MEE audio B08RHYC7TK X20 Truly Wireless Active Noise Cancelling in Ear Headphone User Manual
- June 7, 2024
- mee audio
Table of Contents
X20
TRULY WIRELESS
ACTIVE NOISE CANCELLING
I NN–EEAARR HHEEAADDPPHHOONNEES
X20 SETUP GUIDE
Scan QR code or
visit:MEEaudio.com/X20Support
https://www.meeaudio.com/X20Support
POWERED BY
**GETTING STARTED
**
Package Contents
X20 Truly Wireless Earphones| 
Charging Case
---|---
Eartips (3 Pairs)| USB-C Charging Cable
STEP 1: CHARGING
Connect the charging case to a USB port or wall adapter using the included
USB cable.
Charging Case Indicator Lights
| Charging: Blinking Red | Charged: Solid White |
|---|
Place both earpieces in the case and close the lid or press the button on the
case to charge.
Earpiece Indicator Lights
| Charging: Solid White | Charged: Lights off |
|---|
STEP 2: PAIRING
Remove both earpieces from the case.
The right earpiece will automatically enter Bluetooth pairing
mode.
Earpiece Indicator Lights
Pairing mode is indicated by flashing alternating blue and white lights
Open the Bluetooth menu on your device and select “MEE audio X20”.
Earpiece Indicator Lights
Once pairing is complete, a blue light will blink intermittently
STEP 3: FITTING
Select the ear tips with the best sound and comfort for your ears.
Identify the left and right earpieces.
Put each earpiece in the corresponding ear.
Adjust each earpiece until it fits flush in your ear and the ear
tip seals the ear canal.
If your music sounds tinny or lacks bass, try different ear tips.
STEP 4: ACTIVE NOISE-CANCELING (ANC)
Press and hold the touch panel on either earpiece for 2 seconds to enable or
disable the Active Noise Canceling (ANC) function. A voice prompt will provide
the ANC status.
HOLD touch panel on either earpiece for 2 secs
STEP 5: POWERING OFF
When done listening, place both earpieces back in the case and close the
case lid.
Note: If earpieces are sweaty or damp, allow
them to fully dry before storing them in the case.
SUBSEQUENT USE
When removed from the charging case, the X20 reconnects automatically to the
last paired Bluetooth device that is in range.
To reconnect manually, open the Bluetooth menu on your device and select “MEE
audio X20” from the Bluetooth device list.
You can also use either earpiece as a single-ear headset by leaving the other
earpiece in the case.
FUNCTIONALITY & CONTROLS
Power On
|
Power Off
---|---
Play / Pause
TAP touch panel on either
earpiece
|
Turn ANC On / Off
HOLD touch panel on either
earpiece for 2 secs
Siri® / Google AssistantTM / Voice Control
TAP touch panel on either earpiece 2x
| 
Answer / End Call
AP touch panel on either earpiece
|
Reject Call
The TAP touch panel on either earpiece is 2x
PAIRING NEW DEVICES
When removed from the charging case, the X20 will automatically enter
Bluetooth pairing mode if a previously paired device is not found. Select “MEE
audio X20” in the Bluetooth menu of the new device you wish to pair to
complete the pairing process.
To manually enter pairing mode:
Remove the right earpiece from the case, press and hold the touch panel for 10
seconds to power it off, release the touch panel, then press and hold it again
for 5 seconds again until the blue and white lights flash indicating pairing
mode.
| Select “MEE audio X20” in the Bluetooth menu of the new
device you wish to pair to complete the pairing process.
---|---
TROUBLESHOOTING
A factory reset can be used to restore all features to their factory settings and delete all previous Bluetooth pairings from memory.
-
Place both earpieces in the case and close the lid
-
Open the lid, then press and hold the reset button on the case for approximately 10 seconds, until you see a solid white light on both earpieces
-
Release the button and allow the reset process to complete
-
Once you see alternating blue and white lights on the right earpiece indicating that the earphones are in pairing mode, follow the instructions in the “PAIRING” section to create a new pairing with your device
WARRANTY
MEE audio products purchased from authorized resellers are covered by a 1-year manufacturer warranty. For more information, contact your local MEE audio dealer or visit MEEaudio.com/Support
WARNINGS
Using headphones at high volumes for extended periods of time will result in
permanent hearing damage. It is advised you keep volume levels moderate to low
at all times for your safety. Turn the volume all the way down after
connecting your earphones, then gradually increase the volume until you reach
a comfortable listening level. Do not use headphones while driving a car,
cycling, operating machinery, or performing other activities that require
hearing surrounding sounds.
Keep the device and packaging out of reach of children.
This device is designed and manufactured to operate within its defined design
limits. Misuse may result in electric shock or fire. Read and follow these
instructions carefully.
- If submerged in water, do not turn the device on until completely dried. Note: liquid submersion voids the warranty.
- The danger of explosion or fire if batteries are damaged. Keep away from direct sunlight, naked flames, flammable gasses, or heat sources such as radiators or stoves
- Battery performance will be severely decreased when stored in extreme temperatures: below -10°C/14°F or above 45°C/113°F including direct sunlight
- Do not use around flammable gasses as fire or explosion may occur.
- There are no user-replaceable/reparable parts in the device. Disassembling it will void your warranty.
Only use attachments/accessories specified by the manufacturer
Changes or modifications to this unit not expressly approved by MEE audio could void the user’s authority to operate the equipment.
COMPLIANCE INFORMATION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC RULES
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Relocate the receiving antenna.
- Increase the separation between equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ·
- Consult the dealer or an experienced radio/TV technician for help.
DISPOSAL AND RECYCLING
Dispose of this product in accordance with all local laws and regulations. Because this product contains electronic components and a battery, it must be disposed of separately from household waste. Contact local authorities to learn about disposal and recycling options.
FOR ADDITIONAL SUPPORT
VIEW OUR VIDEO SETUP GUIDE
https://www.meeaudio.com/X20Support
Scan QR code or enter the URL below into your web browser:
MEEaudio.com/X20Support
QUESTIONS?
WE’RE HERE TO HELP!
Phone Support: 626-965-1008
Monday ~ Friday 9:00 am to 5:00 pm PST
Email Support: support@MEEaudio.com
All emails are responded to within 2 business days