Showtec Shark The Meg Hybrid LED Moving Head User Manual

June 12, 2024
Showtec

Showtec Shark The Meg Hybrid LED Moving Head

Showtec-Shark-The-Meg-Hybrid-LED-Moving-Head

Product Information

  • Product Name: Shark – The Meg – Hybrid One
  • Product Code: 45041
  • Firmware Version: 2.0

Product Usage Instructions

Before Using the Product:

  • Read and follow the instructions in this user manual before installing, operating or servicing this product.
  • Check the contents of the box after unpacking. If any parts are missing or damaged, contact your Highlite International dealer.
  • Contents of the shipment:
    • Showtec Shark – The Meg – Hybrid One
    • Schuko to Power Pro cable (1,5 m)
    • Safety cable
    • 2x Quick-lock bracket
    • User manual

Safety:

  • Follow all warnings and safety instructions provided in this user manual.

Troubleshooting:

  • Refer to the troubleshooting section in this user manual for assistance in resolving any issues with the product.

Disposal:

  • Follow the proper procedures for disposal of the product as described in this user manual.

Approval:

  • Refer to the approval section in this user manual for information on product compliance and certifications.

Note: Non-observance of the instructions in this user manual may result in serious injuries and damage of property. The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual.

USER MANUAL

ENGLISH

Shark – The Meg – Hybrid One

V1

Product code: 45041 Firmware version: 2.0

Highlite International B.V. ­ Vestastraat 2 ­ 6468 EX ­ Kerkrade ­ the Netherlands

Shark – The Meg – Hybrid One

Preface

Thank you for purchasing this Showtec product.
The purpose of this user manual is to provide instructions for the correct and safe use of this product.
Keep the user manual for future reference as it is an integral part of the product. The user manual shall be stored at an easily accessible location.
This user manual contains information concerning:
Safety instructions Intended and non-intended use of the device Installation and operation of the device Maintenance procedures Troubleshooting Transport, storage and disposal of the device
Non-observance of the instructions in this user manual may result in serious injuries and damage of property.

©2023 Showtec. All rights reserved.
No part of this document may be copied, published or otherwise reproduced without the prior written consent of Highlite International.
Design and product specifications are subject to change without prior notice.
For the latest version of this document and other language versions, please visit our website www.highlite.com or contact us at service@highlite.com.
Highlite International and its authorized service providers are not liable for any injury, damage, direct or indirect loss, consequential or economic loss or any other loss arising from the use of, or inability to use or reliance on the information contained in this document.

Product code: 45041

1

Shark – The Meg – Hybrid One
Table of contents
1. Introduction……………………………………………………………………………………………………………………………………….4 Before Using the Product ………………………………………………………………………………………………………………….4 Intended Use …………………………………………………………………………………………………………………………………….4 Product Lifespan……………………………………………………………………………………………………………………………….4 LEDs Lifespan …………………………………………………………………………………………………………………………………….4 Text Conventions ………………………………………………………………………………………………………………………………4 Symbols and Signal Words………………………………………………………………………………………………………………..5 Symbols on the Information Label ……………………………………………………………………………………………………5
2. Safety ………………………………………………………………………………………………………………………………………………..6 Warnings and Safety Instructions ……………………………………………………………………………………………………..6 Requirements for the User…………………………………………………………………………………………………………………8
3. Description of the Device …………………………………………………………………………………………………………………..9 Front View …………………………………………………………………………………………………………………………………………9 Back View ……………………………………………………………………………………………………………………………………….10 Bottom View ……………………………………………………………………………………………………………………………………10 Product Specifications ……………………………………………………………………………………………………………………11 Dimensions ………………………………………………………………………………………………………………………………………12
4. Installation ……………………………………………………………………………………………………………………………………….13 Safety Instructions for Installation ……………………………………………………………………………………………………13 Personal Protective Equipment ………………………………………………………………………………………………………13 Installation Site Requirements …………………………………………………………………………………………………………13 Rigging ……………………………………………………………………………………………………………………………………………14 Connecting to Power Supply………………………………………………………………………………………………………….15 Power Linking of Multiple Devices…………………………………………………………………………………………………..15
5. Setup ……………………………………………………………………………………………………………………………………………….16 Warnings and Precautions ……………………………………………………………………………………………………………..16 Stand-alone Setup ………………………………………………………………………………………………………………………….16 DMX Connection…………………………………………………………………………………………………………………………….16 DMX-512 Protocol ………………………………………………………………………………………………………………………16 DMX Cables ……………………………………………………………………………………………………………………………….17 Master/Slave Setup ……………………………………………………………………………………………………………………17 DMX Linking………………………………………………………………………………………………………………………………..18 DMX Addressing…………………………………………………………………………………………………………………………18
6. Operation ………………………………………………………………………………………………………………………………………..19 Safety Instructions for Operation …………………………………………………………………………………………………….19 Control Modes ………………………………………………………………………………………………………………………………..19 Control Panel ………………………………………………………………………………………………………………………………….20 Start-up ……………………………………………………………………………………………………………………………………………20 Menu Overview ………………………………………………………………………………………………………………………………21 Main Menu Options ………………………………………………………………………………………………………………………..26 DMX Functions……………………………………………………………………………………………………………………………26 DMX Address ………………………………………………………………………………………………………………………26 Channel Mode …………………………………………………………………………………………………………………..27 Auto Run …………………………………………………………………………………………………………………………….27 Music Run ……………………………………………………………………………………………………………………………28 Fixture Settings ……………………………………………………………………………………………………………………………29 Manual……………………………………………………………………………………………………………………………………….30 Advanced ………………………………………………………………………………………………………………………………….31 DMX Channels ………………………………………………………………………………………………………………………………..32 8 Channels, 16 Channels, 18 Channels ……………………………………………………………………………………..32 Rotating Gobo Wheel, Static Gobowheel and Color Wheel ………………………………………………………..35
7. Troubleshooting ……………………………………………………………………………………………………………………………….36

Product code: 45041

2

Shark – The Meg – Hybrid One
8. Maintenance …………………………………………………………………………………………………………………………………..37 Safety Instructions for Maintenance……………………………………………………………………………………………….37 Preventive Maintenance ………………………………………………………………………………………………………………..37 Basic Cleaning Instructions ………………………………………………………………………………………………………..37 Corrective Maintenance ………………………………………………………………………………………………………………..38 Replacing the Fuse…………………………………………………………………………………………………………………….38
9. Deinstallation, Transportation and Storage ……………………………………………………………………………………….39 Instructions for Deinstallation…………………………………………………………………………………………………………..39 Instructions for Transportation …………………………………………………………………………………………………………39 Storage ……………………………………………………………………………………………………………………………………………39
10. Disposal …………………………………………………………………………………………………………………………………………..39
11. Approval………………………………………………………………………………………………………………………………………….39

Product code: 45041

3

Shark – The Meg – Hybrid One
1. Introduction
Before Using the Product
Important Read and follow the instructions in this user manual before installing, operating or servicing this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual.
After unpacking, check the contents of the box. If any parts are missing or damaged, contact your Highlite International dealer.
Your shipment includes: Showtec Shark – The Meg – Hybrid One Schuko to Power Pro cable (1,5 m) Safety cable 2x Quick-lock bracket User manual

Fig. 01

Intended Use

This device is intended for professional use as a moving head. It is not suitable for households and for general lighting.

Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.

Product Lifespan

This device is not designed for permanent operation. Disconnect the device from the electrical power supply when the device is not in operation. This will reduce the wear and will improve the device’s lifespan.

LEDs Lifespan

The light output of the LEDs gradually decreases over time (lumen depreciation). High operating temperatures contribute to this process. You can extend the lifespan of the LEDs by providing adequate ventilation and operating the LEDs at the lowest possible brightness.

Text Conventions

Throughout the user manual the following text conventions are used:

Buttons:

All buttons are in bold lettering, for example “Press the UP/DOWN buttons”

Product code: 45041

4

Shark – The Meg – Hybrid One

References:
0­255: Notes:

References to chapters and parts of the device are in bold lettering, for example: “Refer to 2. Safety”, “turn the adjustment handle (05)” Defines a range of values Note: (in bold lettering) is followed by useful information or tips

Symbols and Signal Words

Safety notes and warnings are indicated throughout the user manual by safety signs. Always follow the instructions provided in this user manual.

DANGER

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.

Attention

Indicates important information for the correct operation and use of the product.

Important Read and observe the instructions in this document.

Electrical hazard

Provides important information about the disposal of this product.

Symbols on the Information Label
This product is provided with an information label. The information label is located on the mounting bracket of the device.
The information label contains the following symbols:

This device shall not be treated as household waste.

This device is designed for indoor use.
This device falls under IEC protection class I.
Minimum distance from lighted objects.
Minimum distance from other objects.
Replace any cracked protective shield. Caution: Risk of electric shock. Do not open. Caution: To reduce the risk of electrical shock, do not remove cover. No userserviceable parts inside. Refer servicing to qualified personnel.

Product code: 45041

5

Shark – The Meg – Hybrid One
2. Safety
Important Read and follow the instructions in this user manual before installing, operating or servicing this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual.
Warnings and Safety Instructions
DANGER Danger for children
For adult use only. The device must be installed beyond the reach of children.
Do not leave various parts of the packaging (plastic bags, polystyrene foam, nails, etc.) within children’s reach. Packaging material is a potential source of danger for children.
DANGER Electric shock caused by dangerous voltage inside
There are areas within the device where dangerous touch voltage may be present.
Do not open the device or remove any covers. Do not operate the device if the covers or the housing are open. Before operation, check if the
housing is firmly closed and all screws are tightly fastened. Disconnect the device from electrical power supply before service and maintenance, and when the
device is not in use.
DANGER Electric shock caused by short-circuit
This device falls under IEC protection class I.
Make sure that the device is electrically connected to ground (earth). Connect the device only to a socket-outlet with ground (earth) connection.
Do not cover the ground (earth) connection. Do not bypass the thermostatic switch or fuses. Do not let the power cable come into contact with other cables. Handle the power cable and all
connections with the mains with caution. Do not modify, bend, mechanically strain, put pressure on, pull or heat up the power cable. Make sure that the power cable is not crimped or damaged. Examine the power cable periodically
for any defects. Do not immerse the device in water or other liquids. Do not install the device in a location where
flooding may occur. Do not use the device during thunderstorms. Disconnect the device from the electrical power supply
immediately.

Product code: 45041

6

Shark – The Meg – Hybrid One
WARNING Risk of epileptic shock
Strobe lighting can trigger seizures in photosensitive epilepsy. Sensitive persons should avoid looking at strobe lights.
CAUTION Risk of injury due to movement of the device
The head of the device can move quickly. Persons staying near the device could be injured or frightened.
Make sure that there are no persons close to the device when you turn on the device and during operation. Keep body parts away from the moving parts of the device when servicing and during maintenance. Long hair or loose clothing can be entangled during the rotation of the moving head.
Attention Power supply
Before connecting the device to the power supply, make sure that the current, voltage and frequency match the input voltage, current and frequency specified on the information label on the device.
Make sure that the cross-sectional area of the extension cords and power cables is sufficient for the required power consumption of the device.
Attention General safety
Do not connect the device to a dimmer pack. Do not switch the device on and off in short intervals. This decreases the device’s life. Do not shake the device. Avoid brute force when installing or operating the device. Change the lens or the LEDs if they are visibly damaged to such an extent that their effectiveness is
impaired, for example by cracks or deep scratches. Contact your Highlite International dealer for more information, as servicing can be performed only by instructed or skilled persons. If the device is dropped or struck, disconnect the device from the electrical power supply immediately. If the device is exposed to extreme temperature variations (e.g. after transportation), do not switch it on immediately. Let the device reach room temperature before switching it on, otherwise it may be damaged by the formed condensation. If the device fails to work properly, discontinue the use immediately.
Attention For professional use only This device shall be used only for the purposes it is designed for.
This device is designed to be used as a professional moving head. Any incorrect use may lead to hazardous situations and result in injuries and material damage.

Product code: 45041

7

Shark – The Meg – Hybrid One
This device is not suitable for households and for general lighting. This device is not designed for permanent operation. This device does not contain user-serviceable parts. Unauthorized modifications to the device will
render the warranty void. Such modifications may result in injuries and material damage.
Attention Before each use, examine the device visually for any defects.
Make sure that:
All screws used for installing the device or parts of the device are tightly fastened and are not corroded.
The safety devices are not damaged. There are no deformations on housings, fixations and installation points. The lens is not cracked or damaged. The power cables are not damaged and do not show any material fatigue.
Attention Do not expose the device to conditions that exceed the rated IP class conditions.
This device is IP20 rated. IP (Ingress Protection) 20 class provides protection against solid objects greater than 12 mm, such as fingers, and no protection against harmful ingress of water.
Requirements for the User
This product may be used by ordinary persons. Maintenance may be carried by ordinary persons. Installation and service shall be carried out only by instructed or skilled persons. Contact your Highlite International dealer for more information.
Instructed persons have been instructed and trained by a skilled person, or are supervised by a skilled person, for specific tasks and work activities associated with the installation, service and maintenance of this product, so that they can identify risks and take precautions to avoid them.
Skilled persons have training or experience, which enables them to recognize risks and to avoid hazards associated with the installation, service and maintenance of this product.
Ordinary persons are all persons other than instructed persons and skilled persons. Ordinary persons include not only users of the product but also any other persons that may have access to the device or who may be in the vicinity of the device.

Product code: 45041

8

Shark – The Meg – Hybrid One
3. Description of the Device
The Showtec Shark – The Meg – Hybrid One is a compact but powerful 160 Watt LED hybrid moving head with a beam angle that can be adjusted from Beam to Spot to Wash (motorised zoom from 3,8 to 15,8 degrees). It is suitable for indoor applications and comes with a lot of impressive effects. It is equipped with a colour wheel with 9 dichroic colours plus open and it has two gobo wheels, one with 7 rotating gobos plus open, and one with 12 fixed gobos plus open. It has an indexed, rotatable 3-facet prism, and frost and motorised focus functions. The Shark – The Meg – Hybrid One can be controlled through DMX and has several built-in programs for stand-alone operation.
Front View

  1. Lens / 1x 160 W CW LED module 02) Signal LED 03) Built-in microphone 04) TFT display 05) Control buttons

Fig. 02

Product code: 45041

9

Shark – The Meg – Hybrid One Back View

  1. 3-pin DMX signal connector IN 07) 3-pin DMX signal connector OUT 08) Power switch (ON / OFF) 09) Power Pro connector IN (Blue) 10) Power Pro connector OUT (Grey) 11) Fuse F4AL / 250 V

Bottom View

Fig. 03
12) Mounting openings for quick lock bracket 13) Mounting opening for safety eye

Product code: 45041

Fig. 04 10

Shark – The Meg – Hybrid One

Product Specifications

Model:

Shark – The Meg – Hybrid One

Electrical: Input voltage: Power consumption: Fuse:

100­240 V AC, 50/60 Hz 200 W F4AL, 250 V

Physical: Dimensions: Weight:

262 x 165 x 439 mm (L x W x H) (including bracket) 9,85 kg

Optics: Light source: Dimmer: Focus: Frost: Prism: Dynamics effects: Beam angle Circular: Strobe: Lux @2m Lux @3m Lux @5m Lumen Total: CRI: Dichroic Colour Wheel 1 Gobo Wheel 1
Gobo Wheel 2 Pan: Tilt

1x 160 W White LED module 0­100 % Motorized Frost filter 3-facet Prism Rotate 3,8°­15,8° 0­20 Hz 175844 lx 78153 lx 28135 lx 3075 lm 73 9 + open 7 + Open: 2 glass gobos: diameter 14 mm, image size 9 mm, thickness 1,2 mm 5 metal gobos: diameter 14 mm, image size 9 mm, thickness 0,3 mm 12 + Open 540 ° 270 °

Operation and control: Control:
DMX channels:
Control panel:

Stand-alone (Auto, Built-in Programs, Manual) Master/Slave DMX-512 8 channels 16 channels 18 channels TFT display and buttons

Connections: Power connections: Data connections: Signal pinouts:

Power Pro connectors IN/OUT 3-pin DMX connectors IN/OUT Pin 1 (ground), pin 2 (-), pin 3 (+)

Construction: Housing: Color: IP rating: Cooling:

Metal / PVC Black IP20 Axial Fan

Thermal: Minimum ambient temperature ta: Maximum ambient temperature ta:
Minimum distance: Minimum distance from flammable surfaces: Minimum distance to lighted object:

0 °C 45 °C
0,8 m 0,8 m

Product code: 45041

11

Shark – The Meg – Hybrid One Dimensions

Fig. 05

Fig. 06

Product code: 45041

Fig. 07 12

Fig. 08

Shark – The Meg – Hybrid One
4. Installation
Safety Instructions for Installation
WARNING Incorrect installation can cause serious injuries and damage of property.
If trussing systems are used, installation must be carried out only by instructed or skilled persons. Follow all applicable European, national and local safety regulations concerning rigging and trussing.
Personal Protective Equipment
During installation and rigging wear personal protective equipment in compliance with the national and site-specific regulations.
Installation Site Requirements
The device can be used only indoors. The device can be mounted to a truss or other rigging structure in any orientation. The minimum distance between the light output and the illuminated surface must be bigger
than 0,8 m. The maximum ambient temperature ta = 45 °C must never be exceeded.

Product code: 45041

13

Shark – The Meg – Hybrid One
Rigging
The device can be positioned on a flat surface or mounted to a truss or other rigging structure in any orientation. Make sure that all loads are within the pre-determined limits of the supporting structure.
CAUTION Restrict the access under the work area during rigging and/or derigging.
To mount the device, follow the steps below: Fasten the quick lock bracket, supplied with the device, on the mounting openings for quick lock bracket (12), as shown in Fig. 09

Fig. 09
Attach the device to the supporting structure. Make sure that the device cannot move freely. Secure the device with a secondary suspension, for example a safety cable. Make sure that the secondary suspension can hold 10 times the weight of the device. If possible, the secondary suspension should be attached to a supporting structure independent of the primary suspension. Put the safety cable through the safety eye as shown in Fig. 09.

Product code: 45041

14

Shark – The Meg – Hybrid One
Connecting to Power Supply
DANGER Electric shock caused by short-circuit
The device accepts AC mains power at 100­240 V and 50/60 Hz. Do not supply power at any other voltage or frequency to the device.
This device falls under IEC protection class I. Make sure that the device is always electrically connected to the ground (earth).
Before connecting the device to the socket-outlet: Make sure that the power supply matches the input voltage specified on the information label on
the device. Make sure that the socket-outlet has ground (earth) connection.
Connect the device to the socket-outlet with the power plug. Do not connect the device to a dimmer circuit, as this may damage the device.
Power Linking of Multiple Devices
This device supports power linking. Power can be relayed to another device via the power OUT connector. Note that the input and the output connectors have different designs: one type cannot be connected to the other.
Power linking of multiple devices must be carried out only by instructed or skilled persons.
WARNING Incorrect power linking may lead to overload of the electrical circuit and result in serious injuries and damage of property.
To prevent overload of the electrical circuit, when power linking multiple devices:
Use cables with sufficient current-carrying capacity. The power cable supplied with the device is not suitable for power linking of multiple devices.
Make sure that the total current draw of the device and all connected devices does not exceed the rated capacity of the power cables and the circuit breaker.
Do not link more devices on one power link than the maximum recommended number.
Maximum recommended number of devices: at 100­120 V: 4 devices Shark – The Meg – Hybrid One at 200­240 V: 8 devices Shark – The Meg – Hybrid One

Product code: 45041

15

Shark – The Meg – Hybrid One
5. Setup
Warnings and Precautions
DANGER Electric shock caused by short-circuit
Attention Connect all data cables before supplying power. Disconnect power supply before connecting or disconnecting data cables.
Stand-alone Setup
When the Shark – The Meg – Hybrid One is not connected to a controller or to other devices, it functions as a stand-alone device. For more information about the control modes, refer to 6.2. Control Modes on page 19.
DMX Connection
DMX-512 Protocol You need a DMX serial data link to run light shows of one or more devices using a DMX-512 controller or to run synchronized shows of two or more devices set in a master/slave control mode. The Shark – The Meg – Hybrid One has 3-pin DMX signal IN and OUT connectors. The pin assignment is as follows: 3-pin: pin 1 (ground), pin 2 (-), pin 3 (+) Devices on a serial data link must be daisy-chained in a single line. The number of devices that you can control on one data link is limited by the combined number of the DMX channels of the connected devices and the 512 channels available in one DMX universe. To comply with the TIA-485 standard, no more than 32 devices should be connected on one data link. In order to connect more than 32 devices on one data link, you must use a DMX optically isolated splitter/booster, otherwise this may result in deterioration of the DMX signal. Note: Maximum recommended DMX data link distance: 300 m Maximum recommended number of devices on a DMX data link: 32 devices

Product code: 45041

16

Shark – The Meg – Hybrid One
DMX Cables Shielded twisted-pair cables with 3-pin XLR connectors must be used for reliable DMX connection. You can purchase DMX cables directly from your Highlite International dealer or make your own cables. If you use 3-pin XLR audio cables for DMX data transmission, this may lead to signal degradation and unreliable operation of the DMX network. When you make your own DMX cables, make sure that you connect the pins and wires correctly as shown in Fig. 10.
Fig. 10 Master/Slave Setup The Shark – The Meg – Hybrid One supports master/slave control mode. To connect multiple devices in a master/slave setup, follow the steps below: Connect the first device’s DMX OUT connector to the second device’s DMX IN connector with a 3-pin DMX cable. The first connected device in the setup will be automatically recognized as the master device. Repeat step 1 to connect all devices as shown in Fig. 11. Set all subsequent devices in the setup as slave devices. See 6.6.1. DMX Functions on page 26 for more information. Connect a DMX terminator (120 resistor) to the DMX OUT connector of the last device in the setup.

Product code: 45041

17

Fig. 11

Shark – The Meg – Hybrid One
DMX Linking
To connect multiple devices on one DMX data link, follow the steps below:

  1. Use a 3-pin DMX cable to connect the DMX OUT connector of the lighting controller to the DMX IN connector of the first device.
  2. Connect the first device’s DMX OUT connector to the second device’s DMX IN connector with a 3-pin DMX cable.
  3. Repeat step 2 to connect all devices in a daisy-chain as shown in Fig. 12.
  4. Connect a DMX terminator (120 resistor) to the DMX OUT connector of the last device on the data
    link.

Fig. 12
DMX Addressing
In a setup with multiple devices, make sure that you set the DMX starting address of each device correctly. The Shark – The Meg – Hybrid One has 3 personalities: 8 channels, 16 channels and 18 channels.
If you want to connect multiple devices on one data link and use them in 18-channel mode, for example, follow the steps below:
Set the starting address of the 1st device on the data link to 1 (001). 02) Set the starting address of the 2nd device on the data link to 19, as 1 + 18 = 19. 03) Set the starting address of the 3rd device on the data link to 37, as 19 + 18 = 37. 04) Continue assigning the starting addresses of the remaining devices by adding each time 18 to the
previous number.
Make sure that you do not have any overlapping channels in order to control the Shark – The Meg Hybrid One correctly. If two or more devices are addressed similarly, they will work similarly.

Product code: 45041

18

Shark – The Meg – Hybrid One
6. Operation
Safety Instructions for Operation

Attention This device must be used only for the purposes it is designed for.

This device is intended for professional use as a moving head. It is not suitable for households and for general lighting.
Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.

Attention Power supply

Before connecting the device to the power supply, make sure that the current, voltage and frequency match the input voltage, current and frequency specified on the information label on the device.

Control Modes

The Shark – The Meg – Hybrid One can be operated with a DMX controller, or without a DMX controller as a stand-alone device or in a master/slave setup.

The Shark – The Meg – Hybrid One supports the following control modes:

Stand-alone: Master/Slave: DMX-512:

Auto Run, Music Run Auto Run, Music Run 3 channel modes (8, 16 and 18 channels)

For more information about how to connect the devices, refer to 5. Setup on pages 16­18.

In auto operation mode you can run the auto program or one of the 9 built-in auto programs.

To run one of the 9 programs without a DMX controller, activate Programs menu. See 6.6.1.3. Auto Run on page 27 for more information.

For more information about sound-controlled operation mode see 6.6.1.4. Music Run on page 28.

To operate the device with a DMX controller:

  1. Set the DMX starting address of the device in the DMX Address menu. See 6.6.1.1. DMX Address on page 26 for more information.
  2. Select the DMX channel mode in the DMX Configuration menu. See 6.6.1.2. Channel Mode on page 27 for more information. See 6.7. DMX Channels on pages 32­34 for complete overview of all DMX channels.

Product code: 45041

19

Shark – The Meg – Hybrid One Control Panel

A) TFT DISPLAY B) MENU button C) UP button D) DOWN button E) ENTER button

Fig. 13
Use the MENU button to open the main menu or to exit the current submenu and return to the main menu.
Use the UP/DOWN buttons to navigate through the menus or to increase/decrease numeric values. Use the ENTER button to open the desired menu, to confirm your choice or to set the currently
selected value.
Start-up
Upon start-up the display shows a splash screen, indicating the device is resetting.
Afterwards the display shows the start screen. The start screen provides information about the temperature of the LEDs, the DMX starting address of the device, and the selected DMX channel mode:

Press the ENTER button or the UP/DOWN buttons to enter the main menu.
Note:
If no button is pressed, after 25 seconds of inactivity the display will turn off. Press any button to turn the display on.

Product code: 45041

20

Shark – The Meg – Hybrid One Menu Overview

Product code: 45041

21

Shark – The Meg – Hybrid One

Product code: 45041

22

Shark – The Meg – Hybrid One

Product code: 45041

23

Shark – The Meg – Hybrid One

Product code: 45041

24

Shark – The Meg – Hybrid One

Product code: 45041

25

Shark – The Meg – Hybrid One
Main Menu Options
The main menu has the following options:

  1. Press the UP/DOWN buttons to scroll through the following 4 main menu options:

DMX Address:

See 6.6.1. DMX Functions for more information.

Mode:

See 6.6.2. Fixture Setting for more information.

DMX Fail:

See 6.6.3. Manual for more information.

View DMX Value: See 6.6.4. Advanced for more information.

  1. Press the ENTER button to open the submenus.

DMX Functions

In this menu you can configure the Function settings of the device.

  1. Press the UP/DOWN buttons to scroll through the following options:

DMX Address:

See 6.6.1.1. DMX Address

Channel Mode: See 6.6.1.2. Channel Mode

Auto Run:

See 6.6.1.3. Auto Run

Music Run:

See 6.6.1.4. Music Run

  1. Press the ENTER button to open the submenus.

DMX Address

In this menu you can set the DMX starting address of the device.

Press the UP/DOWN buttons to select the DMX starting address of the device. The selection range

depends on the active DMX channel mode:

8 CH:

001­505

16 CH:

001­497

18 CH:

001­495

Press the ENTER button to save the changes.

Product code: 45041

26

Shark – The Meg – Hybrid One
Channel Mode In this menu you can choose a DMX configuration. 01) Press the UP/DOWN buttons to choose 8, 16 or 18 DMX channels. The display shows:

  1. Press the ENTER button to confirm the desired Channel Mode. Auto Run
    In this menu you can set the Auto Run mode of the device. 01) Press the UP/DOWN buttons to select the Auto Run mode. The display shows:

  2. Press the ENTER button to open the submenus. The display shows:

  3. Press the UP/DOWN buttons to select one of the 9 options: Program 1­9 04) Press the ENTER button to open the second submenu. The display shows:

  4. Press the UP/DOWN buttons to select one of 2 options:

Alone:

used for Stand-alone setting

Master:

used for Master-Slave setting

  1. Press the ENTER button to confirm your choice.

Product code: 45041

27

Shark – The Meg – Hybrid One
Music Run In this menu you can set the sound-controlled mode of the device.

  1. Press the UP/DOWN buttons to select the Music Run mode. The display shows:

  2. Press the ENTER button to open the submenus. The display shows:

  3. Press the UP/DOWN buttons to select one of the 9 options: Program 1­9 04) Press the ENTER button to open the second submenu. The display shows:

  4. Press the UP/DOWN buttons to select one of 2 options:

Alone:

used for Stand-alone setting

Master:

used for Master-Slave setting

  1. Press the ENTER button to confirm your choice.

Product code: 45041

28

Shark – The Meg – Hybrid One
Fixture Settings In this menu you can set the settings of the device. 01) Press the UP/DOWN buttons to select the desired submenu. The display shows:

  1. Press the UP/DOWN buttons to scroll through the following 12 submenu options. The submenus are:

Reset default.

Press the UP/DOWN buttons to return to factory settings OFF/ON.

Signal Set:

No Function

Reverse Pan.

Press the UP/DOWN buttons to choose between OFF/ON.

Reverse Tilt.

Press the UP/DOWN buttons to choose between OFF/ON.

Select Pan:

Press the UP/DOWN buttons to set between 360°, 540°, 630°.

Select Tilt:

Press the UP/DOWN buttons to set between 90°, 180°, 270°.

Mic Sensitivity:

Sound sensitivity. Press the UP/DOWN buttons to set between 000­099,

from OFF to high sound sensitivity.

DMX Fail:

To adjust the behaviour of the device in case of a DMX signal error.

Press the UP/DOWN buttons to choose between OFF and ON. Choose OFF

and the device will blackout its output, when a DMX signal error occurs.

Choose ON and the device will fall back on the last properly working DMX

signal from before the DMX signal error, which ensures undisrupted

performance.

Scan Quick Mode: The 0-100% acceleration will speed up.

Half Colorwheel: Press the UP/DOWN buttons to choose between OFF/ON.

Focus:

Press the UP/DOWN buttons to choose between Mode1 (near) /Mode2 (far).

Reverse Display. Press the UP/DOWN buttons to choose between OFF/ON.

  1. Press the ENTER button to enter the desired submenu.

  2. Press the UP/DOWN buttons to adjust the values.

  3. Once you have adjusted the settings, press the ENTER button to save changes.

Product code: 45041

29

Shark – The Meg – Hybrid One
Manual In this menu you can set the settings of the device. 01) Press the UP/DOWN buttons to select the desired submenu. The display shows:

  1. Press the UP/DOWN buttons to scroll through the following 17 submenu options. The submenus are:

Pan:

Set the initial pan position.

Pan-Fine:

Set the initial pan-fine position.

Tilt:

Set the initial tilt position.

Tilt-Fine:

Set the initial tilt-fine position.

Move Speed:

Set the initial move speed value.

Color Wheel:

Set the initial color wheel position.

Gobo1 wheel:

Set the initial gobo1 wheel position.

Gobo1 Rot:

Set the initial rotation position of gobo1 wheel.

Gobo2 wheel:

Set the initial gobo2 wheel position.

Strobe:

Set the initial strobe value.

Dimmer:

Set the initial dimmer value.

Focus:

Set the initial focus value.

Prism:

Set the initial Prism position.

Frost:

Set the initial frost value.

Color Time:

Set the initial color time value.

Gobo Time:

Set the initial gobo time value.

  1. Press the ENTER button to enter the desired submenu.

  2. Press the UP/DOWN buttons to adjust the values.

  3. Once you have adjusted the settings, press the ENTER button to save changes.

Product code: 45041

30

Shark – The Meg – Hybrid One
Advanced In this menu you can view the status of the device and set the calibration settings of the device.

  1. Press the UP/DOWN buttons to set the code to: 088. 02) Press the ENTER button to enter the desired submenu. The display shows:

  2. Press the ENTER button to enter the calibration submenu.

  3. Press the UP/DOWN buttons to scroll through the following 8 submenu options. The submenus are::

Pan:

Set the initial pan position.

Tilt:

Set the initial tilt position.

Color Wheel:

Set the initial color wheel position.

Gobo1 wheel:

Set the initial gobo1 wheel position.

Gobo2 wheel:

Set the initial gobo2 wheel position.

Focus:

Set the initial focus value.

Zoom:

Set the initial zoom value.

Prism:

Set the initial Prism position.

  1. Press the ENTER button to enter the desired submenu.

  2. Press the UP/DOWN buttons to adjust the values.

  3. Once you have adjusted the settings, press the ENTER button to save changes.

  4. You can also view the UID, the temperature and the current software version.

UID: No Function

Temperature: See the current temperature of the LED.

Ver: See the current software version

Product code: 45041

31

Shark – The Meg – Hybrid One

DMX Channels
8 Channels, 16 Channels, 18 Channels

8 CH 1 2
3 4
5

16 CH 1 2 3 4 5 6 7
8
9

18 CH 1 2 3 4 5 6 7
8
9

Function Pan Pan Fine Tilt Tilt Fine Pan/Tilt Speed Master Dimmer Shutter
Color wheel (Half color Mode)
Gobo wheel 1

Value Setting

000­255 000­010 000­255 000­255 000­225 226­235
236­245
246­255 000­255 000­031 032­063 064­095 096­127 128­144 145­159 160­191 192­223 224­255 000­004 005­009 010­014 015­019 020­024 025­029 030­034 035­039 040­044 045­049 050­054 055­059 060­064 065­069 070­074 075­079 080­084 085­089 090­127 128­189 190­193
194­255
000­009 010­019 020­029 030­039 040­049 050­059 060­069 070­079 080­099 100­119

Pan adjustment 0°­540° Pan adjustment, 16-bit Tilt adjustment 0°­210° Tilt adjustment, 16-bit From fast to slow Blackout during Pan/Tilt movement Blackout during Color wheel movement/gobo wheel 1 + 2 movement No function From low to high intensity (0­100 %) Shutter closed Shutter open Linear strobe, from low to high frequency (0­25 Hz) Shutter open Pulse strobe, from slow to fast Pulse strobe, from fast to slow Shutter open Random strobe, from slow to fast Shutter open Open Open + Color 1 Color 1 Color 1 + Color 2 Color 2 Color 2 + Color 3 Color 3 Color 3 + Color 4 Color 4 Color 4 + Color 5 Color 5 Color 5 + Color 6 Color 6 Color 6+ Color 7 Color 7 Color 7 + Color 8 Color 8 Color 8 + Color 9 Color 9 Clockwise color flow (CW), from fast to slow Stop Counter-clockwise color flow (CCW), from slow to fast Open Gobo 1 Gobo 2 Gobo 3 Gobo 4 Gobo 5 Gobo 6 Gobo 7 Gobo 1 shake effect, from slow to fast Gobo 2 shake effect, from slow to fast

Product code: 45041

32

Shark – The Meg – Hybrid One

8 CH
6 7 8

16 CH 18 CH Function

10

10 Gobo rotation

11

11 Gobo wheel 2

12

12 Focus

13

13 Zoom

14

14

Prism (3-facet)

15

15 Frost

16

16

Channel Functions

Value Setting

120­139 140­159 160­179 180­199 200­219
220­255
000­003 004­127 128­131 132­255 000­009 010­019 020­029 030­039 040­049 050­059 060­069 070­079 080­089 090­099 100­109 110­119 120­129 130­137 138­145 146­153 154­161 162­169 170­177 178­185 186­193 194­201 202­209 210­217 218­225
226­255
000­255 000­255 000­005 006­127 128­189
190­193 194­255 000­199 200­255 000­019 020­029 030­039 040­079 080­084 085­087 088­090 091­093

Gobo 3 shake effect, from slow to fast Gobo 4 shake effect, from slow to fast Gobo 5 shake effect, from slow to fast Gobo 6 shake effect, from slow to fast Gobo 7 shake effect, from slow to fast Clockwise rotation (CW) gobo flow from slow to fast No Function Clockwise gobo rotation, from fast to slow Stop Counter-clockwise gobo rotation, from slow to fast Open Gobo 1 Gobo 2 Gobo 3 Gobo 4 Gobo 5 Gobo 6 Gobo 7 Gobo 8 Gobo 9 Gobo 10 Gobo 11 Gobo 12 Rotating Gobo 1 shake effect, from slow to fast Rotating Gobo 2 shake effect, from slow to fast Rotating Gobo 3 shake effect, from slow to fast Rotating Gobo 4 shake effect, from slow to fast Rotating Gobo 5 shake effect, from slow to fast Rotating Gobo 6 shake effect, from slow to fast Rotating Gobo 7 shake effect, from slow to fast Rotating Gobo 8 shake effect, from slow to fast Rotating Gobo 9 shake effect, from slow to fast Rotating Gobo 10 shake effect, from slow to fast Rotating Gobo 11 shake effect, from slow to fast Rotating Gobo 12 shake effect, from slow to fast Clockwise gobo wheel rotation (CW), from slow to fast Gradual focus adjustment, from near to far Gradual adjustment zoom, from small to big Prism Off Prism On (3-facet) Counter-clockwise Prism rotation (CCW), from fast to slow Stop Clockwise Prism rotation (CW), from slow to fast Frost Filter Off Frost Filter On No function No function No function No function Reset All motors after 3 seconds Reset Pan + Tilt after 3 seconds Reset Color wheel after 3 seconds Reset Gobo wheel after 3 seconds

Product code: 45041

33

Shark – The Meg – Hybrid One

8 CH 16 CH 18 CH Function
17 Color Time 18 Gobo Time

Value Setting

094­096 097­099 100­108 109­117 118­126 127­135 136­144 145­153 154­162 163­171 172­180 181­189 190­198 199­207 208­216 217­225 226­234 235­243 244­252 253­255 000­255 000­255

No function Reset other motors after 3 seconds Auto Program 1 Auto Program 2 Auto Program 3 Auto Program 4 Auto Program 5 Auto Program 6 Auto Program 7 Auto Program 8 Auto Program 9 Sound-controlled Program 1 Sound-controlled Program 2 Sound-controlled Program 3 Sound-controlled Program 4 Sound- controlled Program 5 Sound-controlled Program 6 Sound-controlled Program 7 Sound-controlled Program 8 Sound-controlled Program 9 Gradual time adjustment, from short to long Gradual time adjustment, from short to long

Note:

Make sure that Master Dimmer channel is open, to see the light output. When the Half Colorwheel settings in menu 6.6.2. Fixture Settings on page 29 has been set to OFF, the
colorwheel will only show entire colors and no split colors.

Product code: 45041

34

Shark – The Meg – Hybrid One Rotating Gobo Wheel, Static Gobowheel and Color Wheel

Fig. 14

Fig. 15

Fig. 16

Product code: 45041

35

Shark – The Meg – Hybrid One

7. Troubleshooting

This troubleshooting guide contains solutions to problems which can be carried out by an ordinary person. The device does not contain user-serviceable parts.

Unauthorized modifications to the device will render the warranty void. Such modifications may result in injuries and material damage.

Refer servicing to instructed or skilled persons. Contact your Highlite International dealer in case the solution is not described in the table.

Problem The device does not function at all The device responds erratically The device does not respond to DMX control
The device responds erratically to DMX control
No light or LEDs cut out intermittently

Probable cause(s) No power to the device
Primary fuse is blown
The factory settings of the device are changed The controller is not connected The signal is reversed. The 3-pin DMX OUT of the controller does not match the DMX IN of the device The controller is defective
Bad data link connection
The data link is not terminated with a 120 termination plug
Incorrect addressing In case of a setup with multiple devices, one of the devices is defective and disturbs data transmission on the link
LEDs are damaged
The power supply settings do not match local AC voltage and frequency

Solution Check if power is switched on and
cables are plugged in Replace the fuse. See 8.3.1. Replacing
the Fuse on page 37 Reset the device’s parameters to the
default factory settings. See 6.6.2. Fixture Settings on page 29 Connect the controller Install a phase-reversing cable between the controller and the device
Try using another controller Examine connections and cables.
Correct poor connections. Repair or replace damaged cables
Insert a termination plug in the DMX OUT connector of the last device on the link
Check address settings and correct, if necessary
To find out which device is defective, bypass one device at a time until normal operation is restored
Disconnect the device and contact your Highlite International dealer
Disconnect the device. Check the settings and correct, if necessary

Product code: 45041

36

Shark – The Meg – Hybrid One

Maintenance
Safety Instructions for Maintenance
DANGER Electric shock caused by dangerous voltage inside
Disconnect power supply before servicing or cleaning.
Preventive Maintenance
Attention Before each use, examine the device visually for any defects.
Make sure that: All screws used for installing the device or parts of the device are tightly fastened and are not
corroded. The safety devices are not damaged. There are no deformations on housings, fixations and installation points. The lens is not cracked or damaged. The power cables are not damaged and do not show any material fatigue.
Basic Cleaning Instructions The external lens of the device must be cleaned periodically in order to optimize the light output. The cleaning schedule depends on the conditions at the site where the device is installed. When smoke or fog machines are used at the site, the device will need more frequent cleaning. On the other hand, if the device is installed in well-ventilated area, it will need less frequent cleaning. To establish a cleaning schedule, examine the device at regular intervals during the first 100 hours of operation. To clean the device, follow the steps below:
Disconnect the device from the electrical power supply. Allow the device to cool down for at least 5 minutes. 03) Remove the dust collected on the external surface with dry compressed air and a soft brush. 04) Clean the lens with a damp cloth. Use a mild detergent solution. 05) Dry the lens carefully with a lint-free cloth. 06) Clean the DMX and other connections with a damp cloth.
Attention
Do not immerse the device in liquid. Do not use alcohol or solvents. Make sure that the connections are fully dry before connecting the device to the power supply and
to other devices.

Product code: 45041

37

Shark – The Meg – Hybrid One
Corrective Maintenance
The device does not contain user-serviceable parts Do not open the device and do not modify the device.
Refer repairs and servicing to instructed or skilled persons. Contact your Highlite International dealer for more information.
Replacing the Fuse
DANGER Electric shock caused by short-circuit
Do not bypass the thermostatic switch or fuses. For replacement use fuses of the same type and rating only.
Power surges, short-circuit or incorrect electrical power supply may cause a fuse to burn out. If the fuse burns out, the device will not function anymore. If this happens, follow the steps below.

  1. Disconnect the device from the electrical power supply. 02) Allow the device to cool down for at least 20 minutes. 03) Loosen the fuse cover with a screwdriver and remove the fuse holder. 04) If the fuse is brown or unclear, it is burned out. Remove the old fuse. 05) Insert a new fuse in the fuse holder. Make sure that the type and the rating of the replacement fuse
    are the same as the ones specified on the information label of the product.
  2. Replace the fuse holder in the opening and tighten the fuse cover.

Product code: 45041

38

Shark – The Meg – Hybrid One
9. Deinstallation, Transportation and Storage
Instructions for Deinstallation
WARNING Incorrect deinstallation can cause serious injuries and damage of property.
Let the device cool down before dismounting. Disconnect power supply before deinstallation. Always observe the national and site-specific regulations during deinstallation and derigging of the
device. Wear personal protective equipment in compliance with the national and site-specific regulations.
Instructions for Transportation
Use the original packaging to transport the device, if possible. Always observe the handling instructions printed on the outer carton box, for example: “Handle with
care”, “This side up”, “Fragile”.
Storage
Clean the device before storing. Follow the cleaning instructions in chapter 8.2.1. Basic Cleaning Instructions on page 37.
Store the device in the original packaging, if possible.

Disposal

Correct disposal of this product Waste Electrical and Electronic Equipment This symbol on the product, its packaging or documents indicates that the product shall not be treated as household waste. Dispose of this product by handing it to the respective collection point for recycling of electrical and electronic equipment. This is to avoid environmental damage or personal injury due to uncontrolled waste disposal. For more detailed information about recycling of this product contact the local authorities or the authorized dealer.

Approval

Check the respective product page on the website of Highlite International (www.highlite.com) for an available declaration of conformity.

Product code: 45041

39

Shark – The Meg – Hybrid One

Product code: 45041

40

Shark – The Meg – Hybrid One

Product code: 45041

41

Shark – The Meg – Hybrid One

Product code: 45041

42

©2023 Showtec

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals