NEXA Plug-in Dimmer MYCR-100 User Manual

June 6, 2024
NEXA

NEXA Plug-in Dimmer MYCR-100

TECHNICAL DATA

MYCR-100|
---|---
MYCR-100| 220–240 V~50 Hz
Max. load| 20 W
Max. load LED| 3–25 W LED
Frequency| System Nexa (433.92 MHz)
Range| up to 30 m
Memory slots| 32
Own consumption| < 1 W
Built-in protective device| Temperature fuse
IP classification| IP20 Indoor use
Dimensions, Ø| 48 mm
THIS PRODUCT FEATURES SUPPORT FOR SMART MODE.
In units that support Smart Mode, up to 3 different favourite scenarios can be saved and then activated easily using a Nexa Smart Mode transmitter.

Plug-in receiver with dimmer function for earthed sockets. Works with System Nexa remote controls, transmitters and Nexa Bridge. The system is “self- learning”, which ensures extremely simple and flexible installation.

INSTALLATION

Connect power to the receiver; make sure that the output does not exceed the output stated in the table under “Technical Data”.

PROGRAMMING

  1. Connect the receiver (plug-in) to an electrical socket. The receivermwill switch to programming mode as soon as current is applied.
  2. Press the “ON” button for the chosen channel on any SystemmNexa remote control within 6 seconds.

CONFIRMATION OF PROGRAMMING

The connected light will dim up and down two times.

DELETE MEMORY

  1. To delete a memory slot, remove the receiver (plug-in) from the wall socket.
  2. Wait for at least 6 seconds.
  3. Replace the receiver in a wall socket.
  4. Press the “OFF” button for the selected channel on a System

Nexa remote control within 6 seconds.
To delete all memory slots, repeat steps 1­3 above and then press the “ALL OFF” button on the System Nexa remote control within 6 seconds.

CONFIRMATION OF DELETION

The connected light will dim up and down two times.

MEMORY

Each MYCR-100 plug-in receiver has 32 memory slots. When all 32 slots are full, slot 1 will be overwritten on new programming.

CONTROL

The plug-in receive can be controlled in several ways.

  1. With a System Nexa Remote Control
  2. With other programmed System Nexa transmitters
  3. With Nexa Bridge

DIMMER SETTINGS

The MYCR-100 is supplied set up for trailing edge phase dimming.

SETTING THE LOWEST DIMMER LEVEL

  1. Remove the (plug-in) receiver from the wall socket.
  2. Wait for at least 6 seconds.
  3. Replace the receiver in a wall socket.
  4. Press the ON button on a programmed System Nexa remote control for 3 seconds within 6 seconds.
  5. The connected light will dim up and down two times. 6. Use the programmed remote control to adjust the lowest dimmer level. ON increases the level one step, OFF reduces the level one step. (Four steps in all)
  6. Press the ON button on a programmed System Nexa remote control for 3 seconds to confirm the lowest dimmer level.
  7. The connected light will dim up and down two times, and then dim down to the lowest level set to confirm the new setting.

Safety and information

Range indoors: up to 30 m (optimal conditions). The range is heavily dependent on local conditions ­ such as if there are any metals nearby. For example, the heavy metal coating in lowemission energy glass has a negative impact on the range of the radio signals. There may be limitations on the use of the unit outside the EU. If appropriate, check that the unit complies with the local regulations.
Max. load: Never connect lights or equipment that exceeds the maximum load of the receiver. This can result in faults, short circuit or fire.
Life-support equipment : Never use Nexa products for life support equipment or other devices where faults or disruptions can have life- threatening consequences.
Disruptions: All wireless units can be affected by disruptions that may have an impact on performance and range. The minimum distance between two receivers should therefore be at least 50 cm.
Repairs: Do not attempt to repair the product. It does not contain any serviceable parts.
Waterproofing: The product is not waterproof. Make sure that it is always dry. Moisture will corrode the electronic components inside and may result in short circuit, faults and risk of electric shock.
Cleaning: Clean the product with a dry cloth. Do not use chemicals, solvents or potent cleaning agents.
Environment: Do not expose the product to extreme heat or cold, as this may damage the electronic circuits or shorten their service life.

EXA AB, DATAVÄGEN 37B, 436 32 ASKIM, SWEDEN
info@nexa.se | www.nexa.se

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals