Disney 22GM26232 Life-Size Animated Oogie Boogie Character Instruction Manual
- October 30, 2023
- DiSNEY
Table of Contents
Disney 22GM26232 Life-Size Animated Oogie Boogie Character
Thank you for purchasing the Life-Size Animated Oogie Boogie character! Below you’ll find assembly instructions and other information to get maximum enjoyment from your purchase! Please keep these instructions for future reference because they contain important information.
PACKAGE CONTENTS
- A. Base – 1PC
- B. Support poles – 2PCS
- C. Costume – 1PC
- D. Hip – 2PCS
- E. Torso frame – 1PC
- F. Right arm – 1PC
- G. Left arm – 1PC
- H. Head – 1PC
- I. Try me button – 1PC
- J. Adapter – 1PC
PREPARATION
- Estimated Installation Time: 15 – 20 minutes.
Before beginning installation of product, make sure all parts are present. Compare parts with package contents list. If any part is missing or damaged, do not attempt to assemble, install or operate the product.
ASSEMBLY INSTRUCTIONS
- Attach support poles (B) to the base (A) as shown and secure by aligning the quick-connected push button into the predrilled holes. Lower the costume (C) over the support poles.
- Lower the hip (D) into the hole on the torso frame (E). Attach the torso frame (E) as shown and secure by aligning the quick connected push button into the pre-drilled holes.
- Connect the right arm (F) up through the right sleeve and slide the forked hooked into hole on the torso frame. Repeat for the left arm (G). Carefully connect wired jack from the function box to the arms and base. Set the head (H) onto the torso frame into the hole. Carefully connect wired jack from the function box to the head.
- Connect the UL adapter and TRY ME button through the costume and out the back.
FIGURE FUNCTIONALITY
The Life-Size Animated Oogie Boogie figure has 3 operation settings which can be changed at the main function control box on the torso frame:
- TRY ME: Push-button activation
- OFF: No function
- SENSOR: Switch to “SENSOR” position and make a noise or walk by to activate. Please remove the insulating strip before use.
STORAGE
Do not discard box as it should be used for storage. Return all parts to the original packaging. Store in a cool, dry location.
SAFETY WARNING
Remove all plastic fasteners and tags. These are part of the packaging and should be discarded. For indoor use only. This item is not a toy and should be used for decorative purposes only.
WARNING
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the distance between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
THESE INSTRUCTIONS APPLY TO THE FOLLOWING ITEM NUMBER
Visit WWW.GEMMY.COM for more information.
©2022 GEMMY INDUSTRIES CORP.
117 WRANGLER DRIVE, SUITE 100
COPPELL, TX 75019 U.S.A.
1 (877) 250-9032
MADE IN CHINA / PRINTED IN CHINA