phrozen Sonic XL 4K Plus Resin LCD 3D Printer Instruction Manual
- June 8, 2024
- phrozen
Table of Contents
phrozen Sonic XL 4K Plus Resin LCD 3D Printer
Dear User,
Thank you for joining us. Please read through the entire manual and follow the
step-by-step instructions provided to get the best printing experience.
Introduction
Printer Parts
The Toolbox
Operation
- System Phrozen OS
- Operation 5-inch Touch Panel
- Slicer Software Phrozen Dental Synergy Slicer
- Connectivity USB | Ethernet | Wi-Fi
Printing Specifications
- Technology Resin 3D Printer – LCD Type
- Light Source 405mm ParaLED® 3.0 Module
- XY Resolution 52 um
- Layer Thickness 0.01 – 0.30 mm
- Max Printing Speed Up to 90 mm / hr
- Compatible File Format PRZ
- Power Requirement AC100-240V : 50-60Hz
Hardware Specifications
- Printer Size 33 x 29 x 47 cm
- Printing Volume 20 x 12.5 x 20 cm
- Printer Weight 17.2 kg
All specifications were tested in a laboratory and are subject to change
without prior notice. For the latest update, please refer to Phrozen’s
official website.
The included power cord set packaged with the main unit cannot be used with
electrical equipment other than the specified device.
-
PRINT
Choose your 3D file to begin printing. -
Z-AXIS
Follow instructions on the manual to calibrate the Z-axis. -
LCD TEST
Please follow instructions in the user manual to conduct the LCD test. -
HEATER
To stabilize the temperature inside the printer chamber. Toggle the ON/OFF button to activate the heater function. -
LIGHT
Manually adjust the LED light settings from 50% to 100%. The default value is the best performance.
Notice: For first-time usage, please follow the user manual and conduct the following steps: Perform Z-axis Calibration, LCD Test, and Test Printing.
Key Notes Before Start
Stable Printing Environment
Store your 3D printer in a dry and ventilated environment. Avoid exposure to
direct sunlight. Make sure to place the printer on a flat surface.
Protective Measures
While printing and using resin, please make sure to wear gloves, masks,
protective goggles, and long-sleeved clothing.
Maintenance
-
Clean the Z-axis
First, dry clean the Z-axis T-screw. Then apply a thin layer of general lubricant on it, so that it whirls smoothly. -
Clean the 3D Printer
Use sanitizing alcohol and tissue paper to carefully clean the printer, the resin vat, and the building plate.
Z-axis Calibration
- Click on Z-AXIS. Then click on Z-axis Calibration.
- Remove the resin vat and place a piece of paper on the LCD screen.’
- Install the building plate and loosen all 4 screws on the building plate.
- Click on NEXT.
- The building plate will then be lowered to touch the LCD screen.
- Tighten all 4 screws on the building plate and click DONE.
- Z-axis Calibration is now complete.
LCD Test
- Click on LCD TEST.
- There are three modes to choose; from. Please test your LCD screen in the following order.
- When all three modes are clearly displayed on the LCD, LCD TEST is completed.
LCD FILL UP
Confirm the LCD screen fully lights up and there are no black spots.
BLACKENED LCD SCREEN
Confirm the LCD screen covers all the light and there are no light spots.
LCD GRID
Confirm that the LCD screen displays the grid completely.
Import 3D Files
via USB
- Plug in the USB drive into the 3D printer.
- Using the touchscreen, follow these steps: PRINT > USB icon > 3D file.PRZ > Wait for Upload.
Perform Printing Test
Test Printing
After importing your files, we can now perform the printing test.
- Install the building plate and resin vat. Make sure that both are parallel to the printer and the surface is clean.
- Shake the resin bottle for 1 minute. When pouring, make sure the resin does not exceed the mark on the resin vat.
- The building plate will go down once you initiate the printing process. After it reaches the bottom of the resin vat, the system will wait for 15 seconds before the printing begins:
- After the printing process begins, the Air Filtration System will turn on automatically.
- Keep the cover closed during printing to prevent excessive UV light.
- Tilt and place the building plate onto a desk and use a metal scraper to carefully remove your print.
After-sales service & warranty
- Phrozen offers a one-year warranty for all parts, excluding consumable components such as the LCD screen and FEP film.
- Sonic XL 4K Plus screen is covered under a 3-month warranty. Please note that this warranty does not cover any damages caused by human factors.
- If you encounter any difficulties, please scan the QR codes down below to contact us.
Congratulations!
You have just completed your first run. We hope you’ve had a great experience!
Please follow us on social media and subscribe to our YouTube Channel to learn
more printing tips, share your creations with the community.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>