POSKER AISKITS Automotive Headlight Bulbs User Manual
- June 4, 2024
- POSKER
Table of Contents
POSKER AISKITS Automotive Headlight Bulbs
Search “Posker LED” on YouTube to find, watch our installation videos or contact our customer support Email: service@posker-us.com for help.
Dear customers:
Thank you for purchasing an Posker product. Please read this user manual
carefully and keep it for future reference. If you need any assistance, please
contact our Email: service@posker-us.com with your product model number and
Amazon order number. We will make every effort possible to ensure your
satisfaction with your purchase as well as resolve any issues you run into. In
addition, we are looking forward to your valuable opinions about our products.
Every comment will be valued by Posker.
ATTENTION
Notice
As the car becomes more and more intelligent, the automobile headlight may
alarm the product after we replacing the halogen lamp with the LED headlight .
Because of the self-detection function of this product, the power of the LED
headlight is lower than the halogen bulb, the automobile computer will
identify it as an abnormal phenomenon. If there is a dashboard prompt error,
please contact the customer service personnel. This product can be compatible
with 95% of the market models. Disclaimer
POSKER does not warranty its goods against any defect or damage caused by
transportation, storage, improper installation and maintenance, internal or
external hostile environments, misuse, abuse, negligence, accident,
modification, tampering, the attachment of any unauthorized accessory,
alteration to the goods, poor workmanship, or any other conditions whatsoever
that cause a defect or failure of the product.
POSKER ’s sole responsibility under this warranty shall be, at its option, to
either repair or replace any goods which fail during the warranty period,
provided that the buyer has promptly reported the said failure to POSKER in
writing, and complies with the provisions of this warranty.
Pre-installation Notice
- Please make sure this product has been purchased from a legal sales channel.
- This product can only be used on road-legal automotive vehicles.
- This product may contain small parts, and we strongly advise you to keep this product away from infants and children, so as to prevent a choking hazard or possible injury.
- Please test the LED bulbs before fully installing them in your vehicle.
- Before installing, please make sure the LED bulbs are not damaged or broken, and have not been dropped on the ground. If any of these conditions exist, please do not install the LED bulbs in your vehicle.
- Store this product only in a cool and dry place. Keep away from moisture and dust, otherwise it may become damaged.
- Keep the LED bulb away from areas or materials that are exposed to flames or prone to combustion.
- Please read this instruction manual carefully before installing this product. After completing the installation, please keep this manual in a safe place for future reference.
PRODUCT SPECIFICATIONS
| Operating Voltage | DC 12V |
|---|---|
| LED Chip | CSP |
| Color Temperature | 6000K |
| Material/Heat Sink | 6063 Aluminum |
| Operating Temperature | -40~80℃ |
| Waterproof Rating | IP65 |
| Lifespan | 50000 Hours |
| Warranty | 2 Year |
PRODUCT PARTS INTRODUCTION
- Locking Ring
- Heat Sink
- LED Component
- Bulb Connector
- Driver
INSTALLATION
Precautions for installation
- Please wear work gloves during the installation.
- Be sure not to touch the LED element of the LED bulb.
- Prevent any type of oil, dirt or moisture from adhering to the product, so as to prevent a potential failure.
- Bulb installation should be done safely in environments where a large amount of space is available. Before installation, stop the vehicle engine, apply the parking brake, place the shift in the park or neutral position, and remove the key.
- Be sure not to apply excessive force to the LED bulb during installation. If damage occurs, it may cause a lighting malfunction and other potential failures.
- After installation, please check whether the high and low beams and other electrical equipment on the dashboard work normally and no warnings occur.
- Please ensure the LED driver box and cable ties are not below the vehicle’s heating system or near moveable components inside the engine compartment, as this may cause damage and a potential failure.
- Please ensure that the LED driver box and cable ties do not interfere with other components or the engine hood itself.
- Do not bend the cables excessively, especially near the LED driver or heat sink area.
- Before installation, turn off the vehicle engine, stop the car in a steady place, open the hood and find the bulb installation position of the headlight assembly.
- Please start the car engine and turn on the headlight before inserting the bulb into the lamp to test whether it can be used normally. If an error occurs, please take out the bulb and contact our customer service staff.
- he strap and double – sided adhesive shipped with products are used to secure the power drive box to prevent the power box from shaking.
H11/9005/9006/9012/H13
Unscrew the dust cover (please ignore if you have no dust cover and go to the next step), remove the bulb counterclockwise, pull out the power plug, connect the plug of the LED bulb to the power connector of the automobile bulb, insert the led bulb clasp with the headlight assembly and tighten clockwise.
H4
Unplug the bulb power connector, remove the dust cover and the bulb buckle, and take out the halogen bulb. Rotate the clasp of the LED bulb, align the clasp position with the lamp assembly, load in the clasp, fasten the clasp, install the dust cover, insert the LED bulb (pay attention to the direction of the clasp installation), tighten clockwise and connect the power cord.
9004/9007
Remove the dust cover counterclockwise, unplug the bulb power connector, take out the metal buckle, the halogen bulb, and the clasp of the led bulb, fasten the metal clasp into the lamp assembly (pay attention to the direction), insert the LED lamp into the clasp, the LED elements should be facing 3 and 9 o’clock. Plug the drive box into the headlight bulb and cover the dust cover.
Note: If one of the LED bulbs does not work, it could be attributed to poor contact. Make sure the connection is good. If the problem cannot be solved, swap the left side bulb with the right side bulb and test again.
Warning:
- Do not switch on the LED bulb until the connection is finished.
- If the LED bulb flashes or warnings show up on the vehicle dashboard, please connect the resistors (CANbus) to ensure correct operation.
- If any problems still cannot be resolved under the guidance of this manual, please feel free to contact our customer support team.
Warning for use
- Do not look directly at the operating lamp for any period of time, as this may cause serious eye injury.
- Do not disassemble or modify the product in any way, as this may damage the product or cause fire and /or personal injury.
- If there is any abnormal vibration or sound when the vehicle is moving, stop immediately in a safe location and check the vehicle.
- Do not wash the vehicle with the lights turned on, as sudden changes in temperature may cause an unexpected reaction from the LED bulb.
- The LED bulb body and LED surface can reach very high temperatures. Do not touch the area with hands or allow any skin contact as it may result in severe burns.
- During heavy rain or when putting the vehicle through a car wash, condensation may build up inside the bulb compartment due to the difference in temperatures inside and outside the bulb compartment. Please note this will not affect the overall function of the LED bulb.
TROUBLESHOOTING
-
The lights do not work properly: Check if the power connectors are properly connected, and make sure that the vehicle headlight switch is in the “ON” position. Make sure that he vehicle has enough battery to supply power to the LED bulb.
Install the LED bulbs with the resistors (CANbus). -
One of the bulbs is not working: Make sure the connection is good. If one of the bulb still doesn’t work, swap the left and right side bulbs and test again. If the problem cannot be resolved, it may be caused by the vehicle’s light assembly.
-
The lights flicker or flash: Install the LED bulb with the resistors (CANbus) to resolve the issue.
-
A warning lamp appears on the vehicle’s system dashboard: This is a harmless side-effect of the low-wattage LED bulbs not being recognized by the vehicle’s system and can be resolved with the installation of an additional set of resistors (CANbus).
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>