Alphalite LVT-4L-8A Linear LED Vapor Tight Instruction Manual

June 3, 2024
Alphalite

Alphalite LVT-4L-8A Linear LED Vapor Tight Instruction Manual
Alphalite LVT-4L-8A Linear LED Vapor Tight

WARNING
RISK OF FIRE OR ELECTRIC SHOCK
The LED Vapor Tight must be installed by a qualified electrician in accordance with applicable federal, state, and local laws and codes. Installation requires knowledge of luminaire electrical systems and installer should be familiar with the operation of this product. If not qualified, do not attempt installation; contact a qualified electrician. Manufacturer assumes no responsibility for the improper installation of this luminaire.

Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.

WARNING
To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects. When installing this kit, drilling may damage luminaire wiring and electrical parts. Check for wiring and components in enclosure before drilling.

Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.

WARNING
RISK OF PERSONAL INJURY
Wear gloves or proper handling protection to prevent cuts or abrasions when handling and maintaining this product. This equipment may have sharp edges.

WARNING
RISK OF PERSONAL INJURY, FIRE OR ELECTRIC SHOCK
Turn OFF power before installation.

Contact manufacturer with any questions or concerns regarding installation of this luminaire.

NOTICE: Green ground screw provided in proper location. Do not relocate.
NOTICE: Minimum 90o supple conductors
NOTICE: Specifications and dimensions subject to change without notice.
NOTICE: Suitable for wet location.

Installation Instructions

Surface Mounting
  1. Locate drill holes for mounting brackets. Use hardware  found in hardware kit. Mount bracket to surface.
    Installation instruction

  2. Secure mounting clips to housing recesses by firmly  pressing them into place until both sides of the clip are secured.
    Installation instruction

  3. Release latches by pulling top of latch away from housing.
    Installation instruction

  4. Without touching LED boards, detach LED tray and lens from fixture.
    Installation instruction

  5. Connect power to driver as shown in the figure. (the flexible cord supplied by others)
    Installation instruction

  6. Without touching LED boards, detach LED tray and lens from fixture.
    Installation instruction

  7. Connect power to driver as shown in the figure. (the flexible cord supplied by others)
    Installation instruction

  8. Follow general wiring Diagram on Figure for reference. Make sure the power supply is disconnected before installing.
    Installation instruction

  9. Reattach LED tray and lens to fixture by reversing step 5.
    Installation instruction

  10. Secure lens to housing with lens latches.
    Installation instruction

Chain Suspended Mounting Installation Instruction

Chain Suspended Mounting

  1. Attach V-bracket to each mounting clip by spreading the ends of the V-bracket apart and then inserting the legs   into the holes in the side of the mounting clips.
    Mounting instruction

  2. Secure mounting clips to housing recesses by firmly pressing them into place until both sides of the clip are secured. Hang fixture from customer supplied chain using V-brackets.
    Mounting instruction

  3. Hang fixture from customer supplied chain using V-brackets.
    Mounting instruction

  4. Release latches by pulling top of latch away from housing.
    Mounting instruction

  5. Follow general wiring Diagram on Figure for reference.
    Make sure the power supply is disconnected before installing.
    Mounting instruction

  6. Reattach LED tray and lens to fixture by reversing step 4
    Mounting instruction

  7. Secure lens to housing with lens latches.
    Mounting instruction

Wiring Diagram:
Wiring Diagram

Pendant mount
  1. Follow general wiring Diagram on Figure for reference.
    Pendant mount
    Make sure the power supply is disconnected before installing.

  2. Reattach LED tray to fixture by reversing step 5.
    Pendant mount

  3. Secure lens to housing with lens latches.
    Pendant mount

Support

10715 Springdale Ave, Ste 4, Santa Fe Springs, CA 90670 l
Tel: 1-888-287-9228
Fax: 1-888-258-9183
E-mail: support@alphalite.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals