Aeotec GP-AEOBTNUS Button for SmartThings User Guide

: October 30, 2023
: Aeotec

Table of Contents

Aeotec GP-AEOBTNUS Button for SmartThings
Introduction
Familiarize yourself with Aeotec Button
Package contents
Important safety information
Connect the Aeotec Button
Programming Aeotec Button
Factory reset your Aeotec Button
Aeotec Button technical specifications
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Aeotec GP-AEOBTNUS Button for SmartThings

Introduction

Aeotec Button was developed to control devices connected to Aeotec Smart Home Hub through the use of a physical and wireless button. It is powered by Aeotec Zigbee technology.

Aeotec Button must be used with an Aeotec Smart Home Hub in order to work.

Familiarize yourself with Aeotec Button

Package contents

Aeotec button
User manual
1x CR2 battery

Important safety information

Read, keep, and follow these instructions. Heed all warnings.
Clean only with a dry cloth.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce hear.
Only use attachments and accessories specified by the Manufacturer

Connect the Aeotec Button

Steps in SmartThings Connect

From the Home screen, tap the Plus (+) icon and select Device.
Select Aeotec and Remote/Button.
Tap Start.
Choose a Hub for the device.
Choose a Room for the device and tap Next.
While the Hub searches:

Pull the “Remove when Connecting” tab found in the sensor.
Scan the code on the back of the device.

Programming Aeotec Button

Aeotec Button supports 3 separate button presses that can be used in an Automation in your
Aeotec Smart Home hub. You can program the Aeotec button either from

Aeotec Button interface,
Custom Automation,
or SmartApps such as WebCoRE.

This section will go over how to program (1) Aeotec Button interface.

Steps in Smartthings Connect

From the Home screen, scroll down to your Aeotec Button and tap its widget.
Look for the 3 button press options and tap on any of them to program them.
• Single Press (Pressed)
• Double Pressed
• Held
Under “Then”, tap on Plus (+) icon.
Select one of the 2 options
• Control Devices
Select all devices you want to control
Tap Next
Tap on each device that you want to change the reaction.
• Run Scenes
1. Select all scenes you want this button press to run.
Tap Done
Test your button control by pressing the Aeotec Button.

Factory reset your Aeotec Button

Aeotec button can be factory reset at any time if you come across any issues, or if you need to repair Aeotec Button to another hub.

Steps in Smartthings Connect

Press and Hold the recessed connect button for five (5) seconds.
Release the button when the LED starts blinking red.
The LED will blink red and green while attempting to connect.
Use the Smartthings app and steps detailed in “Connect a Aeotec Button” above.

Aeotec Button technical specifications

This page lists Aeotec product technical specifications for Aeotec Button.
Name: Aeotec Button
Model number:
EU: GP-AEOBTNEU
US: GP-AEOBTNUS
AU: GP-AEOBTNAU
EAN: 4251295701677
UPC: 810667025458
Hardware required: Aeotec Smart Home Hub
Software required: SmartThings (iOS or Android)
Radio protocol: Zigbee
Power supply: No
Battery charger input: No
Battery type: 1 * CR2
Radio frequency: 2.4 GHz
Indoor/Outdoor use: Indoor only
Operating distance:
50 – 100 ft
15.2 – 40 m