NEXA LED 12-24v Dimmer Module User Manual
- June 7, 2024
- NEXA
Table of Contents
NEXA LED 12-24v Dimmer Module
Dimmer receiver for permanent installation with adjustable minimum brightness. Suitable for dimmable LED strip and LED luminaires with a built-in 12-24 V driver
SAFETY
Read through all of the instructions first. Call in a professional if
necessary. Nexa cannot be held liable if the product is used for any purpose
other than the one for which it is designed, or if there is failure to comply
with the instructions. Never connect bulbs or equipment exceeding the
receiver’s maximum stated load – this could lead to faults, short-circuiting
or fire. Do not attempt to repair the product. The product contains no
repairable parts.
INSTALLATION
Connect the positive conductor from the voltage source (AC/DC adapter) to + and the negative conductor to – on DC in, the load’s positive conductor + and negative conductor to – on DC out on the LDR-075. See also wiring diagram.
LINKING
- Power up the LDR-075
- Press the learn button, the LED indicator will start to flash
- Press the “ON” button for the selected channel on a System Nexa transmitter within 15 seconds.
LINKING CONFIRMATION
The LED indicator lights steadily, if there is a bulb connected to the
receiver it will flash twice.
DELETING A MEMORY SLOT
- Press the learn button
- Press the “OFF” button for the selected channel on a System Nexa transmitter within 15 seconds.
DELETION CONFIRMATION
The LED indicator lights steadily, if there is a bulb connected to the
receiver it will flash twice.
DELETING ALL MEMORY SLOTS.
- Press and hold down the learn button for 6 seconds, the LED indicator starts to flash rapidly.
- Release the learn button and then briefly press it again.
CONFIRMATION OF THE DELETION OF ALL MEMORY SLOTS
The LED indicator lights steadily, if there is a bulb connected to the
receiver it will flash twice.
MEMORY
The LDR-075 has 6 memory slots which means that it can be controlled by up to
six transmitters at the same time.
DIMMER SETTINGS
There are a total of four levels for lowest dimmer level where 4 is the
lightest and 1 the darkest. The receiver is supplied set to the highest level
(4).
SET THE LOWEST DIMMER LEVEL
- Light the connected lamp using the transmitter
- Press the training button twice. The LED indicator starts to flash and the connected lamp dims to the lowest level currently set
- Press the “OFF” button for the selected channel on the transmitter to lower the level one step and “ON” to raise the level one step
- Press the training button twice to confirm the selected dimmer level
If the connected bulb starts to flicker or goes out completely, go back one step in the lowest dimmer level settings.
SETTING THE LOWEST DIMMER LEVEL CONFIRMATION
The LED indicator lights steadily, if there is a bulb connected to the
receiver it will flash twice.
CONTROL
The receiver can be controlled in a number of ways.
- Using a trained System Nexa remote control
- Using other trained System Nexa transmitters
- Using a Nexa Bridge
OTHER INFORMATION
Range indoors: up to 30 m (optimal conditions). The range is very dependent on
local conditions, if there is metal in the vicinity for example. The thin
metal coating in low emissivity energy glass has a negative effect on the
range of radio signals for example. There may be restrictions on the use of
the unit outside the EU. If appropriate, you should check that the unit
complies with local regulations.
Max. load: Never connect bulbs or equipment that exceed the maximum load
of the receiver. This could lead to faults, short-circuiting or fire.
Life-support equipment: Never use Nexa’s products for life-support
equipment or other devices where faults or interference could have life-
threatening consequences.
Interference: All wireless units can suffer from interference that can
affect performance and range. Because of this, the minimum distance between
two receivers should be at least 50 cm .
Repair: Do not attempt to repair the product. It does not contain any
repairable parts.
Water tightness: The product is not waterproof. Make sure it remains dry
at all times. Damp will cause the internal electronics to corrode and this
could lead to short-circuiting, faults and a risk of electric shock.
Cleaning: Clean the product using a dry cloth. Do not use chemicals,
solvents or strong cleaning agents.
Environment: Do not expose the product to intense heat or cold as this
could damage or shorten the service life of the electric circuits.
WIRING DIAGRAM
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>