vtech 2-Line Answering System with Dual Caller User Guide

June 7, 2024
vtech

logo

Quick start guide
DS6151/DS6151-11/DS6151-2

Install the telephone base
Follow the figures below to install the telephone base as shown below:
Figure One: Installation with 2-line jackInstallation with 2-line
jack-

Figure Two: Installation with separate line jacks

Installation with 2-line jack- Figure Two Installation with separate line
jacks

NOTE: Use only the power adapter and battery supplied with this VTech telephone. For complete feature instructions, please refer to your user’s manual.

Battery installation and charging

Install the battery as shown below. After installing the battery, you might be able to make and receive short calls. For best performance, charge the handset battery for at least 16 hours before use.

1. If the battery compartment cover is on the handset, press the indentation and slide the cover to remove it.
Installation with 2-line jack- If the battery
2. Plug the battery connector securely into the socket inside the handset battery compartment, matching the color-coded label.
Installation with 2-line jack- If the batter3. Place the battery with the label THIS SIDE UP facing up and the wires inside the battery compartment.
Installation with 2-line jack-Place the battery with
4. Align the cover flat against the battery compartment, then slide it towards the center of the handset until it clicks into place.
Installation with 2-line jack-Align the cover flat5. Charge the handset by placing it in the telephone base or charger. The CHARGE light is on when the handset charges.

Make, answer and end a call Using the handset:
Make a call
Installation with 2-line jack-answer and end a call 1. Press , or
2. Enter the telephone number.
Predial a call
1. Enter the telephone number.
2. Press , or
Answer a call
Press or to answer.

End a call
Press OFF or return the handset to the telephone base to hang up.
Using the telephone base:
Make a call
1. Press LINE 1 or LINE 2.
2. Enter the telephone number.
Predial a call
1. Enter the telephone number.
2. Press LINE 1 or LINE 2.
Answer a call
Press LINE 1 or LINE 2 to answer.
End a call
Press LINE 1 or LINE 2.

Turn the answering system on or off
You must turn on the answering system for answering and recording messages.
To turn on or off with the telephone base:
Installation with 2-line jack-answer and end a

  1. Press /ON/OFF LINE 1 and/or /ON/OFF LINE 2 to turn on the corresponding answering system. The telephone base announces and shows, “Calls will be answered.” The /ON/OFF LINE 1 light and/or / ON/OFF LINE 2 light will be on respectively.
  2. Press /ON/OFF LINE 1 and/or /ON/OFF LINE 2 to turn off the corresponding answering system. The telephone base announces and shows, “Calls will not be  answered.” The /ON/OFF LINE 1 light and/or /ON/OFF LINE 2 light will be off respectively.

To turn on or off with a handset:

  1. Press the MENU softkey when the handset is not in use.
  2. Press the SELECT softkey to select ANSWERING SYS.
  3. Press ▲ or ▼to select Mailbox 1 or Mailbox 2 , then press the SELECT softkey. The corresponding icon, ****1 or 2, flashes on the screen.
  4. Press ▲ or ▼ to select Ans sys setup , then press the SELECT softkey.
  5. Press ▲ or ▼ to select Answer ON/OFF, then press the SELECT softkey.
  6. Press ▲ or ▼ to select On or Off, then press the SET softkey to confirm your setting, or press the BACK softkey to exit to the previous menu without making any changes.
  7. The screen displays or when the AnS1 ON AnS ON2 answering system of line 1 or line 2 is turned on respectively. The screen displays when the answering systems of both lines 1 and 2 are turned on. AnS1 ON. or when the answering system of line 1 or line 2 is turned on respectively. The screen displays
    when the answering systems of both lines 1 and 2 are turned on.

Outgoing announcement

The telephone is preset with a greeting that answers calls with “Hello, please leave a message after the tone.” You may use this preset announcement, or replace it with your own. Use the telephone base to record your own announcement:

  1. Press •/REC while the telephone base is not in use.
  2. Press▼CID or▼ /DIR to select
  3. Press ▼/CID or ▲/DIR to select Mailbox 1 or Mailbox 2, then press the SELECT softkey. The corresponding icon, 1 or 2, 2  lashes on the screen.
  4. The telephone base announces, “Record after the tone. Press 5 when you are done.” After the tone, speak towards MIC (microphone) of the telephone base. Press 5 or the STOP softkey when finished recording.
  5. The answering system automatically plays back the newly recorded announcement. Press 5 to stop the playback at any time.

Use a handset to record your own announcement:

  1. Press the MENU softkey menu when the handset is not in use.

  2. Press the SELECT softkey to select ANSWERING SYS.

  3. Press ▲ or ▼to select Mailbox 1 or
    Mailbox 2, then press the SELECT softkey corresponding icon, 11or 2, flashes on the screen.

  4. Press▲ or▼ to select Ans sys setup, then press the SELECT softkey.

  5. Press ▲ or▼ to select Announcement, then press the SELECT softkey.

  6. The handset announces, “To play, press 2. To record, press 7.” Press 7 to record and the screen shows Recording announcement…, or press the BACK softkey to exit to the previous menu.

  7. The handset announces, “Record after the tone. Press 5 when you are done.” After the tone, speak towards the microphone of the handset.

  8. Press 5 or the STOP soft key when finished recording.

  9. The answering system automatically plays back the newly recorded announcement. Press 5 to stop the playback at any time; 2 to replay the recorded announcement, or 7 to record again if desired.

  10. Press the BACK softkey to exit to the previous menu.

To play messages with the telephone base:

Press /MAILBOX LINE 1 for line 1 or ./MAILBOX LINE 2 for line 2 to listen to messages.
Options during playback:

  • Press ▼ /VOL/▲ to adjust the speaker volume.
  • Press /SKIP to skip to the next message.
  • Press /REPEAT to repeat the message currently playing. Press /REPEAT twice to listen to the previous message.
  • Press Χ/DELETE to delete the current message. The system advances to the next message.
  • Press /MAILBOX LINE 1 for line 1 or /MAILBOX LINE 2 for line 2 to stop listening to messages.
  • Press CANCEL to exit to the previous menu.

To play messages with a handset:

  1. Press the MENU softkey when the handset is not in use.
  2. Press the SELECT softkey to select ANSWERING SYS.
  3. Press or to select Mailbox 1 or Mailbox 2. Press the SELECT softkey.
  4. Press or to select Play messages, then press the SELECT softkey.

Options during playback:

  • Press ▼/VOL/▲ to adjust the speaker volume.
  • Press 6 to skip to the next message.
  • Press 4 to repeat the message currently playing. Press 4 twice to listen to the previous message.
  • Press 3 to delete the current message.
  • The system advances to the next message.
  • Press 5 to stop.
  • Press the BACK softkey to exit to the previous menu.

IMPORTANT!
If your product is not working properly:
Refer to the Troubleshooting section of the user’s manual.
Visit our website at www.vtechphones.com or call 1 800-595-9511. In Canada, go to www.vtechcananda.com or dial 1 800-267-7377.

Disclaimer and Limitation of Liability

VTech Communications, Inc. and its suppliers assume no responsibility for any damage or loss resulting from the use of this user’s manual. VTech Communications, Inc. and its suppliers assume no responsibility for any loss or claims by third parties that may arise through the use of this product.
Company: VTech Communications, Inc.
Address: 9020  SW Washington Square Road
– Ste 555 Tigard, OR 97223, United States
Phone: 1 800-595-9511 in the
U.S. or 1 800-267-7377 in Canada

Specifications are subject to change without notice.
© 2020 VTech Communications Inc.
All rights reserved. 06/20. DS6151_QSG_V4.0
Document order number: 96-007197-040-100

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals