Rustic 810534677 2 Drawer TV Stand Instruction Manual

Rustic 810534677 2 Drawer TV Stand

CARE INSTRUCTIONS

1. DO NOT expose your product to any liquids. All liquids should be wiped up immediately with a soft, slightly damp cloth in the direction of wood grain.
2. DO NOT expose product to strong or direct sunlight, place near heat outlets or air conditioning units, open windows or dampness. Excessive exposure to sunlight and heat can cause furniture finish to fade. Extreme temperatures and humidity changes can cause wood to crack or split.
3. Clean periodically by wiping the product with a soft clean cloth.
4. DO NOT use abrasive chemicals for cleaning!
5. Do Not expose product to open flames or frayed or worn wiring. This could create conditions that could lead to serious injury or death.

MANUFACTURER:
DONGGUAN ZHENGSHENG METALS LTD.
ADD: DAPING VILLAGE, TANGXIA TOWN,DONGGUAN CITY,GUANDONG PROVINCE, CHINA.

WARNING!

• For use with televisions weighing (70) lbs (32Kg) or less. Use with heavier televisions may result in instability causing tip over resulting in death or serious injury!
• Death or serious injury may occur when children climb on audio and/or video equipment furniture. A remote control or toys placed on the furnishing may encourage a child to climb on the furnishing an, as a result, the furnishing may tip over on to the child.
• Relocating audio and/or video equipment to furniture not specifically designed to support audio and/or video equipment may result in death or serious injury due to the furnishing collapsing or over turning onto a child.

WARNING!

1. Recommend at least two people for assembly.
2. Assemble on a soft smooth surface to prevent damage to the finish.
3. DO NOT use power tools.

CAUTION!
This TV Stand is designed for flat panel LCD TVs. Top is intended for use with product screen measuring 55 to 60 inches and weighing no more than 70 pounds (31, 75kgs ). Use with other products may result in instability causing possible injury. Shelves are intended for use with a product weighing not more than 40 pounds (18.15kgs). Drawers may hold up to 20 pounds(9.0kgs) each.

MAINTENANCE
Check all bolts/screws periodically and tighten if necessay.

GENERAL BEST PRACTICES FOR ASSEMBLY

Read all instructions before starting
Clear a flat covered space to assemble
We recommend two people for assembly
Note that hardware required is provided for every step
Pay attention to orientation
Letter of the part corresponds to a sticker on the product
Number of the hardware corresponds to its number in the package Helpful hints provided along the way

MAINTENANCE:
Regularly check hardware and tighten if necessary

CARE AND CLEANING:
Clean periodically by wiping the product with a soft clean cloth
DO NOT use abrasive chemicals for cleaning

PARTS LIST

HARDWARE LIST

STEPS

STEP 1

Insert Half Thread Screw (4) into Left Frame (A) and fully tighten.

STEP2

Assemble Brake Block (19) and Caster (H) on Left Frame (A) with Carriage Bolts (2) and Nut (3) by using Spanner (18) and Phillips Screwdriver (Not Included).

STEP 3

Attach Middle Connect Bar (G) to Front Top Cross Bar (F) with Phillip Screw (5) by using Phillips Screwdriver (Not Included).

STEP 4

Attach Front Top Cross Bar (F) to Left Frame (A) with Allen Bolts (1) by using Allen Wrench {17) as shown in diagram.

STEP 5

Attach Front Bottom Cross Bar {C) to Left Frame {A) with Allen Bolt (1) by using Allen Wrench {17) as shown in the diagram.

STEP 6

Attach Back Bottom Cross Bar (D) to Left Frame (A) with Allen Bolt (1) by using Allen Wrench (17) as shown in diagram.

STEP 7

Place Back Panel (L) onto Ha f Thread Screw (4) in Left Frame (A). Attach to M ddle Connect Bar {G) with Phillip Screw (16) by using Phillips Screwdriver (Not Included) as
shown in diagram.

STEP 8

Insert Wood Dowel (7) into Back Vertical Panel (M). Align wood dowels in Back Vertical Panel (M) with holes in Back Panel (L) and insert. Attach Back Vertical Panel (M) to Back Bottom Cross Bar (D) with Phillip Screw (20) by using Phillips Screwdriver (Not Included).

STEP 9

Attach Vertical Middle Panel (N) to Middle Connect Bar (G) with Allen Screw (9) by using Allen Wrench (17) as shown in the diagram.

STEP 10

Attach Front Middle Cross Bar (E) to Middle Panel (J) with Phillip Screw (15) by using Phillips Screwdriver [Not Included) as shown in diagram.

STEP 11

Carefully place Middle Panel (J) into position on Left Frame (A) as shown in the diagram. Attach Middle Panel (J) to Left Frame (A) with Phillip Screw (15) by using Phillips Screwdriver (Not Included). Align the holes in Middle Panel (J) and Back Vertical Panel (M) and secure in place with Phillip Screw (8) by using Phillips Screwdriver (Not Included). Attach Middle Panel (N) to Back Panel (L) with Phillip Screw (8) by using Phillips Screwdriver (Not Included) as shown in diagram.

STEP 12

Insert Half Thread Screw (4) into Right Frame (B) and fully tighten.

STEP 13

Assemble Brake Block (19) and Caster (H) on Right Frame (B) with Carriage Bolt (2) and Nut (3) by using Spanner (18) and Phillips Screwdriver (Not Included).

STEP 14

Align the Half Thread Screw (4) and tabs on the Right Frame (B) with the Back Panel (L) and cross bars. Secure Right Frame (B) to Middle Panel (J) with Phillip Screw {15) by using Phillips Screwdriver (Not Included). Secure cross bars to Right Frame (B) with Allen Bolts (1) using Allen Wrench {17) as shown in the diagram.

STEP 15

Carefully place Bottom Panel (K) into position and secure in place with Phillip Screw {15) by using Phillips Screwdriver {Not Included) as shown in diagram.

STEP 16

Carefully set the assembled frame in the upright position. Insert small amount of Glue (10) into middle holes of the Left Frame (A), Right Frame (B) and Middle Panel (N) and insert Wood Dowel (7) as shown in the diagram.

STEP 17

Insert Cam (12} into Top Panel (I) and fully tighten. Insert small amount of Glue (10} into the three remaining holes as shown in the diagram.

STEP 18

Align the Cams (12) in Top Panel (I) with the holes in Left Frame (A), Right Frame (B) and Middle Panel (N) and lower into place. Insert Cam Locks (11) into the holes of Left Frame (A), Right Frame (B) and Middle Panel (N) as shown in the diagram. Fully tighten the Cam Locks (11) to secure the Top Panel (A) to the assembled frame.

STEP 19

Attach Drawer Left Panel {P) and Drawer Right Panel {Q) to Drawer Back {R) with Phillip Screw {6} by using Phillips Screwdriver {Not Included).
Note: The grooves in the Side Panels should align with the groove in the Back Panel.

STEP 20

Insert Cam (12) into Drawer Front Panel (O) by using Phillips Screwdriver (Not Included) and fully tighten.

STEP 21

Slide Drawer Bottom Panel (5) into the grooves of Drawer Left Panel (P) and Drawer Right Panel (Q) until it is fully inserted into Drawer Back Panel (R). Insert Cam Locks (13) into the holes of Drawer Left Panel (P) and Drawer Right Panel
(Q). Align the Cams in Drawer Front Panel with the holes in Drawer Left Panel (P) and Drawer Right Panel (Q) and slide into place until Drawer Bottom Panel (5) is fully inserted. Secure the Drawer Front Panel (O) to Drawer Left Panel (P) and Drawer Right Panel (Q) by turning the inserted Cam Locks (13) clockwise until tight.
Then attach Handle (T) to Drawer Front Panel (O) with Phillip Bolt (14) by using Phillips Screwdriver (Not Included) as shown in diagram.

STEP 22

Repeat STEP 19 through STEP 21 to assemble remaining drawer.

Insert the fully assembled drawers into the assembled frame.

STEP 23

YOUR TV STAND IS NOW READY

Documents / Resources

| Rustic 810534677 2 Drawer TV Stand [pdf] Instruction Manual
810372215, 810534678, 810534677, 2 Drawer TV Stand, 810534677 2 Drawer TV Stand, TV Stand, Stand
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>