EDIFIER Wireless Stereo Headphones User Guide

W830BT
Wireless Stereo Headphones
Operation Instructions

Introduction

Before use the headphone, please read these operating instructions carefully. Keep the operating instructions safe for future reference.

Features

• 40mm drivers deliver deep powerful bass ideal for all music genres
• 90-degree swivel ear pads optimise movement while ensuring overall comfort
• Bluetooth V4A supports HSP, HFP, A2DP and AVRCP protocol
• CSR8645 chip with MC and Qualcomm® apVCIA^ audio decoding technology
• Supports 95 hours of continuous play • Bluetooth connects up meters
• Sleek metal bracket and headband styled with soft leather ear caps and head cushion
• Accessories Include:
Travel case x 1
3.5mm audio cable x 1
USB charging cable x 1

Specifications

Bluetooth Version: Bluetooth V41
Bluetooth Profiles: HFP, HSP, A2DP, AVRCP
Audio Decoder: Qualcomm® aptXTM
Operating Distance: 10m
Operating Time: 95 hours
Charge Time: 4 hours
Standby Time: About 1500 hours
Rated Power Input: DC 5.0V=1A
Frequency Range: 20Hz-20KHz
Sensitivity (5P1): 96dB
Nominal Impedance: 24ohm

What’s in the Box

Operating Instraction

Diagram

1. Press: volume Increase /press and hold: next track
2. Multl-functIon key
3. Press: volume decrease/press and hold: previous track
4. micro USB charging port
5. 3.5mm audio Jack

II. Charge Batteries
The headset is equipped with a built-In rechargeable battery. Fully charge the battery before first use. While in use, the headset will beep and flash red light to Indicate battery low. You shall recharge the device.
1. Attach the USB charge cable to a standard USB power adapter.
2. Attach the charge cable to the Micro USB charge port on the headset.
3. Charge time: approximately 4 hours for a full charge.

Warning : The rechargeable batteries that provide power for this product must be disposed of properly for recycling. Do not dispose of batteries In fire to preventing an explosion.

Using the Headset

I. ON/OFF

quickly
OFF| Long press the multifunction key for 3 seconds| Indicator off

II. Connection
1. Bluetooth connection Please complete the connection with your mobile before use. Follow the steps below:
1.1. The distance between your mobile and the headset should be kept within 1 m. The closer the better.
1.2. Switch on the headset. Press and hold the multifunction key for 5 seconds to enter pairing mode.
1.3. Enable your mobile’s Bluetooth and search for Bluetooth devices. Select ‘EDIFIER W83OBT’ to pair. Once successfully paired, LED flashes blue slowly and you hear a prompt beep.

Note :
1. While in pairing state, If a connection cannot be established within 3 minutes, it will automatically exit the pairing mode;
2. If prompted for a passkey, enter ‘0000’;
3. Once successfully paired, the headset and your mobile will remember each other. When the headset is turned on again, It will connect to the last connected device automatically.

2. NFC connection
If your Bluetooth mobile supports NFC (Near Field Communication). enable your mobile’s NFC function first and switch on the headset. Then touch the NFC area of W83OBT with the NFC area of your mobile to pair your devices.
Note :
• When the mobile hibernates or is screen-locked, It cannot pair with NFC.
• The first time you try to pair, it requires keeping your mobile In touch with W830BT for slightly longer time. Walt till W83OBT entering the pairing mode before you take away the mobile.
• If no device is connected, you may use NFC to establish pairing; if a device is already connected, NFC function can also be used to disconnect.

3. Pair another device
The headset can simultaneously connect two Bluetooth devices. Follow the steps below:
3.1. Pair your headset with Device 1.
3.2. Switch off the headset. Long press the multi-function key to restart the headset and enter pairing mode. Conned device 2.
3.3. Now operate on device 1. Tap the headset In Bluetooth connection settings to connect and complete pairing with two devices;

Note : When two connected mobiles have different operating systems (e.g. One on Android and the other one on 10S), certain cross-system operations may show some delay (e.g. The song in mobile A will pause while play the song In mobile B). This Is considered normal.
Ill. Making Calls
1. Basic operations

Function| Headset status|

Operation

---|---|---
Answer a call| Incoming ring| Short press the multi-function key
Reject a call| Incoming ring| Long press the multi-function key for approx 2 seconds
End a call| Talking| Short press the multi-function key
Increase volume| Talking| Tap the volume + key
Decrease solume| Talking| Tap the volume – key
Direct a call to the mobile| Talking| Long press the multi-function key for approx 2 seconds
Direct a call to the headphone| Talking| Long press the multi-function key for approx. 2 seconds
Mute the mic| Talking| Long press the volume – key for approx. 2 seconds
Unmute| Talkin (with mic uted)| Long press the volume + key for approx 2 seconds
Call back last call| Device connected| Long press the multifunction key for approx. 2 seconds
Enable voice assistant| Device connected| Double press the multi-function key.

2. Three-way Calling

function key once
Answer new call and keep the current call on hold| Second incoming call| Tap the multi-function key twice
Switch between calls| Talkington hold)| Double-tap the multi-function key
End current call| Talklng(on hold)| Tap the multi-function key once

3. Calls with Two Mobiles Connected

multifunction key
End the current call and switch back to the mobile on hold| Talking with one call while the other call Is on hold| Tap the multifunction key once

IV. Play Music
1. Bluetooth audio mode
When the headset is connected to a mobile that supports Qualcomm® aptXTM, you may enjoy WWI music via the headphones:

Note : • When the headset is turned up to Its maximum volume, you will hear a prompt tone from the headset.
2. AUX-IN audio mode
The headset supports AUX IN audio input. Using 3.5mm to 3.5mm audio cable to connect the headset to a music player and enjoy the music online.
Note : • Plugging in a 3.5mm audio cable will turn off the headset and automatically disconnect the connection with the Bluetooth. AUX IN audio input is now in effect.
• If you want to go back to Bluetooth, unplug the 3.5mm audio cable and restart the headset to pair.

V. Restore factory setting
Headphone Is under power off and charging status, press and hold the Volume + key and volume – key simultaneously for about 3 seconds. The blue light flashes 3 times quickly. The factory settings are restored.
Note
• Once the factory settings are restored, the pairing list of the headphone Is erased. When you power on the headphone again, it will automatically begin the pairing process rather than automatic connecting. If it needs to connect a device, you will have to go through the pairing again.

Maintenance

• Do not place the product In wet places to avoid adverse effect to internal circuits of the product.
• Do not expose the product to direct sunlight or heat. The high temperature will shorten electronic components’ life, damage battery, and cause deformation of certain plastic parts.
• Do not expose the product to excessive cold to avoid damage to internal circuits.
• Do not attempt to disassemble the product. A non-professional Is likely to damage the product.
• Do not drop, intensively vibrate, or impact the product with hard object. It will damage the internal circuits.
• Do not clean the headset with harsh chemical solvents.
• Do not scratch the product surface with sharp objects. It will damage the housing and appearance.
In the event the product does not work properly, take it to an authorized service center. The staff will help you solving the problem.

FAQs

1. Red light flashes in place of blue.
Answer: It tells that your headset battery is low and need to recharge.
2. The red light does not light up during charging.
Answer: a. Make sure the charge device connects to the headset properly.
b. The battery hibernates when the headset is not used for an extended period of time. In this case, It needs about 30 minutes of charge before the red light lighting up.
3. Don’t hear anything in the headset.
Answer: a. Make sure the headset is on.
b. Make sure the headset is set to a proper volume.
c. Make sure the headset has a valid connection with the mobile.
d. Make sure the headset is within a normal working range.
4. Headset’s call quality is bad.
Answer: a. Make sure the mobile Is in a location with a strong signal.
b. The headset has an effective working range of 10m. Please make sure the headset is within working distance without obstacles between the headset and the mobile.
5. During playing. why the headset cannot perform controls over pause, resume, last song and next song?
Answer: This function requires that the device paired with your headset must support AVRCP (AudioNideo Remote Control Profile).
6. Cannot use NFC for pairing.
Answer: a. Make sure your mobile’s NFC function has been enabled.
b. When pairing at the first time, you need to keep your mobile in contact with the headset for about 3 seconds until the blue and red lights of the headset flash alternatively before taking away the mobile or a pairing may not be successful.

CAUTION
The danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type.
A warning that batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.
1. “To prevent possible hearing damage, do not listen at high volume levels for long periods.”
2. “Fully understand user manual before use.”
3. “Ensure your player at low volume levels or power off before you leaving.”

Correct Disposal of this product. This marking indicates that this product should not be disposed of with another household disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling.

Warning!
To guarantee your personal safety, please do not wear or keep earphones in the vicinity (closer than 10cm) of a pacemaker.
Do not insert plug into electric sockets. Supervise children when using the equipment, the product is not a toy.
Earphone listening at high volume levels -particularly, over extended periods of time – may damage your hearing. The operation of switches on your hi-fi system or plugging in the earphones may cause clicks which at high volume setting may affect your hearing. Therefore, always set the volume control to a minimum before switching between different sources (tuner, turntable, CD player, etc.) or plugging in the earphones. For traffic safety, do not use earphones while driving or cycling.

EDIFIER International Limited
www.edifier.com
2017 Edifier International Limited All rights reserved. Printed in china
NOTICE: For the need of technical improvement and system upgrade, the information contained herein may be subject to change from time without prior notice.
Products of EDIFIER will be customized for different applications. Pictures and illustrations shown in this manual may be slightly different from the actual product. If any difference is found, the actual product prevails.

ver.2 IB-200-w0830B-00

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>