audio-technica Automatic Wireless Turntable User Manual

Audio-Technica AT-LP60XBT Automatic Wireless Turntable User Manual

Introduction

Thank you for purchasing this Audio-Technica product.
Read through this user manual before using the product to ensure its correct use. Also, keep this manual for future reference.

This product can be used only in the countries where the product is sold. Make sure that the operating voltage and the plug of AC adapter of the product are correct for the country you live in.

Package contents

Make sure that you have all the included items listed below before using this product.
If some items are missing or damaged, contact your local Audio-Technica dealer.

After purchase, we suggest that you save all packaging materials for possible future storage, moving, or shipping.

Safety precautions

Although this product was designed to be used safely, failing to use it correctly may result in an accident. To ensure safety, observe all warnings and cautions while using the product.

Important information

Warning:
To prevent fire or shock hazard, do not expose this apparatus to rain or moisture.

Caution:

• Do not expose this apparatus to drips or splashes.
• To avoid electric shock, do not open the cabinet.
• Refer servicing to qualified personnel only.
• Do not expose this apparatus to excessive heat such as sunshine, fire or the like.
• Do not subject this apparatus to strong impact.
• This apparatus should be located close enough to the AC outlet so that you can easily grasp the AC adapter at any time.
• In case of emergency, disconnect the AC adapter quickly.
• Do not place any objects filled with liquids, such as vases, on this apparatus.
• To prevent fire, do not place any naked flame sources (such as lighted candles) on this apparatus.
• Do not install this apparatus in a confined space such as a bookcase or similar unit.
• Install this apparatus only in the place where ventilation is good.

For customers in the USA

FCC Notice

Warning:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Caution:
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Statement:
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter used in other systems. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20 cm or more away from person’s body.

For customers in Canada

IC statement:
CAN ICES-3 (B)/NMB-3(B)

This device complies with INDUSTRY CANADA R.S.S. 247. Operation is subject to the following conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference which may cause undesired operation. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.

Notes on use

Turntable body

• Do not set and use the product in locations that are considerably hot or humid, dirty, or subject to extreme vibrations.
• The product should be positioned on a flat, level surface.
• When closing the dust cover, close it completely. Do not open the dust cover during playback.
• Read the user manual for the Bluetooth receiver device.

Cartridge

• Attach the provided protector to the cartridge when the product is not in use.
• Do not touch the stylus of the cartridge with your finger.
• Do not allow the stylus to bump against the platter, felt mat, or edge of the record.

Part names and functions

1. 45 RPM adapter (shown in receptacle)
   Adapts 7″ records with large center holes to fit center spindle.

2. Platter

3. Spindle

4. Felt mat

5. Indicator LED
   Displays the Bluetooth connection status by blinking/ lighting.

6. Wireless function button
   Use to connect the product to a Bluetooth® device.

7. Dust cover hinge holders
   Attachment points for dust cover hinges.

8. Tonearm

9. Tonearm rest

10. Headshell and cartridge
    The cartridge (AT3600L) is attached to the headshell.

11. Size selector
    Switch between 12″ and 7″, according to the size of the record.

12. Dust cover

13. Platter speed button
    Select the platter speed (33-1/3 or 45 RPM).

14. START button
    Spins the platter and moves the tonearm.

15. STOP button
    Returns the tonearm to its original position and stops the platter.

16. Tonearm lift button
    Lifts and lowers tonearm for manual selection.

17. Pre-amplifier selector switch
    If using an amplifier with a PHONO input jack, set this switch to the PHONO position. If connecting to the AUX jack of an amplifier, set this switch to the LINE position.

18. Stereo output terminals
    Connect the RCA audio cable.

19. Power input jack
    Connect the AC adapter.

Preparation for use

Installing the turntable

• Mount the product on a level surface.
• To avoid the effects of vibrations and acoustic pressure, do not mount the product next to such items as speakers.
• The product may pick up radio static if placed next to a radio. Therefore, try to keep the product away from radios.
• If the product is near equipment (cell phone, etc.) that emits strong radio waves, noise may occur.

Installing/removing the dust cover

When removing the dust cover, slowly pull the dust cover out from the dust cover hinge holders. When attaching the dust cover, insert the hinges of the dust cover into the two dust cover hinge holders on the back of the body.

Assembling the product

This product requires some assembly before using it for the first time.
Do not connect the AC adapter until assembly is complete.

1. Set the platter on the spindle.

   • Make certain that the platter is fully seated on the spindle.
     

2. Place the belt on the motor pulley (brass-colored).

   • Align one of the platter openings with the brass motor pulley, and, while pulling both ends of the red ribbon that comes attached to the belt, place the belt on the motor pulley, as per the diagram. When doing this, be careful not to twist the belt.
     

3. **Remove the red ribbon from the belt.

**

4. Set the felt mat on the platter.
   • After setting the felt mat, put the 45 RPM adapter into the space made for it on the upper left.
     

Rotating the platter

1. Using your hands, rotate the platter ten times.
   • Remove the tie that locks the tonearm and press the tonearm lift button to lift the tonearm. Slowly rotate the turntable ten times by hand in the direction of the arrow.
   • You may want to hold the tonearm to prevent it from moving. This step is for resetting the auto mechanism, getting rid of any twists in the belt and making sure the belt rides smoothly along the drive rim on the underside of the platter.
     

Connecting the AC adapter

This product does not have a power switch. A standby current is always running through the product, even when it is not being used; disconnect the AC adapter from the outlet when not using the product for a long period of time.

1. Connect the AC adapter to the outlet.
   • Connect the AC adapter to the outlet without removing the cartridge’s protector. If the platter has rotated, press the STOP button without touching the tonearm, and then wait until the tonearm returns to its original position.

Wireless/wired connection

You can connect to a speaker, etc. via Bluetooth technology or RCA audio cable.
When using Bluetooth, refer to “Connecting via Bluetooth wireless technology” on p. 6.

When connecting with the RCA audio cable, refer to “Connecting the device” on p. 7.

• Volume adjustment cannot be performed if there is no volume adjustment on the connected speakers, etc.

Connecting via Bluetooth wireless technology

The product supports Bluetooth wireless connection. It can be connected with Bluetooth-compatible headphones, active speakers and wireless stereo speakers (hereinafter referred to as Bluetooth receiver devices).

About pairing

When connecting a new Bluetooth receiver device, you need to pair it with the product. Once the Bluetooth receiver device and the product are paired, you do not need to pair them again. However, in the following cases you will need to pair again even if the Bluetooth receiver device was paired once:

• If the product is deleted from the Bluetooth receiver device’s connection history.
• If the product is sent out for repair.
• If 9 or more devices are paired. (The product can save the pairing information of up to 8 devices. When you pair with a new device after pairing with 8 devices, pairing information for the device with the oldest connection date will be overwritten by the information for the new device.)

Pairing a Bluetooth device

• Read the user manual for the Bluetooth receiver device.
• Place the device within 1 m (3.3′) of the product to perform pairing correctly.

1. Set your Bluetooth headphones, speakers, etc. to pairing mode.

2. Make sure the AC adapter is connected to an outlet, and then press and hold the wireless function button (about 2 seconds).

   • The indicator LED will flash in red and blue alternately.

3. When pairing is complete, the indicator LED lights in blue.
   

• The product stays in the pairing mode for 30 seconds. If pairing is not properly completed, follow the above steps again from the beginning.

About indicator LED display

The indicator LED indicates the product’s status as explained below.

Setting pre-amplifier selector switch

This product has a built-in phono equalizer function. You can use the product even if you do not have a phono amplifier or connectable equipment with a built-in phono amplifier. Use the pre-amplifier selector switch to set the output, as shown below.

• An audio adapter (sold separately) may be required to connect the RCA audio cable to the line input jack of the PC sound card.

  • When connecting via Bluetooth, using the pre-amplifier selector switch is not necessary.

Connecting the device

Align the settings for the pre-amplifier selector switch and connect the RCA audio cable to an input jack that is compatible with the connectable equipment you are using (amplifier, receiver, active speakers, sound card, etc.).

• The RCA audio cable’s red jack is for the right (R) channel, and the white jack is for the left (L) channel.

Playing a record

Before playing a record

1. Remove the cartridge’s protector.

   • Pull the protector straight forward to remove it.
   • Applying a downward force may cause the stylus to come off the body. Only low volume is output if the stylus has come off, or is about to come off, so refer to “Replacing the stylus” on p. 10 to reattach the stylus correctly.

2. Place the record on the felt mat so that the center hole aligns with the spindle.

   • If playing a 45 RPM record with a large center hole, attach the 45 RPM adapter (see the right side of the diagram below).
     

Automatic operation

Lower the volume of the amplifier, speakers, etc. sufficiently.

1. Select the size with the size selector.

   • Select “12″” for an LP record with a 12″ diameter, and “7″” for a 45 RPM record with a 7″ diameter.

2. Press the speed with the platter speed button.

   • Select “33” for a 33-1/3 RPM record, and “45” for a 45 RPM record.

3. Press the START button.

   • Do not bump the product while the record is playing.
   • Do not switch the record size selection while the record is playing. Doing either of these can cause the product to malfunction.
     

Manual operation

Lower the volume of the amplifier, speakers, etc. sufficiently.

1. Press the tonearm lift button.

   • When you press the tonearm lift button, the tonearm rises from the tonearm rest.
     

2. **Position the tonearm over the desired location (groove) on the record.

**

3. Press the tonearm lift button.
   • When you press the tonearm lift button, the tonearm descends slowly onto the record and play begins.

Pausing the record

1. After lowering the volume of the amplifier, speakers, etc. sufficiently, press the tonearm lift button to lift the tonearm.

Stopping the record

Once the record has played to the end, the tonearm will automatically return to the tonearm rest.
To manually stop the record, do the following.

1. **Lower the volume of the amplifier, speakers, etc. sufficiently.

**

2. Press the STOP button.

   • Once the record stops playing, the tonearm automatically returns to the tonearm rest.

3. Remove the record after the platter has come to a complete stop.

• When the tonearm reaches the end (center) of the record, it will automatically lift and return to the tonearm rest. Do not interfere with its motion. Doing so can cause the product to malfunction. If the tonearm does not lift and return to the tonearm rest, press the STOP button to complete this operation.
• If the felt mat gets dirty, it can easily scratch the record, so remove the felt mat periodically and wipe off any dust.
• To prevent the record from scratches and warping, remove it after use.
• Do not use a disk stabilizer.
• Do not use a platter other than the one provided.
• This product is not intended for DJs. Do not touch the record or the platter while the record is playing.

How to use with Bluetooth connection

• To connect for the first time, pair the product and your device via Bluetooth wireless technology.
• Read the user manual for the Bluetooth receiver device.
• Note that Audio-Technica cannot guarantee the operation of displays, such as the battery level display, or applications via Bluetooth devices.

1. Turn on the Bluetooth receiver device.
   • Indicator LED turns blue when the product and Bluetooth receiver device are connected correctly.
   • When the indicator LED lights in red, press the wireless function button to connect Bluetooth communication.
2. Refer to “Automatic operation” on p. 8 or “Manual operation” on p. 8 to play a record.

• When Bluetooth is connected, and you keep the wired connection (amplifier, speaker, etc.) turned on, the sound will be heard from both the wireless and wired devices. Turn on only the device you want to use for playback.

Care

Turntable body

• When the turntable body is dirty or dusty, first disconnect the AC adapter, and then wipe off the dirt and dust with a soft, dry cloth.
• Do not use benzenes, thinners, etc.
• When storing the product for a long time, disconnect the AC adapter from the outlet and wrap the product in plastic; do not allow it to become damp.

Stylus tip

• If dirt and grime are stuck to the stylus tip, clean it with a commercially sold brush.
• We recommend using a stylus cleaner (sold separately) if the stylus tip is considerably dirty. Clean the stylus tip by moving the brush from the rear to the front of the stylus tip.

Replacing the stylus

Removing the stylus

• In addition to the deterioration of sound quality, records may also be damaged as the cartridge’s stylus tip wears down.
• As a rule of thumb, replace the stylus after 400 hours of use.
• Be sure to disconnect the product’s AC adapter from the outlet.
• When replacing the stylus, hold the headshell and the cartridge body tightly.

1. **Rotate the front of the stylus in a forward and down motion.

**

Removing the stylus

1. Mount the new replacement stylus to the cartridge.
   
   

2. **Lift the stylus up until you hear a click.

**

3. **Make sure there is no gap between the headshell and the cartridge.

**

Replacing the belt

• The belt is a consumable part. Replace the belt if the speed of playback slows down or irregular rotation occurs. As a rule of thumb, we suggest replacing the belt once a year.
• Before replacing the belt, be sure to disconnect the product’s AC adapter from the outlet.

1. Remove the felt mat.
   
   

2. Remove the platter, turn the platter over, and then remove the old belt.

   • Place your thumbs in the openings and pull up strongly.
     

3. Place the new belt around the inner circle.

   • Be careful not to twist the belt while doing this.
     

4. Attach the platter.

   • Align one of the openings with the position of the motor pulley (brass-colored).
     

5. Place the belt on the motor pulley (brass-colored).

   • Grasp the belt that was attached in step 3 and, while pulling it, place it on the brass motor pulley.
     

6. Using your hands, rotate the platter ten times.

   • Slowly rotate the turntable ten times by hand in the direction of the arrow.
     

When the turntable is moved

Using the product’s original packing materials, wrap the turntable in the reverse order from when you unwrapped it. If you do not have the packaging materials, take the following measures:

• After disconnecting the AC adapter from the outlet, remove the felt mat and platter, and then wrap them so that they do not get damaged.
• Attach the protector to the cartridge.
• Use a string or something similar to tie the tonearm to the rest so that it does not move.
• Wrap the turntable body with paper or a soft cloth so that it does not get damaged.

Troubleshooting

Dimensions

Specifications

Specifications are subject to change without notice due to improvements.

• The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc. and any use of such marks by Audio-Technica Corporation is under license. All other trademarks are property of their respective owners.
• Qualcomm aptX is a product of Qualcomm Technologies, Inc. and/or its subsidiaries. Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries, used with permission. aptX is a trademark of Qualcomm Technologies International, Ltd., registered in the United States and other countries, used with permission.

Audio-Technica Corporation
2-46-1 Nishi-naruse, Machida, Tokyo 194-8666, Japan
www.audio-technica.com
©2019 Audio-Technica Corporation
Global Support Contact: www.at-globalsupport.com

ver.1 2019.04.15
162501372-02-02 ver.2 2019.05.15

References

• Global Support｜Audio-Technica Corporation オーディオテクニカ
• Audio-Technica Corporation | Headphones, Microphones & Turntables | Audio-Technica

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>