LiftMaster 877MAX Garage Door Opener Keypad Instruction Manual

LiftMaster 877MAX Garage Door Opener Keypad

Product Information

Specifications:

• Product: Wireless Keyless Entry
• Buzzer Confirmation: Audible keyboard buzzer sounds
• Buzzer Default Setting: On

Product Usage Instructions

Turning On/Off the Keyboard Buzzer:

Each key press on the keyboard is accompanied by a beep confirmation. To set the keyboard to silent mode:

1. Turn On: Long press the 2 and 9 buttons simultaneously until you hear the voice of the keyboard buzzer.
2. Turn Off: Close the device, then long press the 2 and 9 buttons simultaneously until you hear the voice of the keyboard buzzer.

Note: The buzzer is turned on by default when the system leaves the factory.

FAQ:

Q: How do I know if the keyboard buzzer is turned on or off?

A: The keyboard buzzer is on by default. You can toggle it on or off using the specified button combinations as mentioned in the user manual.

Compatible with 315 MHz or 390 MHz garage door openers manufactured after January 1, 1993. Make sure the garage door opener has a working light bulb because it is a programming indicator. For use with commercial door operators or other products that are 315 MHz or 390 MHz and have a Learn button. Refer to your product manual for the location of the Learn button. Install the battery and program the Keyless Entry prior to installation.

PREPARE

PROGRAM INITIAL PIN

Press and hold the* and# buttons until the lights on the keypad stop blinking

Press and release the Enter button the number of times that corresponds with the garage door opener type:

To exit programming mode, press the 0 button.

Enter the 4-digit personal identification number (PIN) programmed in step 2 then press and release the Enter button until the garage door opener lights flash or two clicks are heard

CHANGE AN EXISTING PIN

PROGRAM A TEMPORARY PIN

A temporary 4-digit PIN can be programmed to allow access to visitors. Each programmed PIN can program one temporary PIN. The temporary PIN can be set for a number of door openings. The temporary PIN cannot be the same as any previously programmed PIN.

To test, press the temporary PIN, then press the ENTER button. The garage door opener will activate. If the temporary PIN was set for a number of openings, the test will use up one opening.

INSTALLATION

1. Select a location to mount the Keyless Entry at a minimum height of 5 feet (1.5 m) out of the reach of children.
2. Remove battery cover and battery.
3. Mark the top mounting hole and drill 1/8 inch (3.2 mm) pilot hole.
4. Install the top screw, allowing 1/8 inch (3.2 mm) to protrude above the surface. Position the Keyless Entry over the top screw.
5. Mark the bottom hole and drill 1/8 inch (3.2 mm) pilot hole. Install the bottom screw. Do not overtighten to avoid cracking the plastic housing.
6. Reinstall battery and replace cover.

OPERATION

The garage door opener activates when the PIN and ENTER button are pressed. The keypad will blink for 15 seconds, during that time the ENTER button can be used to stop, start or reverse the door. If the wrong number is accidentally pressed, press the correct PIN then the ENTER button. The Keyless Entry will transmit only the last four digits that were pressed before the ENTER button.

ONE BUTTON CLOSE:

To activate the one-button close feature:

1. Press and hold the 1 and 9 buttons for 10 seconds.
2. The keypad will blink twice when the one-button close feature is activated.

To deactivate the one-button close feature:

1. Press and hold the 1 and 9 buttons for 10 seconds.
2. The keypad will blink four times when one button close the feature is deactivated.

TURN ON/OFF THE KEYBOARD BUZZER:

Each key pressed on the keyboard is accompanied by a beep confirmation. However, you can set the keyboard to silent mode as follows:

• a. Turn on, long press 2 and 9 buttons, till you hear the voice of the keyboard buzzer.
• b. Close, long press 2 and 9 buttons, till you hear the voice of the keyboard buzzer.

Note: The buzzer is turned on by default when the system leaves the factory.

PASSWORD ANTI-TAILGATING

To prevent people entering with you from seeing the password you entered, you can enter the interference code when you enter the password. Enter the interference code. During this process, you can press any number (0 – 9 *) (except the # key) in the keyboard at will. After multiple interference codes are pressed, press the correct 4-digit password and end with the # button. The keyboard will automatically ignore all the invalid interference codes you entered after the “#” is entered, and transmit the code corresponding to the correct password.

FACTORY RESET:

If you get something wrong when program or enter PIN Code and can not proceed with any operation, you could reset the keypad PIN code for long press 0 and Enter buttons for 15 seconds till you hear a long sound to comfirm it.

BATTERY

WARNING

To prevent possible SERIOUS INJURY or DEATH:

• NEVER allow small children near batteries.
• If the battery is swallowed, immediately notify the doctor.

Replace the battery when the keypad becomes dim or does not light after a button is pressed. Dispose of old battery properly.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>