MINELAB ML85 Wireless Headphones Instruction Manual

: June 12, 2024
: MINELAB

**MINELAB ML85 Wireless Headphones Instruction Manual

**

The wireless headphones with its stylish design and ergonomic construction, powered with stereo sound drivers and the latest nRF5340 chip-set provides a high quality low-latency wireless audio experience.

Package Contents

Headphones
3.5mm Detachable Auxiliary cable
USB-C Charging Cable
Hard Shell Case
Detachable Mesh Bag
Instruction Manual

Product Specification

Chipset: Nordic nRF5340
Operating Range: up to 10m
Charging Time: 3 hours
Operating Time: 35-40 hours
Dimensions: 21.0 (L) x 16.0 (W) x 8 (H) cm (unfolded) 21.0 (L) x 16.0 (W) x 5 (H) cm (folded)
Weight: 221g
Operating frequency: 2.4-2.485GHz
Audio output power: 15mW x 2
Power of supply: 0.1W

Buttons and Indications

LED
Volume +
Multi-Function Button (MFB) (Power ON / OFF, Pairing and Factory Reset)
Volume –
3.5mm audio jack
USB-C charging port

Getting Started

To use your ML85 stereo wireless headphones, follow the steps below:

Ensure the wireless headphones are fully charged.
Pair the charged wireless headphones with a Minelab wireless enabled device

Charging the Headphones

Connect the USB-C charging cable to USB-C socket (6) of the headphones. The LED will remain solid red during charging.

Turning on the Headphones

Press and hold the MFB (3) until the LED (1) flashes solid blue for 1 second and then flashes red and blue. The headphones enter pairing mode automatically when no device is paired.

Turning off the Headphones

Press and hold the MFB (3) for 2 seconds until the headphones turn off.

Pairing the Headphones

Place the headphones and the detector no more than one metre apart.
Ensure the headphones are turned off.
Press and hold the MFB (3) until the LED (1) flashes red and blue.
Press and hold the wireless button on the detector for 2 seconds.
All of the wireless symbols will flash.
When the pairing is complete, the LED (1) will flash blue once every 3 seconds and will be connected to the detector.

Note: If the pairing cannot be completed the headphones will continue to attempt to pair until a connection is made.

Connect with the Last Paired Device

The headphones will connect with the last paired device. If the pairing is successful the LED (1) will flash blue every 3 seconds. If the pairing cannot be completed, the headphones will continue to attempt to pair until a connection is made.

Changing the volume

Press the Volume – button (4) once to decrease the volume.
Press the Volume + button (2) once to increase or the volume.

Reset to factory defaults (including unpairing)

Make sure the headphones are turned off. Press the MFB (3) for approximately 10 seconds until the LED (1) flashes red and blue twice then release the button. The headphones will now be in pairing mode with the LED indicator (1) flashing red and blue. All previously paired devices will be unpaired.

Using supplied 3.5mm headphone cable

A 3.5mm audio cable is included for use if the headphones battery is flat. You may also use the audio cable with devices that do not have wireless audio capability.

Troubleshooting

If you are unable to connect your headphones to your device, try the following:

Ensure your headphones are turned on and properly charged.
Ensure the headphones are paired with your device.
Ensure your devices wireless audio feature is activated. Refer to your devices user guide for specific instructions.
Ensure the headphones are within a 10 metre range of your device and there are no obstructions, such as walls or other electronic devices in between.
If the above steps do not solve your problem, recharge the headphones and turn the device off and on again.

Safety Information

Never allow children to play with the headphones, small parts are a choking hazard.
Observe all signs that require an electrical device or RF radio product to be switched off in designated areas. These could include hospitals, blasting areas, and potentially explosive environments.
Turn off your headphones prior to boarding an aircraft.
Never mount or store your headphones over any air bag deployment area as serious injury may result if the air bag deploys.
Do not open or mutilate the built-in battery.
Dispose of batteries according to local regulations. Do not dispose as household waste.
Only charge the headphones built-in battery in accordance with the instructions contained in the user guide.
Avoid charging the headphones in extreme temperature conditions.

Care and Maintenance Headphone

Turn the headphones off before placing in a pocket or bag.
Do not expose the headphones to liquid, moisture or humidity, as the headphones are not waterproof.
Do not use abrasive cleaning solvents to clean the headphones.
Do not expose the headphones to extreme temperature conditions. The storage temperature range is from -0 to +60 Celsius.
Do not dispose the headphones in a fire as this may result in an explosion.
Do not bring the headphones into contact with sharp objects as this will cause scratches and damage.
Do not attempt to disassemble the headphones, as they do not contain serviceable components.
If the headphones are not used for long periods, store in a dry place free from extreme temperature conditions and dust.

Software Upgradeable

The ML85 headphones can be updated via the USB-C connection.
Please refer to www.minelab.com/support for more details.

Wireless Compatibility

The wireless technology used in the ML85 headphones is only compatible with certain Minelab metal detectors. Please refer to www.minelab.com/support for more details.

Minelab reserves the right to introduce changes in design, equipment and technical features at any time without notice and Minelab™ is a trademark of Minelab Electronics Pty. Limited.