Megger Multifunction Tester User Guide

June 7, 2024
Megger

Megger Logo

MFT70
Quick Start Guide

5 Commonwealth Ave
Woburn, MA 01801
Phone 781-665-1400
Toll-Free 1-800-517-8431

Visit us at www.TestEquipmentDepot.com

MEASURING VOLTAGE

Megger Multifunction Tester - Measuring Voltage

3 Press either TEXT button

When connecting to a live circuit, the voltage and frequency of supply is automatically displayed.

TEST THE PAIR FOR ALTERNATING CURRENT AND DIRECT CURRENT VOLTAGE

Megger Multifunction Tester - Tip to Ring

TIP to RING

Megger Multifunction Tester - Ring to Ground

RING to GROUND

Megger Multifunction Tester - Tip to Ground

TIP to GROUND

For all 3 setup configurations:

MEASURING CONTINUITY

Megger Multifunction Tester - Measuring Continuty 1

Megger Multifunction Tester - Measuring Continuty 2

Megger Multifunction Tester - Measuring Continuty 3

click the mode button to toggle the continuity buzzer ON/OFF

MEASURING INSULATION RESISTANCE

Megger Multifunction Tester - Measuring Insulation Resistance
1

Megger Multifunction Tester - Measuring Insulation Resistanc
2

**3**  Press and hold **TEST** button

To lock the test, hold down either TEST button, followed by either of the RED lock buttons below.
There’s a 500VDC MAX Insulation Resistance Voltage Testing as per Telecom Standards! The field pair must be OPEN at end of loop to properly conduct an insulation resistance test.

Megger Multifunction Tester - Measuring Insulation
Resistanc

To store your test results:

  1. Press lock & release
  2. Using the right test/lock buttons, scroll until the test you need is reached.
  3. Press lock & release again to display the remaining options & use the right buttons (above) to scroll again.
  4. Press lock & hold until ‘Str Ok’ is displayed.

MEASURING GROUND RESISTANCE

2-CLAMP STAKELESS

Testing Unbalance in Central Office, Hubs, and Head Ends

1   Set the left rotary switch to OFF

2

Megger Multifunction Tester - 2-Clamp Stakeless 2

Close the current clamp and then the voltage clamp around the conductor under test.
Make sure there’s a minimum separation of 100 mm (4 inches) between the current and voltage clamp.

Megger Multifunction Tester - 2-Clamp Stakeless 3

4  Press TEST and release

2-POLE

Megger Multifunction Tester - 2-Pole 1

Megger Multifunction Tester - 3-Pole 3.2

3   Press TEST and release

3-POLE

Megger Multifunction Tester - 3-Pole 1

Megger Multifunction Tester - 3-Pole 2

3   Press TEST and release

3-POLE

Megger Multifunction Tester - 3-Pole 1

Megger Multifunction Tester - 2-Pole 2

3   Press TEST and release

3-POLE

Megger Multifunction Tester - 3-Pole 3.1

Megger Multifunction Tester - 2-Pole 2

3   Press TEST and release

Ensure that the Megger Current Clamp jaw mating surfaces are free of dust and contamination!

3- POLE

Use this method if you’re working with concrete slabs or asphalt!

Megger Multifunction Tester - Add Water

Simple lay the probes on their sides and spray with water to make the connection.

Test Equipment Depot – 800.517.8431 – 5 Commonwealth Ave, MA 01801 – TestEquipmentDepot.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals