crown WD-406 Water Dispenser Instruction Manual

crown WD-406 Water Dispenser

Product Information

Specifications:

• Model : WD-406
• Power Indicator : Yes
• Heating Indicator : Yes
• Cooling Indicator : Yes
• Water Shortage Indicator: Yes
• Hot Water Tap: Yes
• Normal Water Tap: Yes

Product Usage Instructions

Before Use:

1. Ensure the water faucet is open to allow water to pour out.
2. Turn on the drain valve to empty the water inside the product. Repeat this process three times.
3. Never change the power cord or extend its length.
4. If water flow is stuck, turn off the cold water switch for at least 4 hours.
5. To connect electricity for hot water, put on the hot water button until water flows out.

Warning:

• The plug base should be three-hole grounded with electricity leakage protection.
• Children are not allowed to play with the water faucet toprevent accidental burns.

Notice : Refer to the user manual for detailed instructions on the components and functions of the product.

Children should be supervised to ensure that they do not play with the appliance.” “If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard

CAUTION “This appliance is not intended for use by persons(including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety”

1. The services should be determined by factory and qualified person.
2. lf any damage of electrical connector, change the POWER CORD to avoid electrical shock from the center.

Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.

PART NAME

NOTES BEFORE USE

1. This machine is suitable for household and must be used indoors.
2. The machine should be stably placed on the floor, to avoid the damage because of the slide. Meanwhile, the back side of the water dispenser should keep at least 10CM space to the wall, for ventilation and heat radiation.
3. The machine should be placed in a dry, cool and ventilated place, also should avoid the sunlight’s irradiation and liquid’s splashing. Don’t be close to other expensive furniture and electrical equipment, never should be placed on the woods
4. When first in use, the user should clean the inside of the body. The specific method: Put a new bottom with fresh water into the water dispenser’s bottle support, press the cold and hot button until the water flows out of the faucet at the same time. 20 minutes later, pull the bottom out of water dispenser, press the water faucet to let the water pour out and also turn on the drain valve to empty the water inside. Do as the method above three times.
5. Never change the power cord and Never extend the length of the power cord.
6. lf the water can’t flow out because of stuck, please turn off the cold water switch backside until 4 hours.
7. Put on the hot water button until the water flows out, then it can connect the electricity.

WARNING

1. The plug base should be three-hole grounded with electricity leakage protection.
2. The children is not allowed to play with water faucet to avoid accidental burns.

NOTICE

1. Get rid of the bottom lid with tools.
2. Put the water bottom on the Salver, clean the pumping rod and connect the pumping rod with the bottom, smoothly put the salver inside the machine.
3. Connect the power cord with the plug base, the pumping will automatically pump. After the water flows out of the hot tap, turn on the heating switch, the heating indicator will be lighted, the machine starts heating. Turn on the cooling switch, the cooling indicator will be lighted, the machine starts cooling.
4. When there is no water, the machine will automatically alarm, with the sound of buzzers like bee bee. Meanwhile, the water shortage indicator will be lighted to remind you to change a new bottom.

TECH.DATA

CIRCUIT

ATTENTION AND MAINTENANCE

1. The first time to use water dispenser, Must connect water first, when the water comes out from the hot water faucet, then it can connect the electricity. Any case in electricity without water is forbidden.
2. Insert or Pull out the plug to start or turn off the water dispenser is forbidden
3. When do the cleanout or maintenance or the water dispenser stops to use in a long time, pull out the plug first. Meanwhile, when the hot water is cold, open the drain valve until no water is in the water dispenser.
4. The cleanout should be done timely to ensure the water quality.
5. The children should not allowed to play with the water faucet, or it will get burnt unexpected.

TROUBLESHOOTING

Please check the following before have the machine repaired.

FAQ

Q: How do I clean the product?
A: To clean the product, follow the cleaning instructions provided in the user manual. It is recommended to regularly clean the water taps and trays.

Q: What should I do if the water shortage indicator is on?
A: If the water shortage indicator is on, check the water source and refill the product with water as needed. Ensure proper water levels are maintained for optimal performance.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>