a soaked cloth, sponge, or water jet.
- Do not use solvents or alcohol, as they may tarnish lacquered surfaces.
- Do not use caustic substances, especially for cleaning stainless steel.
- Do not use a rough or abrasive cloth.
- It is recommend to use a damp cloth and a neutral detergent.
Note: After several washes in the dishwasher, the colour of the aluminium
filter may change.
The change of colour does not indicate improprieties or the necessity to
change it.
Grease filter
For normal hood operation, grease filter should be cleaned every month in the
dishwasher or by hand using a mild detergent or liquid soap. Dismantling of
grease filter is shown on Figure 5. Acrylic filter is used in some models.
This filter should be replaced at least once every 2 months or more frequently
if the appliance is used intensively.
Activated charcoal filter
Charcoal filter is used only when the cooker hood is not connected to the
ventilation duct. Activated charcoal filter can absorb odours until saturated.
Charcoal filter is not suitable for washing or regeneration and should be
replaced at least once every 3-4 months or more frequently if the appliance is
used intensively.
Dismantling of charcoal filter is shown on Figure 6.
Light
Use incandescent / halogen / LED modules of the same specification as those
factory-installed in the appliance. See Figure 7 for details how to replace
lights. If there is no such figure in this manual, please contact authorised
service to replace the lighting module.
WARRANTY AND AFTER SALES SERVICE
Warranty
Warranty service as stated on the warranty card. The manufacturer shall not be
held liable for any damage caused by improper use of the product.
Service
- The manufacturer recommends that all repairs and adjustments be carried out by the Factory Service Technician or the Manufacturer’s Authorized Service Point. For safety reasons, repairs should be referred to professionals.
- Repairs carried out by unqualified persons may seriously endanger the appliance user.
- The minimum warranty period for the appliance offered by the manufacturer, importeror authorized representative is given in the warranty card.
- The warranty shall be void if you make any independent adaptations or alterations, tamper with seals or other appliance safety devices or its parts or interfere with the appliance contrary to operating instructions.
In the event of appliance malfunction, request assistance or repair.
If your appliance needs repair, please contact the service centre.
Please see warranty card for address and contact details of our service
centre. Before contacting us, please have ready the appliance serial number,
which can be found on the identification sticker: For your convenience, please
write it down below:
Manufacturer’s Declaration
The manufacturer hereby declares that this product meets the requirements of
the following European directives:
- Low Voltage Directive 2014/35/EC
- Electromagnetic Compatibility (EMC) Directive 2014/30/EC
- ErP Directive 2009/125/EC
- Directive RoHS 2011/65/E C
and has thus been marked with the ****symbol and been issued with a
declaration of compliance made available to market regulators.
Amica S.A.
ul . Mickiewicza 52 / 64-510 Wronki
tel. 67 25 46 100 / fax 67 25 40 320
www.amica.pl
Amica International GmbH
Lüdinghauser Str. 52
D-59387 Ascheberg
Tel: 0 25 93 – 95 67-0
www.amica-group.de
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>