godox LED Video Light Instruction Manual

: June 7, 2024
: Godox

Table of Contents

Body
- Main Body
LCD Panel
- Main Body
- Included Items
Power Supply
Operation
Wireless Control
Technical Data
FCC Warning
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

godox LED Video Light

Body

Main Body

LCD Panel

Main Body

Included Items

LED video light
Controller
Adapter
Power cord
Connect cord
Remote control
Reflector for Bowens mount LED light
Lamp cover
Portable bag
Instruction manual

Power Supply

Firstly, plug the two ends of connect cord separately into the controller’s output control port and the light’s power input socket. A “click” will be heard once finished.
Plug the output end of adapter’s connect cord into controller’s power input end.
Use the power cord to connect the power supply.

Note: If using V-port battery, please insert the battery into the LED light and power it on for usage.

Operation

Power on/off: long press the Power Switch of controller to power the LED light on or off.
Choose group/channel: press GR/CH button for once, and turn the Select Dial for Light Brightness to change the channel value. Then, press GR/CH button again, and turn the Select Dial for Light Brightness to change the group value (the group figure will be displayed recurrently). Press GR/CH button to exit.
Light brightness adjustment: turn the select dial for light brightness to change the value from 0% to 100%.
Power option: press the GR/CH button and power the light on to enter power option mode. Turn the brightness select dial to choose power from 300, 250 and 200. The power is 300W by default. Exit from this mode automatically without operation for 5 seconds.

Note: This function is used for the situation that the battery enters to protection states and cannot word due to some v-port battery doesn’t output the corresponding power in strong power output. When enter this mode, the output power of the light can be decreased and the battery can be loaded instead of being protected (this function only applies to VL300).

Wireless Control

(433MHz wireless & smartphone APP through Bluetooth)

1. With 433 MHz wireless system, VL series have remote grouping and control function. Up to 6 groups of LED lights can be controlled. 16 channels are available with strong ant interference capability. Please set the channels and groups of LED light to the same as those of RC-A5II remote control before usage.

Adjusting Channel/Group of the Controller

Press the GR/CH button and the channel icon blinks. Turn the select dial for light brightness to choose a channel ID (1 to 16).
Press the GR/CH button twice and the group icon blinks. Turn the select dial for light brightness or color temperature to choose a group ID (A to F).

Adjusting Channel/Group of the Remote Control

Press the CH/GRP button and the group icon blinks. Press the “-” or “+” button to choose a group ID (A to F).
Press the CH/GRP button twice and the channel icon blinks. Press the “-” or “+” button to choose a channel ID (1 to 16).

Adjusting Light Brightness with the Remote Control

Press the “-” or “+” button to adjust the light brightness

Note: The wireless signal can be received only when the controller is power on.

2. Godox VL series LED lights can also be controlled by smartphone APP through Bluetooth with 6 groups and 16 channel.

Bluetooth connection: power the LED light on and long press the GR/CH button until a Bluetooth ID is displayed on the controller. Then, open the “GodoxPhoto” APP, click the Bluetooth and choose the corresponding Bluetooth ID of the controller. Finally, enter the password (the initial password is “000000”), and the Bluetooth is successfully connected.
Note: The channels and groups of LED controller and APP should be adjusted to the same.
LED control: please find more details in the “GodoxPhoto” APP of smartphone: Setting—Help—LED.

Technical Data

VL Series LED Light	Vl150	Vl200	Vl300
Power Supply	DC Power

supply

| AC100V-240V(50/60HZ) /2A(DC16.8V 10A)| AC100V-240V(50/60HZ) /3.9A(DC33V 7A)| AC100V-240V(50/60HZ)

/4.3A(DC33V 10A)

Reflector

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

*RF warning:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.