Sunny Health and Fitness SF-RW5515 Magnetic Rowing Machine User Manual
- June 8, 2024
- Sunny Health and Fitness
Table of Contents
Sunny Health and Fitness SF-RW5515 Magnetic Rowing Machine User Manual
IMPORTANT SAFETY INFORMATION
We thank you for choosing our product. To ensure your safety and health, please use this equipment correctly. It is important to read this entire manual before assembling and using the equipment. Safe and effective use can only be achieved if the equipment is assembled, maintained, and used properly. It is your responsibility to ensure that all users of the equipment are informed of all warnings and precautions.
-
Before starting any exercise program, you should consult your physician to determine if you have any medical or physical conditions that could put your health and safety at risk or prevent you from using the equipment properly. Your physician’s advice is essential if you are taking medication that affects your heart rate, blood pressure, or cholesterol level.
-
Be aware of your body’s signals. Incorrect or excessive exercise can damage your health. Stop exercising if you experience any of the following symptoms: pain, tightness in your chest, irregular heartbeat, shortness of breath, lightheartedness, dizziness, or feelings of nausea. If you do experience any of these conditions, you should consult your physician before continuing with your exercise program.
-
Keep children and pets away from the equipment. The equipment is designed for adult use only.
-
Use the equipment on a solid, flat level surface with a protective cover for your floor or carpet. To ensure safety, the equipment should have at least 2 feet (60 CM) of free space all around it.
-
Ensure that all nuts and bolts are securely tightened before using the equipment. The safety of the equipment can only be maintained if it is regularly examined for damage and/or wear and tear.
-
Always use the equipment as indicated. If you find any defective components while assembling or checking the equipment, or if you hear any unusual noises coming from the equipment during exercise, discontinue use of the equipment immediately and do not use until the problem has been rectified.
-
Wear suitable clothing while using the equipment. Avoid wearing loose clothing that may become entangled in the equipment.
-
Do not place fingers or objects into the moving parts of the equipment.
-
The maximum weight capacity of this unit is 250 pounds (110KG).
-
The equipment is not suitable for therapeutic use.
-
To avoid bodily injury and/or damage to the product or property, proper lifting and moving are required.
-
Your product is intended for use in cool and dry conditions. You should avoid storage in extreme
cold, hot or damp areas as this may lead to corrosion and other related problems. -
This equipment is designed for indoor and home use only; it is not intended for commercial use
EXPLODED DIAGRAM
No . | Description | Spec . | Qty |
---|---|---|---|
1 | Front Stabilizer | 1 | |
2 | Washer | d8Φ161.5 | 6 |
3 | Screw | M85520*S6 | 2 |
4L/R | End Cap | 3 | |
5 | Nut | M8H7.5S13 | 4 |
6 | Screw | ST4.225Φ10.5 | 1 |
7 | Handlebar | 2 | |
8 | Foam Grip | Φ263215 | 2 |
9 | End Cap | Φ28*15 | 1 |
10 | Left Belt Cover | 11 | |
11 | Screw | ST4.219Φ8 | 7 |
12 | Screw | ST4.216Φ8 | 1 |
13 | Computer | 1 | |
14 | Tension Control Knob | 1 | |
15 | Washer | D5 | 1 |
16 | Screw | M5 | 4 |
17 | Nut | M101H8*S15 | 4 |
18 | Nut | M101H5*S17 | 1 |
19 | Cover for Mesh Belt Wheel | Φ149*14 | 1 |
20 | Outer PC Board | 1 | |
21 | Volute Spring | 1 | |
22 | Axle for Mesh Belt Wheel | 1 | |
23 | Bearing | 6000-ZZ | 4 |
24 | PC Board | 1 | |
25 | Bolt | M545Φ4.8 | 1 |
26 | Mesh Belt Wheel | Φ145 | 1 |
27 | Belt Whee | Φ104 | 1 |
28 | Bolt | M655S10 | 3 |
29 | Circlip | d10 | 3 |
30 | Bolt | M65515*S10 | 1 |
31 | Wave Washer | Φ13.5Φ10.20.4 | 1 |
32 | Spacer | Φ10Φ6.140 | 1 |
33 | Mesh Belt Pulley | Φ45*35 | 1 |
34 | Screw | M816S6 | 4 |
35 | Washer | d8Φ201.5 | 10 |
36 | Handlebar Seat | 1 | |
37 | Screw | M510Φ10 | 2 |
38 | Mesh Belt | t1.5222270 | 1 |
39 | Belt | 6PJ250 | 1 |
40 | Inertial Wheel | Φ176 | 1 |
41 | Adjusting Screw | M640Φ10*2.5 | 4 |
42 | Adjusting U Seat | 30101.5 | 4 |
43 | Nut | M6H6S10 | 8 |
44 | Main Frame | 1 | |
45 | Trunk Wire 1 | 1 | |
46 | Washer | d12Φ242 | 1 |
47 | Knob | M12 | 1 |
48 | Bolt | M12Φ12.5160*S19 | 4 |
49L/R | Pedal L/R | 2 | |
50 | Pedal Strap | 2 | |
51 | Magnet | Φ15*7 | 1 |
52 | Spring Washer | d8 | 8 |
53 | Wheel | Φ40*92 | 3 |
54 | Casing Pipe for Idler Wheel | Φ13Φ878 | 3 |
55 | Bearing | 608Z | 6 |
56 | Rubber Pad | 1 | |
57 | Right Belt Cover | 1 | |
58 | Bolt | Φ1095M6*25 | 1 |
59 | Screw | Φ8100105 | 1 |
60 | Pull Pin | Φ8100105 | 1 |
61 | Sensor Wire | 1 | |
62 | Sliding Rail | 1 | |
63 | Screw | M616Φ12 | 4 |
64 | Washer | d6Φ121 | 5 |
65 | Limit Mat | Φ33Φ813 | 4 |
66 | Limit Axle | Φ1280M6 | 2 |
67 | Grommet | Φ1615Φ5 | 1 |
68 | End Cap | J804018 | 1 |
69 | Rear Support | 1 | |
70 | End Cap | 2 | |
71 | Seat | DDPU986 | 1 |
72 | Screw | M820S6 | 4 |
73 | Bolt | M812515*S14 | 3 |
74 | U Shape Bracket | 2 | |
75 | Left Seat Supporting | 1 | |
76 | Right Seat Supporting | 1 | |
77 | Spacer | d8Φ154 | 6 |
78 | Spanner | S17-19 | 1 |
79 | Allen Wrench | S5 | 1 |
80 | Allen Wrench | S6 | 1 |
81 | Spanner | S13-14-15 | 1 |
PARTS LIST HARDWARE PACKAGE
ASSEMBLY INSTRUCTIONS
STEP 1:
Attach Front Stabilizer (No. 1) to Main Frame (No. 44) using 2 Screws (No. 3) and 2 Washers (No. 2). Tighten and secure with Allen Wrench (No. 80).
STEP 2:
Fix the 2 Bolts (No. 48) in position A into the bottom hole of Main Frame (No. 44) with Spanner (No.78).
Attach the 2 Bolts (No.48) into the upper hole of the Main Frame (No. 44) through the Pedals (No.49) and tighten with Spanner (No.78).
NOTE: The Pedals (No.49) should be attached by the Bolts (No.48) in position A.
STEP 3:
Insert the Seat (No. 71) onto S liding Rail (No. 62).
Insert the Limit Axle (No. 66) into the hole on the back of the Sliding Rail (No. 62).
Attach the Limit Mat (No. 65) onto the Limit Axle (No. 66) using 1 Screw (No. 63) and 1 Washer (No. 64) , then tighten with **Spanner (No. 81).
81**
STEP 4:
Attach Sliding Rail (No. 62) onto Rear Support (No. 69) using 4 Screws
(No. 72), 4 Spring Washers (No. 52), and 4 Washers (No. 2). Tighten and secure
with Allen Wrench (No. 80).
STEP 5:
Connect Trunk Wire 1 (No. 45) with Sensor Wire (No. 61).
Attach the Sliding Rail (No. 62) to Main Frame (No. 44) using 1 Bolt
(No. 58) and 1 Screw (No. 59). Tighten and secure with Allen Wrench
(No. 79) and Allen Wrench (No. 80). Next, attach the top of the
Sliding Rail (No. 62) to the Main F rame (No. 44) using 1 Knob (No.
47) and 1 Washer (No. 46) , then insert Pull Pin (No. 60).
STEP 6:
Take out 2 AAA batteries from the plastic bag with the manual. Press the buckle on the bottom of Computer (No. 13) upward, then remove Computer (No. 13) from Main Frame (No. 44).
Disconnect Trunk Wire 1 (No. 45) and the link wire of Computer (No. 13).
Install the 2 AAA batteries into the back of Computer (No. 13).
STEP 7:
Connect Trunk Wire 1 (No. 45) with the link wire of Computer (No. 13)
and press the buckle on the bottom of Computer (No. 13) , then put
Computer (No. 13) back onto the Main Frame (No. 44). Push the
Computer (No. 13) downwards to fit in position.
ADJUSTMENT S & USAGE GUIDE
CAUTION! Moving parts, such as the seat, can cut and crush. Keep hands clear of the sliding rail during use!
PEDAL STRAP ADJUSTMENT
The pedal strap is adjustable and can be personalized to fit the user’s foot
size.
MOVING THE ROWER
To move the rower, lift up the Rear Support (No. 69) until the transportation
wheels on the front stabilizer touch the ground. With the wheels on the
ground, you can transport the rower to the desired location with ease.
ADJUSTING THE BALANCE AND RESISTANCE
Adjust the End Caps (No. 70) on the Rear Support (No. 69) of the
rower if the rower is unbalanced during use.
Rotate the Tension Control Knob (No. 14) clockwise to increase the level of resistance. Rotate the Tension Control Knob (No. 14) counter-clockwise to decrease the level of resistance.
Tension levels are set at Level 1 being the lowest and Level 8 being the
highest.
REPLACE THE BATTERIES
Two AAA batteries are included in Computer (No. 13). To replace the
batteries, remove Computer (No. 13) from Main Frame (No. 44), and
disconnect the Trunk Wire 1 (No. 45 ) and the link wire of Computer (No.
13). Replace both batteries. Do not mix battery types and do not mix old and
new batteries.
After the replacement, connect T runk Wire 1 (No. 45) with the link wire
of Computer (No. 13) and put Computer (No. 13) back onto the Main Frame
(No. 44). Dispose of batteries according to your state and local rules.
STORAGE GUIDE
EXERCISE COMPUTER
FUNCTION KEYS:
MODE: To select your specification mode and/or turn on computer.
SET: To set a value of Time, Count, or Calories (when not in Scan mode).
RESET: Press to reset Time, Count, or Calories. Press and hold for about
3 seconds to reset all values, expect Total Count.
FUNCTIONS AND OPERATIONS:
AUTO ON/OFF: The power will turn off automatically once there is no
signal for 4 minutes. The computer will reactivate once the machine is put
into motion or when a computer button is pressed.
SCAN: Press MODE button until SCAN appears. The computer will rotate
through the four functions in the following order: TIME, COUNT, TOTAL COUNT,
and CALORIES. Each function will be held for 6 seconds.
TIME: Counts the total time elapsed during your current workout.
COUNT: Counts the number of rowing strokes from your current workout.
TOTAL COUNT: Counts the total amount of strokes from the first use.
CAL: Counts the total calories burned from current workout.
COUNTDOWN:
You can set the value of Time, Count or Calories to countdown.
- Press MODE to select a function. Make sure you are not in SCAN mode.
- Press SET to select a value you want. You can press RESET to clear the value.
- When the display stops flashing, start rowing and the machine will start to
countdown. BATTERY: This computer uses two AAA batteries. If the display appears incorrectly or becomes difficult to read, please install new batteries. Always change both batteries at the same time. Do not mix battery types and do not mix old and new batteries. Dispose of batteries according to your state and regional guidelines.
SPECIFICATIONS
FUNCTIONS
| SCAN| Every 6 seconds
---|---|---
TIME| 0:00~99:59 (Minute: Second)
COUNT| 0~9999 Count
CALORIES| 0.0~9999 Kcal
TOTAL COUNT| 0~9999 Count
BATTERY TYPE| (2) Two AAA or UM-4
OPERATING TEMPERATURE| 0°C ~ 40°C
STORAGE TEMPERATURE| -10°C ~ 60°C
IMPORTANT! Please retain owner’s manual for maintenance and adjustment
instructions. Your satisfaction is very important to us, PLEASE DO NOT
RETURN UNTIL YOU HAVE CONTACTED
US: support@sunnyhealthfitness.com or 1- 877 – 90SUNNY
(877-907-8669).
CONTACT WITH US
For Fitness Articles, Videos & Workouts
Sunnyhealthfitness.com/signup
@SUNNYHEALTHFITMNESS
@SUNNYHEALTHFITMNESS
@SUNNYHEALTHFITMNESS
Sunny Health and Fitness SF-RW5515 Magnetic Rowing Machine User Manual –
Download [optimized]
Sunny Health and Fitness SF-RW5515 Magnetic Rowing Machine User Manual –
Download
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>