BORMANN BPR6055 Working Lens Rechargeable 800LM Instruction Manual

BORMANN BPR6055 Working Lens Rechargeable 800LM

Safety instructions

Read the manual thoroughly and observe the information contained when using the device. Keep the manual close by for future reference. Refer to the information sheet enclosed for important information on the subjects of safety, disposal, guarantee and product care.

Intended Use

The product is designed for use both indoors and outdoors. The product is intended purely for private use and not for commercial purposes or other usage. The portable lamp is not suitable for lighting rooms within a household.

Observe the Safety Information
Read and observe all the safety information to protect yourself and the environment from any harm. Refer to the information sheet enclosed for the relevant information on safety.

WARNING! RISK OF FATAL INJURY THROUGH ELECTRIC SHOCK!
NEVER use the power adapter (12) if you suspect damage to the power adapter (12) or see damage to the power adapter (12).

• Do not put the device into operation if it is damaged.
• Never open or repair the power adapter (12) yourself.
• Never touch the bare contacts with metallic objects.
• Never plug in or unplug the power adapter (12) with wet hands.

Technical Data

Operating instructions

IMPORTANT! RISK OF PROPERTY DAMAGE THROUGH ENVIRONMENTAL INFLUENCES!
Unfavourable environmental influences could cause damage to the power adapter (12) or impair its function.

• Prevent exposing the device to environmental influences such as smoke, dust, vibration, chemicals, moisture, heat or direct sunlight.
• The power adapter (12) is not waterproof so keep it dry.

General View

1. Magnet (in base)
2. Base (pivoting)
3.  Hooks
4.  Magnet (at rear)
5. Press switch
6. Connection ports
7. Status indicator
8.  Housing
9. Spotlight
10. Working light
11. USB cable (with coaxial connector)
12. Power adapter*

Charging the Portable Lamp
The portable lamp is equipped with a permanently built-in Li-ion battery. The battery must be fully charged before being used for the first time. The four blue LEDs of the status indicator (7) indicate the charge status of the Li-ion battery.

1. Open the protective cover covering the connection ports (6).
   Underneath is one port for a coaxial plug and one USB-A port.

2. Connect the USB cable (11) to the port for a coaxial plug.

3.  Connect the USB cable (11) to the power adapter (12) supplied via the USB-A port.

4. Plug the power adapter (12) into a power socket.

5. During the charging process, one of the four blue LEDs of the status indicator (7) flashes.

6. When the charging process has finished, disconnect the USB cable (11) from the coaxial port. When the Li-ion battery is fully charged, all four blue LEDs in the status indicator (7) light up continually.

7. Close the protective cover covering the connection ports (6).
   Charge the portable lamp following each period of use or every three months.
   The portable lamp only fulfils the requirements of the type of protection specified when the protective cover covering the connection ports (6) is closed.

Operating the Portable Lamp
The portable lamp can operate in the following three operating modes which are selected by pressing the press switch (5). The switching cycle of the portable lamp operating modes is as follows:
Operating mode 1 → Operating mode 2 → Operating mode 3 → Off

• Operating mode 1 Working light energy-save mode (50% mode 1 brightness)
• Operating mode 2 Working light (100% brightness)
• Operating mode 3 Spotlight

Press the press switch (5) as often as necessary until the required mode is activated.

Dimming Function
The portable lamp is provided with a dimming function. You can adjust the brightness in any operating mode.

1. Press the press switch (5) to switch the portable lamp on and select the operating mode required.

2. Press and hold the press switch (5) to adjust the brightness.
   After a brief flash sequence, the brightness is reduced continuously. On reaching the minimum brightness, the portable lamp flashes briefly again and the brightness is continuously increased.

3.  Release the press switch (5) on reaching the required brightness.

Powerbank Function
The portable lamp is provided with a powerbank function to charge mobile devices via USB.

1. Open the protective cover covering the connection ports (6).
   Underneath is one port for a coaxial plug and one USB-A port.

2. Connect the device to be charged to the USB-A port using a USB cable. During the charging process, the four blue LEDs of the status indicator (7) light up.

3. Disconnect the USB cable from the micro USB-A connector when the charging process has finished.

4. Close the protective cover covering the connection ports (6).
   The portable lamp only fulfils the requirements of the type of protection specified when the protective cover covering the connection ports (6) is closed.

Magnet Function
You can use the magnet (1) in the base or magnets (4) on the rear to fix the portable lamp to steel surfaced parts. If you use the magnet (1) in the base, you can align the portable lamp by pivoting it on the base (2).

Using the Hooks
The portable lamp is equipped with two hooks (3) on the rear. The hooks (3) can be hinged out and turned in any direction.

• The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes significantly affect the performance and safety of the products. The parts described / illustrated in the pages of the manual that you hold in your hands may also concern other models of the manufacturer’s product line with similar features and may not be included in the product you just acquired.
• Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes.
• To ensure the safety and reliability of the product and the warranty validity, all repair, inspection, repair or replacement work, including maintenance and special adjustments, must only be carried out by technicians of the authorized service department of the manufacturer.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>