NameLessRC D400 VTX+DVR AIO User Manual
- June 8, 2024
- NameLessRC
Table of Contents
NameLessRC D400 VTX+DVR AIO
User Manual
Specification：
-Brand Name: NameLessRC
-Item Name: D400 VTX+DVR AIO
-Input Power: 5V
-Output Power: PIT/25mW/100mW/200mW/400mW Switchable
-Frequency: 5.8GHz 6 bands 48 channels, with Raceband: 5362-5945 MHZ
-Control Mode: BFOSD Control/ Button, IRC Tramp ready
-Video Output format: NTSC
-Record video size : 1280×720 @30FPS
-TF Card support: Max.32G
-Compress Format: AVI
-Microphone: Yes
-Antenna: IPEX
-Mounting hole: 26.5*26.5mm
-Weight: 3.5g without antenna
Features:
-VTX maximum power up to 400mW.
-Built-in microphone.
-Support to choose recording FC OSD info or not.
-Start/Stop recording via button or OSD. Automatic recording after power on.
-Automatically save a video every 5 minutes.
-Cable plug and welding pads are both available.
-Small & light size for whoop and toothpick style frames.
-The VTX will not be damaged even if the antenna is dropped.
Attention:
-VTX’s default setup is on lock mode(5733-5866MHZ unlock). Please follow your local laws and regulations if you need to unlock the frequency.
-Please format the TF card to FAT/FAT32.
Pins Assignment：
Note:
You can choose to use the included cables or welding pads according to your
needs.
Precautions for use：
-Please maintain a good cooling environment for better performance.
-Input voltage must be within the specified range 5V.
-Please choose antenna with good VSWR and DB if you replace, to get far transmission distance.
-Please use good TF card for better recording quality.
-Pay attention to static electricity protection during transportation and installation.
Control methods： VTX lock/unlock
(D400 VTXcable for Betaflight 4.1: https://drive.google.com/open?id =1LR2UCBB_0OrupfQlvufxuH7ozPHD-1YI)
-The VTX is set up via BFOSD Control (IRC Tramp) or button.
-The VTX’s default set up is lock on 25mw.
-To lock/unlock the VTX :
Option 1: Long press the VTX button for 25 seconds after power on. The 3 LEDs will flash one by one if the VTX is successful to unlock. Please re-power the VTX after this step.
Option 2: Please enter the PIT mode for three times within 30secs after powering up the VTX (PIT mode switch is set in BF mode page). The 3 LEDs will flash one by one if the VTX is successful to unlock. Please re-power the VTX after this step.
VTX LED functions：
-Orange LED shows channels status. Green for bands and Blue for power. -The Green LED flash after Orange and blue LED flash at the same time means the VTX enters PIT mode successfully.
-The three LEDs will flash one by one after the VTX is powered. After that, each LED will flash to show the channel, band & power’s status. Orange LED flash 1 time for Channel 1, 2 times for Channel 2. Green LED flash 1 time for Band 1, 2 times for Band 2, and so on. The three LEDs will flash one by one again after finish showing the status.
VTX Channel/Band/Power set up：
-Power the D400 and long press VTX button for 3 seconds. The Channel Orange LED will flash. 1 time for Channel 1, 2 times for Channel 2 and so on. Short press to switch the Channel.
-Long press VTX button for 3 seconds after step 1, the Band Green LED will flash.
1 time for Band 1, 2 times for Band 2 and so on. Short press to switch the
Band.-Long press VTX button for 3 seconds after step 2, the Power Blue LED
will flash.
1 time for 25mW, 2 times for 100mW and so on. Short press to switch the Power.
-Long press VTX button for 3 seconds after step 3 or re-power the D400, the set up will be saved.（Re-power during each step also can save the set up)
Frequency Table(Mhz):
Red area on frequency table is locked area! Please follow your local laws and regulations.
Channel
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
---|---|---|---|---|---|---|---|---
Band A
|
5865
|
5845
|
5825
|
5805
|
5785
|
5765
|
5745
|
5725
Band B
|
5733
|
5752
|
5771
|
5790
|
5809
|
5828
|
5847
|
5866
Band E
|
5705
|
5685
|
5665
|
5645
|
5885
|
5905
|
5925
|
5945
FS
|
5740
|
5760
|
5780
|
5800
|
5820
|
5840
|
5860
|
5880
Race Band
|
5658
|
5695
|
5732
|
5769
|
5806
|
5843
|
5880
|
5917
Low Race
|
5362
|
5399
|
5436
|
5473
|
5510
|
5547
|
5584
|
5621
DVR Recording:
– DVR White LED constantly bright means it is in standby, flashing means recording.
Option 1: Automatic recording after power on.
Option 2: Short press the DVR button to start/stop recording.
Option 3: Start/stop recording via OSD control (Video: https://youtu.be/v9MAinKmdsQ)
-Enter the OSD VTX set up page
-Switch the POWER to ON and confirm. The code will show 513 which means the DVR is starting to recording. Meanwhile, the DVR White LED will be flashing.
-Switch the POWER to OFF and confirm. The code will show 515 which means the DVR stop recording. Meanwhile, the DVR White LED will be constantly bright.
Note: We recommend setting the power you expect again after start/stop recording via OSD.
NameLessRC D400 VTX DVR AIO User Manual – Download
[optimized]
NameLessRC D400 VTX DVR AIO User Manual – Download
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>