Aladdin WHIP-LITE Flexible 120W Bi Color LED Light User Manual
- June 3, 2024
- ALADDiN
Table of Contents
Aladdin WHIP-LITE Flexible 120W Bi Color LED Light
START-UP GUIDE
1 | Switch between RGB and Bi-Color control |
---|---|
2 | Dimming control |
3 | Color temperature control |
4 | Velcro |
5 | Input box |
6 | Metal ring for mounting (can be attached to magnets) |
Unpack your panel and accessories from the box. The panel features a builtin
dimmer unit which can be controlled on the back of the panel. Plug in your AC
adapter or D-Tap cable to the input box of the panel. If the cable is too
short, just use the included extension cable in between. When you connect the
AC adapter to the power outlet you’re ready to go.
If you have also purchased the optional DMX Attachment (ALL-DMXAT) or the
Wired Dimmer (ALL-WDIM) you can put them between the panel (or extension
cable) and the AC adapter (or D-Tap cable).
Just note that you need batteries which can handle the power draw of 140
watts from the panel. There’s a simple calculation for that:
If your battery is rated at 14.8V and 100Wh/6.8Ah with a working current over
8A you can run your WHIP-LITE for a little less than one hour.
For any further questions about using our products please refer to our
customer service or watch the instructional videos on www.aladdin-
lights.com or YouTube.
DOWNLOAD THE APP
Using your WHIP-LITE panel with the new app for smartphones is a convenient way of controlling your light. It is available as free download on Android and iOS. You can store your own color filters in the app by dialling the desired Bi-Color values, have more control over the hues and saturation of lighting effects and much more. Give it a try and you will be amazed about the convenience in your workflow. Find the QR-codes for direct download below.
iOS
Android
IMPORTANT CAUTIONS AND WARNINGS
- Do not use near flammables and heaters.
- Do not expose the unit to direct sunlight for a long period (applies also for storing in a car).
- Do not use the dimmer wire or extension wire to hang or mount the panel.
- Do not bend or fold the panel more than 90 degrees.
- Do not tape directly on the LEDs of the panel – they can burn out.
- Do not damage the product with improper force or cause any impact with heavy objects.
- Do not cut the panel with sharp objects.
- Keep out of reach of children.
- The panel will heat up when running a long period of time on 100% power, make sure to have it in your eyesight at all times. Use the X-BEND holder or frame to assure enough air flow for heat reduction.
- Use the product only within temperature range of -10°C – +40°C.
- Make sure the panel has cooled down before storing it in the pouch or any other case.
- When you have technical problems while using the product, stop using it immediately and contact your dealer / reseller.
WARRANTY
We provide a one year warranty period after the purchase. This warranty covers
repairs or a replacement for faulty products within this period. After this
warranty has been expired, you can still get repairs for your product which
will be charged extra.
Aladdin Lights reserves the right to refuse warranty service on products under
disputable conditions.
WARRANTY EXCLUSIONS
In case of any of the below listed causes, the warranty does not apply, even
if it is within the free warranty period.
- Product failure due to consumer negligence.
- Product failure due to usage of not compatible power sources.
- Product failure due to disassembly by not official resellers/distributors.
SELECTED OPTIONAL ACCESSORIES
ALL-WDIM
The ALL-IN series controller allows you more control over the RGB and Bi-Color
values as well as effect values and DMX.
EXCA5M
Extend your light with the optional 5 meters of cable.
ALL-DTAB
Power your CAPE-LITE with external D-Tap power sources.
TECHNICAL SPECIFICATIONS
Light source | 120W Bi-Color |
---|---|
CRI | Ra 97 |
TLCI | 98 |
Color temperature | 2900K – 6100K |
Beam angle | 140° |
Dimmer | Dimming: (1%–100%) |
Cooling | Passive cooling |
Dimmer input | 12V to 24VDC |
Power unit input | Automatic voltage 100V to 240VAC |
Power consumption | 140W |
Dimensions | 3’340mm (W) x 170mm (H) x 18mm (D) (w/ built-in dimmer) |
Weight | 895g |
Connection | Bluetooth / Connector plug |
Temperature range | -10°C – +40°C |
DMX512 support | with optional DMX attachment / Controller |
DMX512 | 2 Channels – White Bi-Color |
IP-Rating | 32 |
Aladdin Lights
info@aladdin-lights.com