BLAUPUNKT 12v Vehicle Lighting Led Headlamp Installation Guide

BLAUPUNKT 12v Vehicle Lighting Led Headlamp

CAUTIONS

Safety Notes
This product has been manufactured according to established safety guidelines. However, dangers may still occur if the safety notes in this manual are not observed. This manual is intended to familiarize the user with the product’s important functions. Read this carefully, prior to installing the product. Keep this manual in an easily accessible location. In addition, do observe the instructions of the devices used in conjunction with the product.

General Safety

• A headlamp is intended for installation and operation in a vehicle with 12V vehicle system voltage and can be used in headlights with H4 halogen lamps.
• Ensure the headlamp does not have defects before installation.
• Keep the headlamp away from children.
• Keep the headlamp away from flammable areas or liquids.
• The headlamp should be stored in a dry and low humidity place.
• Avoid skin contact with the high temperature/ working headlamp when replacing the headlamp. Allow the headlamp to drop to room temperature before replacing the headlight.
• Do not modify the product, or expose the product to dust, grease stains, or scratch the surface of the headlamp.
• Do not look directly at the operating headlamp, it may cause eye damage.
• After installation, ensure below are working correctly
  1. Correct light/beam pattern
  2. Indicators are working
  3. Wiring are connected correctly
  4. Covers are installed back to the car correctly
  This manual may be updated from time to time without any notice.

Disclaimer
In no event shall Blaupunkt be liable for any direct, indirect, punitive, incidental, special consequential damages to property or life and whatsoever arising out of or connected with the use or misuse of our products. USA & CANADA: This product is not intended for sale in the United States and Canada. If purchased in the U.S. or Canada, this product is purchased on an as-is basis. No warranty, whether expressed or implied is provided in the U.S. or Canada.

STRUCTURE & FUNCTIONS

Applicable to: Reflector headlight
Product Name : 134250W (5000K), 134260W (6000K)
Technology : LED
Power : 26W±10%, 26W±10%
Operating Voltage : 13.2V
Luminous Flux : 2100lm ±20%, 1900lm ±20%
Water Resistant Rating : IP65
Lifespan : 3000 hour
Colour Temperature : 5000K & 6000K
Base : P43t

Applicable to : Projector, reflector & fog headlight Product Name : 197250W (5000K), 197260W (6000K) Technology : LED
Power: 26W±10%
Operating Voltage : 13.2V
Luminous Flux : 2300lm ±20%
Water Resistant Rating : IP65
Lifespan : 3000 hour
Colour Temperature : 5000K & 6000K
Base : PX26D

Applicable to : Projector, reflector & fog headlight Product Name : 136650W (5000K), 136660W (6000K) Technology : LED
Power: 26W±10%
Operating Voltage : 13.2V
Luminous Flux : 2300lm ±20%
Water Resistant Rating : IP65
Lifespan : 3000 hour
Colour Temperature : 5000K & 6000K
Base : PGJ19-1/2/3/5

SPECIFICATIONS

Applicable to : Projector, reflector & fog headlight Product Name : 100650W (5000K), 100660W (6000K) Technology : LED
Power : 26W±10%
Operating Voltage : 13.2V
Luminous Flux : 2300lm ±20%
Water Resistant Rating : IP65
Lifespan : 3000 hour
Colour Temperature : 5000K & 6000K
Base : P22D

Applicable to : Projector & reflector headlight Product Name : 101250W (5000K), 101260W (6000K) Technology : LED
Power : 26W±10%
Operating Voltage : 13.2V
Luminous Flux : 2300lm ±20%
Water Resistant Rating : IP65
Lifespan : 3000 hour
Colour Temperature : 5000K & 6000K
Base : PX22D

TROUBLESHOOTING

If any of the following problems occur, please resort to Troubleshooting for possible solutions. Consult Blaupunkt authorized dealer if the problem persists.

PRE-INSTALLATION

1. Open the hood of the vehicle.
2. Find the installed location of the original halogen bulb.

3. Remove the halogen bulb from the headlight housing.

INSTALLATION INSTRUCTION

1. Remove the cap plate from the headlamp. 2. Insert the cap plate and secure it with the retaining spring clip.

3. Install the headlamp into headlight housing and turn clockwise to secure it.

4. Please ensure the diodes (LED chips) of the headlamp are in a side to side orientation. Correct Alignment

5. Connect the headlamp cable to the vehicle wiring harness.

• A warning canceller adaptor may be needed in case of the warning signal light up after installation.
• Remove bulb, turn it 180° & reinstall in case bulb does not light up.
• Fit for 12V vehicle only.

Attention for H4 Installation: https://www.facebook.com/blaupunkt.asia

Designed and engineered by Blaupunkt Competence Centre

134260W H4 6000K
1 581 19 014 35 01

197260W H7 6000K
1 581 19 015 35 01

136660W H8/H11/H16 6000K
1 581 19 016 35 01

100660W HB4 6000K
1 581 19 017 35 01

101260W HIR2 6000K
1 581 19 018 35 01

134250W H4 5000K
1 581 19 019 35 01

197250W H7 5000K
1 581 19 020 35 01

136650WH8/H11/H16 5000K
1 581 19 021 35 01

100650W HB4 5000K
1 581 19 022 35 01

101250W HIR2 5000K
1 581 19 023 35 01

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>