Shark Sonic Duo KD401T Hard Floor Cleaner User Manual

Shark Sonic Duo KD401T Hard Floor Cleaner User Manual

OWNER’S GUIDE

SONIC DUO™ Wood & Hard Floor Cleaner

KD401T

IMPORTANT SAFETY INSTRUCTIONS

For Household Use Only

WHEN USING YOUR SHARK® SONIC DUO™, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:

READ ALL INSTRUCTIONS BEFORE USING YOUR SHARK® SONIC DUO™ Wood & Hard Floor Cleaner.

POLARIZED PLUG:
This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.

CAUTION:
Keep all Shark® branded cleaners and polishes out of the reach of children.
Eye irritant. Should some of the Shark® branded cleaners and polishes be rubbed or splashed into the eyes, wash out thoroughly with water. If irritation continues, contact a physician.
In case of ingestion, drink 16 FL. oz. (2 cups) of water.

WARNING:

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:

1. Use the system only for its intended use.
2. DO NOT use outdoors.
3. DO NOT leave the appliance unattended when plugged in. Always turn the appliance off (O) and unplug the power cord from the electrical outlet when not in use and before servicing.
4. Turn off all controls before unplugging.
5. DO NOT allow the appliance to be used by children. Close attention is necessary when used by or near children, pets or plants.
6. Use only as described in this manual.
7. Use only manufacturer’s recommended accessories.
8. DO NOT use with damaged cord or plug. If the appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return the appliance to EURO-PRO Operating LLC for examination and repair. Incorrect re-assembly or repair can cause a risk of electrical shock or injury to persons when the appliance is used.
9. To protect against a risk of electric shock, DO NOT immerse the appliance into water or any other liquids.
10. DO NOT handle the plug or the appliance with wet hands or operate the appliance without shoes.
11. DO NOT pull or carry by cord, use the power cord as a handle, close a door on the cord, or pull the cord around sharp edges or corners. Do not run the appliance over the power cord. Keep the power cord away from heated surfaces.

12. DO NOT unplug by pulling on the power cord. To unplug, grasp the plug not the power cord. Do not use extension cords or outlets with inadequate current carrying capacity.
13. DO NOT use for space heating purposes.
14. DO NOT put any objects into openings. Do not use with any opening that is blocked.
15. DO NOT put hands or feet under the Sonic Duo™.
16. Keep hair, loose clothing, fingers, and all parts of the body away from openings and moving parts.
17. Use ONLY on flat, horizontal surfaces. Do not use on walls, counters or windows.
18. To reduce the risk of fire and electric shock – use ONLY Shark®’s cleaning and polishing solutions intended for use with this appliance.
19. DO NOT add any cleaning solutions in the Shark® Sonic Duo™ other than Shark®’s Wood & Hard Floor Cleaner. The Wood & Hard Floor Polish should never be run through the Sonic Duo™. It will cause clogging. Use of other scented perfumes, oils or any other chemicals added to the solution or to the Reusable Bottle used in this appliance may damage or clog the unit and void the warranty. If you live in a hard water area, we recommend using distilled water to dilute the Wood & Hard Floor Cleaner for better performance.

23. When cleaning the Sonic Duo™, unplug the power cord from the electrical outlet, and clean with a dry or damp cloth. Do not pour water
or use alcohol, benzene or paint thinner on the unit.
24. Unplug the appliance before attaching or removing the pads.
25. Extreme caution should be exercised when using this appliance to clean stairs.
26. Never use the Sonic Duo™ without the Hard Floor Cleaning Pad or Hard Floor Polishing Pad attached.
27. Keep your work area well lit.
28. Store the Sonic Duo™ indoors in a cool, dry place.
29. To avoid circuit overload, do not operate another appliance on the same socket (circuit) as the Sonic Duo™.
30. If an extension cord is absolutely necessary, an extension cord rated a minimum of 15 ampere, 14 gauge cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange cord so that it cannot be pulled or tripped over.
31. This appliance is provided with double insulation. Use only identical replacement parts. See instructions for servicing of double-insulated appliances.

WARNING: Your SONIC DUO™ is designed to clean hard floor surfaces. Do not use on wood or tile floors that are highly worn, unfinished or have a wax or oil finish. Surfaces that have been treated with wax or some no wax floors may be damaged by the cleaning and polishing solutions therefore it is always recommended to test an isolated area of the surface to be cleaned before proceeding. You should always check the use and care instructions from the floor manufacturer.

“SAVE THESE INSTRUCTIONS”

Servicing of double-insulated appliances:
A double-insulated appliance is marked with one or more of the following: The words “double-insulation” or “double-insulated” or the double insulation symbol (square within a square).

In a double-insulated appliance, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated appliance, nor should a means for grounding be added to the appliance. Servicing a double-insulated appliance requires extreme care and knowledge of the system, and should be done only by qualified service personnel. Replacement parts for a double-insulated appliance must be identical to the parts they replace.

This manual covers model numbers:
KD401T 26

TECHNICAL SPECIFICATIONS

Voltage: 120V~, 60Hz.
Power: 96 Watts
Reusable Bottle Capacity: 32 oz.

Thank you for purchasing the Shark® Sonic Duo™ Wood & Hard Floor Cleaner.

Getting Started

When assembling your Sonic Duo™ there may be a little water in the Reusable Bottle. This is because we test all of our products 100% before you buy them, so you get a quality Shark® Sonic Duo™ Wood & Hard Floor Cleaner.

a. Handle
b. Spray Button
c. On/Off Button
d. Sonic Duo™ Scrub Head
e. Spray Nozzle

f. Reusable Bottle for Hard Floor Cleaning Solution
g. Wood & Hard Floor Cleaner
h. Hard Floor Cleaning Pad
i. Wood & Hard Floor Polish
j. Hard Floor Polishing Pad

NOTE: Additional accessories such as cleaning pads and cleaning solutions are available for purchase at www.sharksonicduo.com or by calling 1-800-798-7398. A special tool that aids in the removal of scuff marks and polish touch ups is also available.

IMPORTANT: Always make sure that the Sonic Duo™ is UNPLUGGED from the wall when not in use. Never fill the Reusable Bottle, change or remove the Sonic Duo™ pad when the appliance is plugged into the wall. Use ONLY diluted Wood & Hard Floor Cleaner in the Sonic Duo™ Reusable Bottle. The addition of other chemicals or cleaning solutions may damage the appliance, void the warranty and could be unsafe for you and your family. For best results, dilute the Wood & Hard Floor Cleaner with distilled water to reduce streaking and minimize residue.

WARNING: The Wood & Hard Floor Polish should never be put through the Sonic Duo™. It will cause clogging in the system.

ASSEMBLY

1. Insert the handle into the neck of the main body of the Sonic Duo™. Push the mop handle and main body of the appliance together until you hear it “click” into place. (Fig. 1)

2. Hold the power cord and wrap it around the cord holders. (Fig. 2)

3. Place the Hard Floor Cleaning Pad or the Hard Floor Polishing Pad on the floor ensuring that the velcro side is facing up. (Fig. 3)

4. Place the Sonic Duo™ unit on top of the Hard Floor Cleaning Pad or the Hard Floor Polishing Pad. (Fig. 3)

Using Your Sonic Duo™ Wood & Hard Floor Cleaner

IMPORTANT : When cleaning, do not use the Sonic Duo™ without attaching a Hard Floor Cleaning Pad and adding the diluted cleaning solution to the Reusable Bottle first. When polishing, do not use the Sonic Duo™ without attaching a Hard Floor Polishing Pad.

Cleaning Your Hard Floors:

1. To remove the Reusable Bottle, hold it and pull it up to remove from the unit. (Fig. 4)

2. Remove the “Green” bottle cap. Add 1 part of the Sonic Activated Wood & Hard Floor Cleaner solution to 7 parts water into the Reusable Bottle. Use the measuring marks on the Reusable Bottle for easy measuring and filling. (Fig. 5) Always fill with cold water first up to the “Water Fill Line” and then the add the cleaning solution up to the “Solution Fill Line” to avoid foaming and to ensure accuracy.

3. Screw the bottle cap on tightly and insert the Reusable Bottle into the unit upside down. Push it down to make sure that it is well inserted. You will hear an audible “Click” when the Reusable Bottle is inserted properly. (Fig. 6)

IMPORTANT: Do not use on unsealed wood or unglazed ceramic floors. Do not use on wood or tile floors that are highly worn, unfinished or have a wax or oil finish. Surfaces that have been treated with wax or some no wax floors may be damaged by the cleaning and polishing solutions therefore it is always recommended to test an isolated area of the surface to be cleaned before proceeding. You should always check the use and care instructions from the floor manufacturer.

IMPORTANT: Make sure the floors are swept or vacuumed before using the Sonic Duo™.
Visit www.sharkcleancom for other great quick cleaning products to complement your Sonic Duo™, such as the Shark® Rotator™ vacuums.

4. Twist the quick release cord holder to unwrap the power cord completely. (Fig. 7)
Plug into an electrical outlet and slide the “On/Off” button down to turn the Sonic Duo™ on. (Fig. 8)

5. Make sure that the Hard Floor Cleaning Pad is attached to the Sonic Duo™. This pad has a “Green” trim and the tag says “Hard Floor Cleaning Pad”. Attach the side of the Cleaning Pad with the tag to the back of the Sonic Duo™. (Fig. 9)

Frequently Asked Questions

Q. My Sonic Duo™ leaves a foam on hard floors.
A. The Sonic Duo™ Hard Floor Cleaning Pad is likely too saturated. Replace it with a clean, dry pad.

Q. My floors appear cloudy after cleaning.
A. The Sonic Duo™ Hard Floor Cleaning Pad may be dirty. Change the pad.

OR

A. The Sonic Duo™ Hard Floor Cleaning Pad was washed with a powder detergent and may be damaged and require replacement. Never use powder detergents. Only use liquid detergent to launder the cleaning pads.

OR

A. The Sonic Duo™ may have been left in the same spot for too long with a wet cleaning pad. Never leave the unit with a wet pad in one spot for too long.

OR

A. This may be leftover from past cleaners that were used on the floor surface. Use the Sonic Duo™ a few more times and see if the leftover cloudiness is removed. If this does not work, we suggest rinsing the floor with water and letting it dry. One or more rinses generally removes the residue. A more stubborn case may require you to rinse the floor with a mix of one part vinegar to 2 parts water. Then use the Sonic Duo™ again with a clean pad.

IMPORTANT: NEVER add the Sonic Activated Wood & Hard Floor Polish to the Reusable Bottle or run it through the Sonic Duo™ unit.

Polishing Your Hard Floors:

1. Vacuum the floor to remove all loose dirt, dust and grit from the floor surface. For best results, we recommend that you clean the floor using the Shark® Wood & Hard Floor Cleaner first and allow time to dry before polishing.

2. Attach the Wood & Hard Floor Polishing Pad to

the bottom of the Sonic Duo™. This pad has a “Orange” trim and the “Orange” tag says “Hard Floor Polishing Pad”. (Fig. 12)

3. Lightly step on the back of the scrubbing head to release the handle.

WARNING: Never stand on the Sonic Duo™.

4. Carefully, squirt a liberal amount of the Floor Polish onto an area of the floor to be polished and place the polishing pad over it before you start the unit. Make sure that the polishing pad is saturated and then squirt the polish in 5’x5’ sections.

5. Turn the On/Off button to the“On (I)” setting.

Always squirt the floor polish from a height of 6 inches above the floor to avoid splashing the polish over the floor. One bottle is enough to cover 425 square feet. (Fig. 13)

NOTE: The 16 oz. polish bottle include with purchase is enough to cover 250 sq. ft.

6. Use the Sonic Duo™ to spread the polish evenly over the floor. Do not go over an applied area too frequently. Always leave an area looking wet. If a section begins to look dry while polishing, add more Wood & Hard Floor Polish to the area. Repeat until the whole area has been polished.

7. When going from section to section, do not lift the Sonic Duo™ to move it, always slide it to the next section. No rinsing is required.

8. Allow the Wood & Hard Floor Polish to dry for at least 1 hour in light traffic areas and a complete 24 hours for the polish to cure before returning to heavy traffic areas.

9. When finished, turn the unit off and slide and lift the Sonic Duo™ to remove it from the area that was just polished. Lay the Sonic Duo™ on its side and remove the Hard Floor Polishing Pad by hand. (Fig. 14)

NOTE: Depending on the amount of traffic your floors sustain, Shark® recommends polishing every 2 months. Touch up high traffic areas as needed in- between full floor polishes.

IMPORTANT: Do not use on unsealed wood or unglazed ceramic floors. Do not use on wood or tile floors that are highly worn, unfinished or have a wax or oil finish. Surfaces that have been treated with wax or some no wax floors may be damaged by the cleaning and polishing solutions therefore it is always recommended to test an isolated area of the surface to be cleaned or polished before proceeding. You should check the use and care instructions from the floor manufacturer before cleaning or polishing.

IMPORTANT: Do not use more than one brand of floor polish to polish one room. Use only Shark® Wood & Hard Floor Polish.

Frequently Asked Questions

Q. Polishing has left my floors streaky or spotty.
A. You should go over the streaky or spotty area with more polish. Always leave the area looking very wet, never dry.

Q. There is a footprint, smudge or uneven spot after or during polishing.
A. You should add more polish to any problem areas during polishing. Always leave the area looking very wet, never dry.

Q. I accidentally ran the Shark® Wood & Hard Floor Polish through the Sonic Duo™ and now it is not working properly.
A. Shark® Wood & Hard Floor Polish should always be squirted directly onto the floor . If it was run through the unit, you need to flush it out immediately. Fill the Reusable Bottle with warm water and spray it through the system to flush it. Then turn and remove the tip of the nozzle to clean it. Call Customer Service at 1-800-798-7398 for additional assistance if necessary.

General Tips:

• Change the Wood & Hard Floor Cleaning Pad frequently for best results.
• Always vacuum floors before cleaning or polishing.
• If you notice any uneven areas or streaking, DO NOT go over the same area with more polish if the floor has begun to dry. Wait until the floor polish has totally dried for approximately a day before going over it again with more polish.
• Never lift the Sonic Duo™ up at the end of a section of flooring that has been polished. Always slide the unit off the floor and then remove the pad.
• When polishing, you should always leave each section looking wet, never dry, before going to the next section.

AFTER USE AND STORAGE

1. When you have finished using the Sonic Duo™, unplug the cord from the outlet and remove the Hard Floor Cleaning Pad or Hard Floor Polishing Pad from the unit.

2. Store the Shark® Sonic Duo™ in the upright position without the Hard Floor Cleaning Pad or Hard Floor Polishing Pad on the unit and away from children or high traffic areas.

3. The Reusable Bottle can be hand washed ONLY. Never wash the Reusable Bottle in the dishwasher – it will warp.

CARE FOR YOUR HARD FLOOR CLEANING PAD AND HARD FLOOR POLISHING PAD

NOTE: Please note that the Hard Floor Polishing Pad must be rinsed immediately after use and before being machine washed with the other pads.

1. We recommend washing your Sonic Duo™ Hard Floor Cleaning Pads and Hard Floor Polishing Pads separately from other fabrics to avoid picking up lint. Only use liquid detergent (no powder detergent). Do not use any fabric softeners or bleach. Line dry or dry on a low dryer setting.

2. If there are loose threads on the cleaning or polishing pad, carefully cut the thread with scissors. Do not pull on them or cut at the base.

Ordering Replacement Parts

To order additional parts and accessories, feel free to contact us at www.sharksonicduo.com or call 1-800-798-7398.

NOTE: Some parts may be available at your local retailer. Contact customer service for any other servicing.

Troubleshooting Guide

is not firmly inserted into the unit. Make sure that you hear an audible “Click” when you insert the Reusable Bottle into the appliance.
2.   There may be air in the system. Hold down the spray button for 5 to 10 seconds to flush the system.
Sonic Duo™ doesn’t spray.| 1.   Make sure that the Reusable Bottle is inserted all the way in. You should hear an audible
“Click” when inserted.
2.   Check that there is enough cleaning solution in the Reusable Bottle. If not, add more.
3.   The bottle cap on the Reusable Bottle may need to be cleaned. Remove it from the Reusable Bottle and rinse it under running water and then replace it onto the Reusable Bottle.
4.   There may be air in the system. Hold down the spray button for 5 to 10 seconds until solution comes out of the spray nozzle.
Sonic Duo™ turns off when the handle is lowered.| 1.  The Sonic Duo™ automatically turns off when the handle is lowered to low. This is a safety mechanism to ensure that the machine will turn off if it is dropped. To keep the Sonic Duo™ on when cleaning under low profile items, simply twist the handle to the left or right and engage the swivel. When the handle is swivelled and lowered, the Sonic Duo™ will remain on.
The cap of the Reusable Bottle is stuck inside the Sonic Duo™ after the bottle was removed.| 1.  To remove the cap, hold center valve of the cap with your fingers and gently pull it out. If it doesn’t come out easily, use a set of long nose pliers for leverage. Be careful not to crack the center valve when applying pressure and lifting up.
Sonic Duo™ turns off on its own.| This unit is equipped with an automatic protector. If for some reason your appliance overheats, the protector will automatically turn the unit off. Should this occur, perform the following steps to restart the appliance:
1.  Move the switch to the “O” (Off) position.
2.  Unplug.
3.  Allow the unit to cool for around 45 minutes.
4.  Plug in.
5.  Turn the switch on to restart.
Note: If appliance still does not start, contact Customer Service at: 1-800-798-7398.

TWO (2) YEARS LIMITED WARRANTY

EURO-PRO Operating LLC warrants this product to be free from defects in material and workmanship for a period of two (2) years from the date of the original purchase, when utilized for normal household use, subject to the following conditions, exclusions and exceptions.
If your appliance fails to operate properly while in use under normal household conditions within the warranty period, return the complete appliance and accessories, freight prepaid. For assistance with warranty service options or customer support, please call our customer care and product specialists at , call 1 800-798-7398 or visit our website www.sharksonicduo.com.
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC will repair or replace it free of charge. Proof of purchase is required and a fee of $19.95 will apply to cover the cost of return freight. *

The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option. This warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes. This limited warranty does not cover damage caused by misuse, abuse, negligent handling or damage due to faulty packaging or mishandling in transit. This warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs, service or alterations to the product or any of its parts, which have been performed by a repair person not authorized by EURO-PRO Operating LLC.

This warranty is extended to the original purchaser of the unit and excludes all other legal and/or conventional warranties. The responsibility of EURO-PRO Operating LLC warranty if any, is limited to the specific obligations expressly assumed by it under the terms of the limited warranty. In no event is EURO-PRO Operating LLC liable for incidental or consequential damages of any nature whatsoever. Some states/provinces do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.

*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date and to attach tag to item before packing with your name, complete address and phone number with a note giving purchase information, model number and what you believe is the problem with the item. We recommend you insure the package (as damage in shipping is not covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER SERVICE”. We are constantly striving to improve our products, therefore the specifications contained herein are subject to change without notice.

Product Registration

Please visit www.sharksonicduo.com or call 1-800-798-7398 to register your new Shark® product within ten (10) days of purchase. You will be asked to provide the store name, date of purchase and model number along with your name and address.

The registration will enable us to contact you in the unlikely event of a product safety notification. By registering you acknowledge to have read and understood the instructions for use, and warnings set forth in the accompanying instructions.

EURO-PRO Operating LLC
U.S.: Newton, MA 02459
Canada: Ville St. Laurent, Québec H4S 1A7
1-800-798-7398
www.sharksonicduo.com

COPYRIGHT © 2013 EURO-PRO OPERATING LLC
PRINTED IN CHINA
KD401T.E.130103.2
Illustrations may differ from actual product.

FAQs

Can I keep the pad on when not in use?

Yes, but when leaving the cleaning pad on the system, it should be stored upright on storage tray. If it’s not placed on the storage tray while damp or wet, it may damage the floor.

Can I leave the bottle with cleaning solution in the Sonic Duo?

Yes, you can. This will not present a problem.

How can I polish around edges or on detailing trim?

To polish around edges or trim, we recommend using the Scrub Duster with the Polish Detail Pad. Just attach the pad, extend the wand and polish all of your hard-to-reach areas with ease.

How do I clean my reusable cleaning pads?

All cleaning pads are machine washable with liquid detergent only. Low dry setting only. Polish pad must be rinsed immediately after use/before being placed in washing machine with other cleaning pads.

How do I know if/when solution is coming out of nozzle?

You will hear an indicating sound while holding the spray button down. If you want to be doubly certain, you can lay a sheet of white paper down in front of the machine when spraying.

How do I lock the handle into place?

The word “front” must be facing away from power cord on body, push the handle firmly into Sonic Duo body, listen for a single audible click, handle will then sit flush with body.

How do I remove the bottle from Sonic Duo housing?

Twist the bottle and pull straight up.

How do I remove the handle?

On the back of the Sonic Duo, underneath the bottom cord wrap, there is a small hole containing a release button. Insert proper size tool (paperclip or something similar in diameter but rigid), firmly press the button and lift the handle to remove.

How much does it weigh?

5 pounds without solution.

Is it safe for my family and pets?

Cleaning solutions are non-toxic and are as gentle as hand soap. Both cleaners and polish are biodegradable and solvent free.

What is “Air Glide Maneuverability”?

“You can steer with just two fingers”. It is when the dual scrubbing action combined with the cleaning pads gives a push/pull feeling, similar to an air hockey table, when used on hard floor and carpets.

What is the best way to apply polish?

Use 28oz per 425 sq. ft. Do not buff polish into floor, there should be an even layer spread across floor (almost like painting)

What is the cord length on the Sonic Duo?

Depending on the model # it varies from 20-30 feet.

What is the cure time on the polish?

While a minimum of one to two hours is required before any minimal contact, we recommend up to 48 hours for it to completely dry.

What is the proper cleaning agent to water ratio? (Hard Floor)

1:7 for general cleaning. Always remember to fill container with water first, then your solution. This will prevent foaming.

What pads should I use with different solutions?

All pads and solutions are color coded: Green for hard floor cleaner, orange for hard floor polish.

What type of flooring can it be used on?

Hardwood, tile, stone, marble, laminate, linoleum – Polish is not to be used on pre-treated hard floor surfaces or laminate flooring.

When should I replace my pads?

Pads are machine washable, however you should replace every 3 months or 20 washes.

Why is my bottle leaking solution when removing?

When removing the bottle there will be cleaning solution left in the housing. This is a design feature, not a flaw. Also always make sure the “duck bill” valve inside the cap is securely fastened.

Why is the polish tag in the middle of the pad?

This is a design feature. If the tag was positioned on the edge of pad this would result in a streaky finish.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>