dams Elev82 Mono – Back-to-Back Desks Instructions
- June 7, 2024
- dams
Table of Contents
dams Elev82 Mono – Back-to-Back Desks
ASSEMBLY INSTRUCTIONS
Warning: Please check that you have all the components. 
ELEV82 MONO BACK-TO-BACK DESKS ASSEMBLY
Step 1
Unpack your new height adjustable desk frame and place on a flat surface.
Step 2
Insert the desktop end rails into the frame cross sections.
Step 3
Insert the right leg into the frame and use 4 of the bolts supplied to fix into place.
Step 4
Insert the left leg at a 45° angle before fixing the leg in its upright position with the other 4 bolts provided.
Step 5
Extend the frame to the required length. Once at the desired length tighten the grub screws on the frame.
Step 6
Before connecting the legs to the motor ensure that they are at their lowest point. This will mean that the desk is level when rotated to its upright position.
Step 7
It is now time to attach both of the legs to the motor. Follow the steps shown
to secure the shaft from the motor to the bayonet fixing on each leg.
Step 8
Repeat the steps 2 through 7 for both desk frames. There are two holes in each leg of the frames, make sure these are pointing inwards in order to join the desks together.
Step 9
Insert one of the supplied bolts into the bottom hole on the leg frame as
shown. This will be to attach the cross beam.
NOTE: You should be able to still see some of the thread of the bolt. If
the thread is not visible, loosen the bolt by a few turns to leave a
gap.
Step 10
Insert the cross beam over the bolt and raise it into the keyhole
position.
Step 11
Once in position, a second bolt will be able to be inserted and both bolts to be tightened as necessary.
Step 12
Once the cross beams are attached, turn the desk over into its upright
position. 2 person lift, do not attempt to do this without assistance, this
could result in injury or damage to the product.
Step 13
Now position the desktop onto the framework ensuring that the scalloped edge
of the desktop is at the centre of the frame. Align the holes in the desktop
end rails with the pre-drilled holes on the underside of the desktop. Use the
wood screws supplied to attach the top to the frame, if you are using a
cordless/power driver make sure it is on a low torque setting.
NOTE:
Use Ø5 x 20mm wood screws to attach the top to the frame.
Step 14
Finally attach the desktop controller to the underside of the desktop using
the wood screws provided. If you are using a cordless/power driver make sure
it is on a low torque setting. There are pre-drilled holes on either side of
the top so the controller can be attached to the Left or Right of the
desk.
NOTE: Use Ø4 x 25mm wood screws to attach the controller to the top.
Step 15
Your desk is now ready to be connected to the mains outlet. Before you proceed with operating your new desk it is recommended that you perform a full reset of the controller to calibrate the height of each leg. This can be done using the following steps;
- Press button down for 3 seconds.
- Continue pressing the button until both columns are in lowest position.
- Keep pressing the button until control box makes 1 beep.
- When control box makes 1 beep, it is confirmed that reset has been completed and button can be released.
- Now the desk is operational.
- If the desk is disconnected by accidently pulling out the plugs at the control box, motors, handset, main power source or system status reach overload, overheat etc. then the desk must be reset.
- If the desk is powered off intentionally at the main power switch, then the desk does not need to be reset.
Operating the desk
Press the button, to operate the desk for upwards running.
Press the button, to operate the desk for downwards
running.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>