LiftMaster 837LM myQ Smart LED Garage Light Instruction Manual

: June 15, 2024
: LiftMaster

Table of Contents

LiftMaster 837LM myQ Smart LED Garage Light
Product Information
Installation
Programming
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LiftMaster 837LM myQ Smart LED Garage Light

Product Information

Specifications

Model: 837LM
Power: Standard 120V outlet
Installation: Indoor ceiling or wall mount

Installation

The myQ Smart LED Garage Light is designed to be mounted within 6 feet of an electrical outlet. Follow these steps for installation:

Select an appropriate location on the ceiling or wall.
If mounting on drywall without a ceiling joist, use the provided drywall anchors.
Hold the device up to the surface and secure it using screws.

Programming

Open the myQ app and navigate to Device Management.
Select your GDO under Hubs to pair it with the Smart LED Garage Light.
Add the Smart LED Garage Light as a new device and follow the pairing steps.
Press the learn button on the light and confirm the successful pairing.

Maintenance

Ensure the following conditions for proper operation:

No harmful interference should be caused.
The equipment must accept any interference that may occur.

Cord Retainer

This product includes a cord retainer for secure cable management.

Warning

This product contains chemicals, including lead, known to the State of California to cause harm. Refer to www.P65Warnings.ca.gov for more information.

FAQ

Q: Can the Smart LED Garage Light be used outdoors?
- A : No, the light is intended for indoor use only on ceilings or walls.
Q: How do I erase all programming from the light?
- A: Press and hold the learn button until the green LED turns off (6-10 seconds) to erase all programming.

Installation

The myQ Smart LED Garage Light is designed to plug directly into a standard 120V outlet. Select an appropriate location on the ceiling or wall to mount the light within 6 feet (1.83 m) of an electrical outlet so that the cord and light are away from moving parts.

NOTE : If installing light on drywall and a ceiling joist cannot be located, use the drywall anchors provided. No pilot hole is required for drywall anchors.

With the smart light lens open, hold the device up to the surface of the desired mounting location within 6 ft. from the electrical outlet. Mark screw hole locations on the mounting surface with a pen or pencil ( Figure 1 ).
If mounting to a wooden joist, use a 1/8″ bit to drill pilot holes at marked locations. OR Screw in the provided drywall anchors at marked mounting locations.
Determine the length of power cord needed to reach the nearest outlet. Wind any excess cord around the cord retainer on the top side of the smart light base. Route the cord through the channel so that the light is flush when mounted.
Line up the smart light’s screw holes with the marked mounting locations, insert the provided screws into the mounting guide holes, and screw in the smart light.
Close the smart light lens.
Plug in the smart light to the outlet. NOTE: The LED light is very bright and will blink while programming. DO NOT stare at the light while on a ladder.

Programming

PROGRAM A DOOR OPENER/OPERATOR TO THE myQ SMART LED GARAGE LIGHT

Press the LEARN button on the smart light until the green LED turns ON ( Figure 2 ).
Do one of the following operations ( Figure 3) :

Press the LEARN button on the door opener/operator. OR
Press the LEARN button on the door control twice. OR
On an LCD Smart Control Panel®, go to Menu > Program > myQ Device. OR
Using the myQ App, go to Menu > Program > myQ Device.
1. Open my app
2. Press your myQ account (icon at upper left screen) to open account settings.
3. Press “Device Management” to display the provisioned GDOs.
4. Press your GDO (under “Hubs”) to pair to your Smart LED Garage Light.
5. Press “Add New” (under Devices/Sensors paired to this Hub”) to see list of devices list.
6. Press “Smart LED Garage Light” to add this new device and follow the steps to pair the Smart LED Garage Light.
7. After pressing the learn button on the Smart LED Garage Light, Press “Next” to finish. The Smart LED Garage Light will blink once to confirm that it was successfully paired. The device has been learned when the smart light blinks once.

Once paired, the Smart LED Garage Light is added to your myQ account as an accessory.

PROGRAM A SECURITY + 2.0* REMOTE CONTROL TO THE myQ SMART LED GARAGE LIGHT

Press the LEARN button on the smart light until the green LED turns ON ( Figure 2 ).
Press the button on the remote control that you wish to operate the smart light.
The device has been learned when the smart light blinks once.

To program the smart light with another accessory, refer to the manual for your accessory.

TO ERASE ALL PROGRAMMING FROM THE myQ SMART LED GARAGE LIGHT

Press and hold the LEARN button on the smart light until the green LED turns off (6-10 seconds).

All programming is now erased.

Maintenance

Unplug the smart light before cleaning.
Use a lightly dampened cloth for cleaning.
DO NOT use liquid cleaners on the light lens.

Operation of this equipment is subject to the following two conditions: (1) This equipment or device may not cause harmful interference, and (2) This equipment or device must accept any interference, including that which may cause undesired operation.

WARNING: This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

NOTICE: This device complies with Part 15 of the FCC rules and Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device must be installed to ensure a minimum 20 cm (8 in.) distance is maintained between users/ bystanders and the device.

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules and Industry Canada ICES standard. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

LiftMaster

300 Windsor Drive Oak Brook, IL 60523
LiftMaster.com