COLDBUSTER HTW-1RHR Single Rail Horizontal Heated Towel Warmer Installation Guide
- June 3, 2024
- COLDBUSTER
Table of Contents
Single Rail Horizontal Heated Towel
Warmer – Round Bar
Item #: HTW-1RHR
Installation, Illustration, Cleaning &
Safety Guidelines
HTW-1RHR Single Rail Horizontal Heated Towel Warmer
Coldbuster Customer Service: 1800 85 75 65
WARNING: Failure to read this guide prior to installing your COLDBUSTER
heater(s) may result in installation problems that could void your heater
warranty.
Installation & Illustration
The layout pattern for your heated towel rails is up to, whether you choose to
install singularly or in a ladder format of 2, 3 or 4 or more heated towel
rails.
Whichever layout pattern you choose, please be sure to discuss with your
Builder, Tiler, Electrician and Trades Person as pre-planning and prep work
will be required by all.
Step 1: Choose the layout best suited for your bathroom design. It would be
beneficial to consult with your Builder, Tiler, Electrician or Trades Person
to ensure the location you desire can be accommodated with electrical
services and installation requirements.
Step 2: Arrange for your electrician to run conduit or appropriate wiring to
the wall area and the location of your heated towel rails. This should be
completed before any tile work or gyprock, or wall material goes up as you
will need to ensure access to the conduit and location. If tiling is already
completed, you will need to arrange with your Electrician the best location
for installation and power access.
Step 3: Tiling can be completed for the wall area, however the conduit and
location for the wire connection should be marked and recorded.
Step 4: Mark mounting holes (6mm) and electrical cable access hole (8mm) on
the tiles according to the dimensions of your heated towel rails, ensuring you
have identified where mains electrical supply is located in the wall at
mounting points.
Appropriate Fixing Base can be mounted on left side or right side, depending
on location of electrical cable connection. (Fig 1) Step 5: Feed electrical
cable coming from the rail, through the hole in the fix bases and then
through hole in the wall. Please note towel rail has electrical cable at one
end only. It can be mounted with cable on the left side or the right side.
Step 6: Mount the 2x fix bases into the wall by first inserting the plastic
expander (6mm) and then screwing the ST545 mounting screws into place. (Fig
2)
Step 7: Slide the ends of the rails over the fix bases and tighten the M56
mounting screws on the underside with allen key. (Fig 2) 
Connection and On/Off Management
Option 1:
Heated towel warmers are not thermostatically controlled and do not require
a thermostat. However heated towel rails can be operated by a Dual Thermostat
that is managing underfloor heating. 1 part of the Dual thermostat will
manage underfloor heating, using a floor sensor to sense actual floor
temperature and can be managed by the thermostat (time and temperature).
Temperature for floor heating will be controlled by the thermostat. Coldbuster
now have the Coldbuster Dual Thermostat designed specifically for this type
of application.
The 2nd part of the Dual Thermostat will operate as an on/off timer where the
heated towel warmers can be connected. A timer will turn heated towel warmers
on and off as programmed, however temperature is pre-set and not adjustable
for the heated towel warmers.
This will require pre-planning with your Electrician or Builder to ensure
mains power can be run to the required thermostat point as well as conduit
and/or wiring cable. Wiring and cable will also need to be in place from the
installed location of your heated towel rails to the thermostat location. (Fig
4.)
Option 2:
Heated towel warmers can be connected to a timer. Meaning towel warmer will
start heating at the programmed time, turning off at the programmed time.
Timer can be located on the wall next to a light switch or any convenient
place that is accessible. This will require pre-planning with your Electrician
or Builder to ensure mains power can be run to the required installation
point of your heated towel rails as well as conduit and/or wiring cable is in
place to the timer location. Coldbuster do not offer a plain Timer, however
your Electrician will be able to source and supply an appropriate Timer. (Fig
4.)
Option 3:
Heated towel rails can be connected to a dedicated standard light switch.
Meaning towel rails will start heating when switch is turned on and stop
heating when switch is turned off. Light switch can be located in a
convenient location within the room. This will require pre-planning with your
Electrician or Builder to ensure mains power can be run to the required light
switch location. Conduit and/or wiring cable will also need to be in place
from the heated towel rail location to the light switch location. Coldbuster
do not offer a standard light switch, however your Electrician will be able to
source and supply an appropriate light switch. (Fig 4.)
Multiple Heated Towel Rails
If 2 or more heated towel rails are to be installed in a ladder format, heated
towel rails should be wired in parallel. Please consult with your Electrician.
Cleaning
As heated towel rails will require a wipe down from time to time, use only a
soft damp cloth.
A mild detergent may be used if dirt and spots need to be removed. Gently wipe
and rinse with soft damp cloth after use.
You can dry using a microfiber cloth to dry and polish heating tubes and base
flanges.
NOTE: Do not use abrasive or corrosive cleaners on stainless heated towel
rails at any time.
Safety Information
Please follow the basic safety instructions when using the electric heated
towel rail products.
READ THESE INSTRUCTIONS CAREFULLY. Keep them handy for future reference.
- This appliance is used for warming and drying towels; therefore, it is hot to touch. Young children or infirm persons should be supervised when the product is working and ensure that they do not touch the appliance.
- The appliance will feel hotter to touch during warmer periods because of the rise in ambient temperature. Also, the insulation effect of towels will cause the operating temperature to increase slightly.
- The appliance should be installed so that switches and other controls cannot be touched by a person in the bath or shower.
- This appliance is ONLY used for warming and drying towels, DO NOT use it for any other purpose.
- To avoid danger this product MUST NOT be used to carry towels or any other articles that have been in contact with oil, petroleum-based products, or dry-cleaning fluids.
- Make sure the voltage complies with the specification on the rating label, or elsewhere in these instructions.
- DO NOT immerse in any liquid.
- DO NOT allow the power cord to come in contact with the hot surface of the heating tubes when it is working.
- If the product does not work well or is damaged, it must be fixed or replaced by the manufacturer, its service agent, or similarly qualified persons.
- WARNING: The bottom rail of this product MUST be installed at least 600mm above the floor in order to avoid risk of harm to young children.
- *NOTE: Any electrical work must be conducted by a qualified licenced electrician.
Where Can Heated Towel Rails Be Installed?
| Zone | requirements |
|---|---|
| Zone 0 | Inside the bath or shower. Any Lighting used here must have a minimum |
rating of IP67 (protected against immersion in water)
Zone 1| Above the bath or shower to a height of 2.25m. A minimum rating of
IP44 is required
Zone 2| The area stretching to 0.6m outside the bath or shower and above the
bath or shower if over 2.25m. An IP rating of at least IP44 is required
Outside Zone| Anywhere outside zones 0, 1 & 2. Where water jets are not to be
used for cleaning purposes, the general rules of BS7671 apply
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>