NEXA MYC-4 3 Plug In and Remote Control Instruction Manual

October 30, 2023
NEXA

NEXA MYC-4 3 Plug In and Remote Control A0

MYC-4

3 PLUG-IN & REMOTE CONTROL
TECHNICAL INFO
MYCR-2300, REMOTE SWITCH
Switch type Relay
Suitable loads  Incandescent & Halogen lights, max. 2.300W

Resistive & Inductive loads, max. 2.300W
Electronic transformers, max. 230 VA
Power supply| 220-240 VAC
Max load| 2.300W / 10A Resistive load
Standby power consumption| < 0.5 W
Memory slots| 32
Protocol| System Nexa
Range| up to 30 m
Ambient temperature| 0 – 35°C
Pollution degree| 2
Built in protective device| Temperature fuse

MPET-2120, REMOTE CONTROL
Power supply 3V – CR2032 Battery
Protocol System Nexa
Max ERP < 10 mW

Declaration of conformity is available at www.nexa.se

MYCR-2300 is a relay receiver (on/off) for earthed sockets.

INSTALLATION: Connect the charge to the receiver. Ensure that the charge does not exceed 2300 W.

LEARNING: Insert the receiver (plug-in) in the socket. The receiver goes into learning mode as soon as it is powered up. Press on optional channel (1, 2 or 3) on the remote control within 6 seconds.

CONFIRMATION LEARNING: Two click sounds from the receiver. If a light is connected, it flashes two times.

DELETING MEMORY: To delete a storage location, take the receiver (plug- in) out of the socket. Wait for at least 6 seconds. Insert the receiver in the socket. Double click on selected channel on the remote control within 6 seconds.

To delete the entire memory, take the receiver out of the socket. Wait for at least 6 seconds. Insert the receiver in the socket. Double click on the G button (Group) on the remote control within 6 seconds. The receiver (plug-in) confirms with two click sounds.

MEMORY: Each receiver (plug-in) has 32 storage locations. When storage location 32 is occupied, location 1 is written over.

QUICK GUIDE

Plug the receiver into the socket

Click on the remote control within 6 sec.

NEXA MYC-4 3 Plug In and Remote Control A3

  1. ON  1  x CLICK
    OFF 2 x CLICK

  2. Battery

  3. Remove

Safety instructions and information

Range indoors: up to 30 m (optimal conditions). The range is very dependent on the local conditions, for example, if there are metals in the vicinity. For example, the thin metal coating in energy glass with low emissivity has a negative influence on the range of the radio signals. There may be restrictions on the use of the unit outside the EU. If appropriate, you should check that the unit complies with local regulations.

Max load: Never connect lights or equipment that exceed the receiver’s maximum load. This could lead to faults, short-circuiting or fire.

Life-support equipment: Never use Nexa’s products for life-support equipment or other devices where faults or interference could have life- threatening consequences.

Interference: All wireless units can suffer from interference that can affect the performance and range. For this reason, the minimum distance between two receivers should be at least 50 cm

Repair: Do not attempt to repair the product. It does not contain any repairable parts.

Waterproofing: The product is not waterproof. Make sure it is dry at all times. Damp causes the electronics inside to corrode and this could lead to shortcircuiting, faults and a risk for electric shocks.

Cleaning: Clean the product with a dry cloth. Do not use chemicals, solvents or strong cleaning agents.

Environment: Do not expose the product to intense heat or cold, because it could damage or shorten the service life of the electric circuits.

NEXA AB, DATAVÄGEN 37B, 436 32 ASKIM, SWEDEN
info@nexa.se | www.nexa.se

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals