MEE audio H6D Bluetooth Wireless Headset With Dock And Boom Microphone User Manual

H6D BLUETOOTH
WIRELESS HEADSET
WITH DOCK AND BOOM MICROPHONE
POWERED BY

Package Contents

Package Overview

Charging

Low battery is indicated by a flashing red status indicator light and “battery low” voice notification every five minutes.
The charging time is approximately 2 hours. The red status indicator light on the headset will turn blue once fully charged.

Option 1: Using Charging Dock
Connect the dock to any powered USB port using the included micro-USB cable. The red power indicator light on the charging dock will light up.
Place headset on charging dock.

Option 2: Using USB Cable
Directly connect the H6D headset to any powered USB port using the included micro-USB cable.

Pairing

Press and hold the Multifunction button for about 8 seconds until the status indicator light flashes red and blue.
Note : The headset will enter pairing mode automatically on first use or after being reset.

Pairing (Continued)

Open the Bluetooth menu on the device you wish to pair (usually located in Settings->Bluetooth). If needed, select “search for devices”, “pair new device”, or “refresh.”

Select “MEE audio H6” and allow pairing to complete. Use “0000” if a pin is required.
Note : It is only necessary to pair your headset once with each device.

Reconnecting to Paired Devices

The H6D stores previously paired devices and reconnect automatically with the last paired Bluetooth device when powered on.
If the headset does not connect automatically, open the Bluetooth menu on your device and select “MEE audio H6” from the Bluetooth device list.

Wearing

Basic Functionality & Controls

*Not all devices support this functionality. For more information, refer to the user manual for your device.
**To start playing music, open a music app on your device and start playback.

Multipoint Functionality

Multipoint allows two Bluetooth devices to be connected to the headset simultaneously.
To use two Bluetooth devices with the H6D, first pair each one by following the pairing procedure described in the Pairing section, then power the headset off.
When powered on again, the headset will be able to connect to both devices. If one of the devices does not connect automatically, select “MEE audio H6” from the Bluetooth menu of the device.
To switch between the two connected devices, pause audio playback on the active device and start audio playback on the other connected device. It may take up to 30 seconds for the audio to switch.
Incoming calls will always take precedence over media. The H6D will automatically activate the connected device that has an incoming call.

Clear Memory (Delete Paired Devices)

To delete all previous Bluetooth pairings from memory, first power the headset on, then press and hold the Volume Up and Volume Down buttons at the same time for 5 seconds until the status indicator light flashes pink.
A new pairing will need to be created before the H6D can be used again by following the pairing procedure described in the Pairing section.

Support

For Additional Support
Visit our Bluetooth Support Guide at MEEaudio.com/Bluetooth for additional Bluetooth setup information
Still Have Questions?
Email Support: support@meeaudio.com
Safety and Care

• Clean with a soft cloth, damp with diluted soap water solution if necessary. Do not use chemical cleaners.
• Battery performance will be severely decreased when stored in extreme temperatures: below -10°C/14°F or above 45°C/113°F including direct sunlight.
• The lifetime of the battery will be significantly reduced if your headset is not charged for a long time. It is recommended to charge your headset at least once a month.

Warranty
MEE audio products purchased from authorized resellers are covered by a 1-year manufacturer warranty. For more information, visit MEEaudio.com/support

Warnings
Using headphones at high volumes for extended periods of time will result in permanent hearing damage. It is advised you keep volume levels moderate to low at all times for your safety. Turn the volume all the way down after connecting your headset, then gradually increase the volume until you reach a comfortable listening level.
Keep the device and packaging out of reach of children.
This device is designed and manufactured to operate within its defined design limits. Misuse may result in electric shock or fire. Read and follow these instructions carefully.

• To prevent fire or shock hazards, do not expose this unit to rain or moisture. If the device comes in contact with liquids, quickly wipe it away. If submerged in water, do not turn the device on until completely dried. Note: liquid submersion voids the warranty.
• The danger of explosion or fire if batteries are damaged. Keep away from direct sunlight, naked flames, flammable gasses, or heat sources such as radiators or stoves
• There are no user-replaceable/reparable parts in the headset. Disassembling it will void your warranty.
• Only use attachments/accessories specified by the manufacturer

Changes or modifications to this unit not expressly approved by MEE audio could void the
user’s authority to operate the equipment.

Compliance Information

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Rules

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Relocate the receiving antenna.
• Increase the separation between equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Disposal and Recycling

Dispose of this product in accordance with all local laws and regulations. Because this product contains electronic components and a battery, it must be disposed of separately from household waste. Contact local authorities to learn about disposal and recycling options.

MEE audio and its logo are registered trademarks of S2E, Inc. All rights reserved.
The Bluetooth ® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by MEE audio is under license. Other trademarks and trade names are those of their respective owners.
Siri ® is a registered trademark of Apple Inc.
All other trademarks are the property of their respective owners.

WARNING : Cancer and Reproductive Harm – www.P65Warnings.ca.gov
For more information about this warning visit MEEaudio.com/prop65

MEE audio H6D Bluetooth Wireless Headset With Dock And Boom Microphone User Manual – Download [optimized]
MEE audio H6D Bluetooth Wireless Headset With Dock And Boom Microphone User Manual – Download

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>