ELAC DCB41 ConneX Powered Speakers Owner’s Manual

June 3, 2024
ELAC

ELAC logo DCB41 ConneX Powered Speakers
Owner’s Manual
ELAC DCB41 ConneX Powered Speakers

DCB41

Contents – Contenu – InhaltELAC DCB41 ConneX Powered Speakers -
fig

Connections

ELAC DCB41 ConneX Powered Speakers - fig
1

  1. Connect speakers together with supplied wire
  2. Connect source – TV, Computer, Phono
  3. Connect Source – Bluetooth
  4. Connect AC mains

Controls and Inputs/Output

ELAC DCB41 ConneX Powered Speakers - fig
2

  1. AC Mains Inlet
  2. HDMI (ARC) Input
  3. Volume/Power/Source
  4. L/R switch
  5. USB for Update
  6. Ground Screw Terminal
  7. USB Input
  8. Optical Input
  9. SubWooofer Output
  10. Phono/Line Switch
  11. Line/Phono Input
  12. Speaker Output

The Volume knob can be used to adjust volume, change input and power on/off.
Rotate: Rotating the knob will increase or decrease volume.
Push:
Press to turn on unit.
Press and hold in BT input to initiate pairing
Press when on to change input. Front LED colours are:
[BT – Blue] [HDMI – Green] [USB – White] [Optical – Red] [Phono – Pink]

CONNECTIONS – TURNTABLE

ELAC DCB41 ConneX Powered Speakers - fig
3

Note: Some turntables have built in pre-amplifiers that can be disabled. Ensure the turntable pre-amplifier is set to Off and DCB41 is set to ON.
If you choose to use the turntable’s Phono pre-amplifier, then ensure its switch is set to ON postion and DCB41 is set to OFF.
The Ground connection is optional. It is recommended to be used as it can lower residual noise.

CONNECTIONS – TELEVISION

ELAC DCB41 ConneX Powered Speakers - fig
4

Note: HDMI supports eARC and ARC inputs from most televisions.
Your television remote control can also control, power, mute and volume of your Debut ConneX.

CONNECTIONS – SUBWOOFER

ELAC DCB41 ConneX Powered Speakers - fig
5

CONNECTIONS – COMPUTER

ELAC DCB41 ConneX Powered Speakers - fig
6

Connect to your USB devices USB Type B cable (printer cable)

CONNECTIONS – BLUETOOTH ****

When initial power up – BT LED will flash if nothing is paired to it.
When LED is flashing, “ELAC DCB41” is vissible on your device.
Pairing can also be initited as follows:
Press and hold BT source on remote until LED flashes.
Press and hold rear volume button when in BT input until LED flashes

REMOTE CONTROL

ELAC DCB41 ConneX Powered Speakers - fig
7

SETTING LEFT or RIGHT SPEAKERELAC DCB41 ConneX Powered Speakers - fig
8

The L/R switch is in reference to speaker output terminals.
If L/R switch is set to “L” then the speaker output will be the LEFT speaker.
IF L/R switch is set to “R” then the speaker output will be the RIGHT.

SAFETY INSTRUCTIONS

1. General information

  • Please read and follow these safety instructions.
  • Keep them safe for future reference.
  • Observe all warnings on the speaker and in the manual. Please check the speaker for damage before use. The speaker must be in perfect working condition. Damaged parts may lead to personal injury.

2. Use only as directed

  • Connect the speaker(s) according to the instructions in the manual.
  • Many ELAC speakers are equipped with spikes and/or anti-slip feet. They are explicitly provided for leveling the speaker. For leveling on an uneven floor, unscrew the  spikes or anti-slip feet by 2-3 turns of thread. The speaker should always be in perfect vertical alignment: the stability of the speaker must not be compromised by using spikes or anti-slip feet as the speaker may tip-over.

3. Location

  • Install the speakers on a level surface only
  • When choosing the location of these speakers do not place them in locations that are:
  • In direct sunlight
  • Very humid
  • Prone to vibrations
  • Exceptionally hot or cold
  • Near CRT Televisions (the speakers are not magnetically shielded and may cause color issues with a CRT based TV)
  • Close to magnetic cards (Since the speakers are not magnetically shielded placing magnetic cards such as credit cards or commuter cards may cause them to fail).

WARNING! Please ensure the product is perfectly stable to avoid injury from tip-over. Please note, that stability can be increased by using spikes on carpeted surfaces.  However, the mounting of spikes must be carried out carefully due to their very sharp ends which may cause injuries. The stability on slippery floors can be increased by using  Velcro fastening tape or double- sided adhesive tape. Do not install the speaker near any heat sources such as radiators, heating valves, stoves, or other apparatus  (including amplifiers) that produce heat, or in areas where there is a risk of explosion.

  • Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
  • Do not install the speaker in a closed rack or in a closed cupboard.
  • Do not put burning candles on or near the speaker.
  • Do not install the speaker near transformers because electromagnetic stray fields can cause hum noise on woofers.
  • In combination with certain materials / lacquers / material surfaces, anti-slip feet or spike washers may cause colored imprints on the surfaces.

4. Overload
Extreme overload of the device due to very high volume may cause individual components to blow.
Because of the possible danger, you should never leave loudspeakers under extreme overload conditions unattended.
5. Service
DANGER! Do not open the cabinet because the components and conductors may carry dangerous levels electricity! Servicing to be carried out by qualified service personnel only.
Servicing is required when the loudspeaker has been damaged in any way, such as damage to the power supply cord or the plug, or when liquid has been spilled or objects  have fallen into the loudspeaker, the speaker has been exposed to rain or moisture, does not operate normally, or has been dropped. To reduce the risk of electric shock, do  not open the loudspeaker. Servicing to be carried out by qualified service personnel only.
6. Fuse links
Various faults in subwoofers or active speakers may cause the fuse to blow. If the fuse blows, only replace it with the correct fuse type and rating as shown on the rear of the  loudspeaker on the fuse holder. A second fuse is included with the device (in the fuse holder beneath the main socket).
7. Cleaning
NOTE: Clean only with soft, smooth cloth or with dust brush. Do not use scouring agents, alcohol, benzene, furniture polish or other agents for cleaning! Modern furniture  is often coated with multiple varnishes and plastics which can be treated with chemical agents. Some of these agents contain substances which degrade or soften the rubber  feet. Therefore we advise you to place an anti-slip mat underneath the loudspeaker.
8. Volume
CAUTION! Continuous high volume may cause severe damage to your hearing. Please listen responsibly.
9. Disposal
The packaging is made from recyclable materials. Dispose of this in an environmentally friendly manner. At end of life do not dispose the speaker with the standard  household waste. The speaker must be recycled in accordance with local legislation. Ask your local government for further information on recycling as the device contains  valuable raw materials. Disable the speaker before disposal.
10. Power
This subwoofer is only intended to be connected to voltages that are listed on the rear panel of the cabinet. Connection to any other voltage may cause irreversible damage to  the subwoofer and will void the warranty. Use of plug adapters is not recommended because they may allow connection to voltages other than those printed on the back of this subwoofer.

Philosophy
Thank you for purchasing this ELAC product.
Since the time we started (1926), ELAC has always striven to achieve the very best.
Your new ELAC speakers are built to the highest standards using high-quality components that are carefully constructed to deliver the best-in-class sound quality. They are  developed by a passionate group of individuals whose soul purpose is to bring a new dimension of sound quality into your home. Enjoy!

Before Use

  • Avoid damage to the speakers and other components:

  • Carefully unbox the speakers carefully to avoid physically damaging your speakers.

  • Use appropriate gauge wires (minimum of 14 gauge wire for runs up to 25 feet).

  • Make sure wire polarity is connected correctly. Most speaker cables are coded for ease of use.
    Make sure positive (red) connection on the amplifier terminal is connected to the positive (red) on your speakers. Follow the same instructions for the negative side. Strip  off approximately 1/2”of the insulation from the ends of the speaker cable, twist the bare strands and insert into the binding post.

  • Ensure your equipment is turned off before connecting speakers.

  • Check to ensure positive and negative wires are not touching each other once they’re connected to the speaker terminals.

ELAC logo ELAC AMERICAS INC.
1938 N. BATAVIA St. SUITE K ORANGE, CA 92865
ELAC ELECTROACUSTIC GMBH
FRAUNHOFERSTRAßE 16 D-24118 KIEL, GERMANY

Connections

ELAC DCB41 ConneX Powered Speakers - fig
9

  1. Connect speakers together with supplied wire
  2. Connect source – TV, Computer, Phono
  3. Connect source – Bluetooth
  4. Connect AC mains

Safety Instructions

1. General information

  • Please read and follow these safety instructions.
  • Keep them safe for future reference.
  • Observe all warnings on the speaker and in the manual. Please check the speaker for damage before use. The speaker must be in perfect working condition. Damaged parts may lead to personal injury.

2. Use only as directed

  • Connect the speaker(s) according to the instructions in the manual.
  • Many ELAC speakers are equipped with spikes and/or anti-slip feet. They are explicitly provided for levelling the speaker. For levelling on an uneven floor. unscrew the spikes or anti-slip feet by 2-3 turns of thread The speaker should always be in perfect vertical alignment: the stability of the speaker must not be compromised by using spikes or anti-slip feet as the speaker may tip-over.

3. Location

  • Install the speakers on a level surface only
  • When choosing the location of these speakers do not place them in locations that are:
  • In direct sunlight
  • Very humid
  • Prone to vibrations
  • Exceptionally hot or cold
  • Near CRT Televisions (the speakers are not magnetically shielded and may cause color issues with a CRT based TV)
  • Close to magnetic cards (Since the speakers are not magnetically shielded placing magnetic cards such as credit cards or commuter cards may cause them to fail).

WARNING! Please ensure the product is perfectly stable to avoid Injury from tip-over. Please note, that stability can be increased by using spikes on carpeted surfaces. However. the mounting of spikes must be carried out carefully due to their very sharp ends which may cause injuries. The stability on slippery floors can be increased by using Velcro fastening tape or double- sided adhesive tape. Do not install the speaker near any heat sources such as radiators. heating valves. stoves. or other apparatus (including amplifiers) that produce heat. or in areas where there is a risk of explosion.

  • Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
  • Do not install the speaker in a closed rack or in a closed cupboard.
  • Do not put burning candles on or near the speaker
  • Do not install the speaker near transformers because electromagnetic stray fields can cause hum noise on woofers.
  • In combination with certain materials/ lacquers/ material surfaces, anti-slip feet or spike washers may cause colored imprints on the surfaces.

4. Overload
Extreme overload of the device due to very high volume may cause damage to individual components. Because of the possible danger, you should never leave loudspeakers under extreme overload conditions unattended.
DANGER! Do not open the cabinet because the components and conductors may carry current! Servicing to be carried out by qualified service personnel only. Servicing is  required when the loudspeaker has been damaged in any way, such as damage to the power supply cord or the plug, or when liquid has been spilled or objects have fallen onto  the loudspeaker, the speaker has been exposed to rain or moisture, does not operate normally, or has been dropped. To reduce the risk of electric shock, do not open  the loudspeaker. Servicing should be carried out by qualified service personnel only.

6. Cleaning
NOTE: Clean only with soft, smooth cloth or with dust brush. Do not use scouring agents, alcohol, benzene, furniture polish or other agents for cleaning! Modern furniture  is often coated with multiple varnishes and plastics which can be treated with chemical agents. Some of these agents contain substances which degrade or soften the rubber  feet. Therefore we advise that you place an anti-slip mat underneath the loudspeaker(s).
7. Volume
CAUTION! Continuous high volume may cause severe damage to your hearing. Please listen responsibly.
8. Disposal
The packaging is made from recyclable materials. Dispose of this in an environmentally friendly manner. At end of life do not dispose of the speaker(s) with standard household waste. The speaker must be recycled in accordance with local legislation.
Ask your local government for further Information on recycling as the device contains valuable raw materials Disable the speaker(s) before disposal.

ELAC Americas Inc.
North America Limited Liability Warranty
Products purchased from non-authorized retailers DO NOT come with an ELAC Warranty.

Passive Speakers (No Built-in Amplifier)
ELAC Americas Inc. warrants to the original purchaser that this product be free from defects and or workmanship for a period of 3 (Three) years from the original date of  purchase. During this time peri­ od, repair or replacement of parts will be free of charge to the original owner (See below limitations).
Shipping to and return from the repair center will be the responsibility of the original purchaser.
Powered Subwoofers
ELAC Americas Inc. warrants to the original purchaser that this product be free from defects and or workmanship for a period of 3 {Three) years on the cabinet and speaker  driver and 1 (One) year on the amplifier from the original date of purchase. During this time period, repair or replacement of parts will be free of charge to the original owner  (See below limitations). Shipping to and return from the repair center will be the responsibility of the original purchaseL
Electronics (Non Speaker Products)
ELAC Americas Inc. warrants to the original purchaser that this product be free from defects and or workmanship for a period of 1 (One) years from the original date of  purchase. During this time period, repair or replacement of parts will be free of charge to the original owner (See below limitations).
Shipping to and return from the repair center will be the responsibility of the original purchaser.
If service is required
In the event that service is required, please contact ELAC America at 714-252-8843 or at customer­ service@elac.us to arrange for service or replacement. You will be responsible to provide proof of purchase (Copy or original sales receipt). Shipping to and from our repair center will be the responsi­ bility of the original purchaser.
Warranty Outside of North America
This warranty applies to products purchased in the United States and Canada. For warranty claims outside of North America please contact the local dealer/distributor in the country of purchase.

8-Stock (Reconditioned/Open Box) Product Warranty Limitations

ELAC Americas Inc. warrants to the original purchaser that this product be free from defects and or workmanship, unless otherwise stated in product description, for a  period of 90 days from the original date of purchase. During this time period, repair or replacement of parts will be free of charge to the original owner (See below  limitations). Shipping to and return from the repair center will be the responsibility of the original purchaser.

  • Warranty begins on the date of original purchase from an authorized ELAC Americas Inc. dealer.
  • Product is warranted only if used in home applications within the max power rating specified in this manual. Commercial use of this product 1s not warranted.
  • Product that has been modified or altered in anyway will not be warranted.
  • Product that has been abused or subjected to faulty equipment will not be warranted
  • Products with defaced or removed serial numbers will not be warranted.

ELAC logo Safety Instructions
& Warranty Information
Quick User Guidehttps://elac.com/lp/dcb41-support
OWNER’s MANUAL

Documents / Resources

| ELAC DCB41 ConneX Powered Speakers [pdf] Owner's Manual
DCB41 ConneX Powered Speakers, DCB41, ConneX Powered Speakers, ConneX Speakers, Speakers, DCB41 Speakers
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals