Aeotec Cam 360 User Manual

Aeotec Cam 360 User Manual

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quick start section.
Z-Wave ensures a reliable communication by reconfirming every message ( two- way communication ) and every mains powered node can act as a repeater for other nodes ( meshed network ) in case the receiver is0nt in direct wireless range of the transmitter. o
This device and every other certified Z-Wave device can be used together with any other certified Z-

Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info

Product Description

Just one look and you are home. With the Aeotec Cam 360
, you get a 360-degree view of your room at a glance. The SmartThings App can display a detail edview of what is going on at home at day or night. Advanced object detection intelligently senses motion to alert you at a moment”s notice and differentiates between a person and an object.

A full HD camera delivers a clear, detailed view, allowing you to monitor your home 24 hours a day from your mobile devices. This way you know what is going on when you are not at home.
Full HD, high dynamic range and night vision show a clear, detailed view. Two- way audio and built-in microphone let you communicate with family members and pets.
With the SmartThings app, it is easy accessing your SmartThings Cam on Android and iOS devices. Sync with your phone or tablet and you will receive a preview clip whenever something is detected. Keep an eye on what matters, even when you are away. Get a clear detailed view of your home via multiple cameras right from your Samsung Smart TV, Samsung Family Hub, smartphone, or tablet

With the cloud storage-control, you can control up to four SmartThings cameras. Plus, you can watch rolling 24-hour recordings for free. All your footage is safelysecured in your personal cloud and can be accessed remotely any time.

Features

• 1080 FHD H.264
• 360° panoramic monitoring
• 96° vertical camera tilting
• Talk and listen via 2-way audio
• Movement detection
• Movement tracking
• 24 hours of free cloud storage
• NO Smart Home Hub
• or other Works as a SmartThings Hub additionally required
• 2,4 GHz WiFi IEEE 802.11 b/g/n
• Power supply: 5V/2A
• Regions: EU
• Certifications: FCC/IC/CE

Prepare for Installation / Reset

Please read the user manual before installing the product. In order to include (add) a Z-Wave device to a network it must be in factory default state.
Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country- specific installation guidelines/norms may do works with mains power. Prior to theassembly of the product, the voltage network has to be switched off and ensured against re-switching

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with thedevices of this network. This process is called Inclusion
.Devices can also be removed from a network. This process is called Exclusion Both processes are initiated by the primary controller of the Z-Wave network. Thiscontroller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

1. Make sure a device is in factory reset state before including. In doubt exclude before include.
2. If inclusion still fails, check if both devices use the same frequency.
3. Remove all dead devices from associations. Otherwise you will see severe delays.
4. Never use sleeping battery devices without a central controller.
5. Don,t poll FLIRS devices.
6. Make sure to have enough mains powered device to benefit from the meshing

Technical Data

Explanation of Z-Wave specific terms

• Controller is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wallcontrollers.
• Slave is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
• Primary Controller is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
• Inclusion is the process of adding new Z-Wave devices into a network.
• Exclusion is the process of removing Z-Wave devices from the network.
• Association is a control relationship between a controlling device and a controlled device.
• Wakeup Notification is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
  Node Information Frame is a special wireless message issued by a Z-Wave device to announce its capabilities and functions

(c) 2021 Z-Wave Europe GmbH, Anton str. 3, 09337 Hohenstein-Ernstthal, Germany, All rights reserved, www.zwave.eu. The template is maintained by Z-Wave Europe GmbH
. The product content is maintained by Z-Wave Alliance , Certification Team, christian@z-wavealliance.org. Last update of the product data: 08.03.202

Read More About This Manual & Download PDF:

References

• manuals-backend.z-wave.info/make.php?lang=en&sku=GP-AEOCAMEU&cert=
• Z-Wave Europe - The leading european distributor for Smart Home products.
• Z-Wave Europe - The leading european distributor for Smart Home products.
• Zwave - Aeotec

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>