SOUNDPEATS TrueDot Earbuds User Manual

SOUNDPEATS TrueDot Earbuds User Manual

Package Content

Specifications

Button Controls

Press and hold the MFB for 1.5s in off status
Power Off| Place back the earbuds into the charging case
Hold and Press the MFB for 8s
Play/Pause| Double tap the MFB of Right earphone
Play Next| Hold and press the MFB of Right earphone for 2s
Play Previous| Hold and press the MFB of LeN earphone for 2s
Answer/Hang Up Phone Call| Double tap the MFB of Right earphone
Reject Phone Call| Hold and press the MFB of Right earphone for 2s
Call Switching| Hold and press the MFB of Right earphone for 2s
Activate Voice Assistant| Double tap the MFB of LeN earphone

Wearing

1. Identify the left and right earbuds.
2. Insert the earbuds into your ears and adjust to find best angle with microphone downwards.
3. Make sure the eartips seal the ear canals.

Getting Started

1. Take out both earbuds from the charging case, the two earbuds will flash in white at first. Then the left indicator goes out, and right indicator flashes in red and white with voice prompt “pairing”.
2. Activate the Bluetooth in your device and hit “SOUNDPEATS TrueDot” on the Bluetooth list, once paired, the right earbud will hear a voice prompt “connected”.
3. The earbuds can remember previously paired devices. They would automatically connect to the last device they have paired before after being taken out from the case. If not, hit “SOUNDPEATS TrueDot” on the Bluetooth list and re-connect it.

Note:

1. If Left earphone doesn’t connect with Right one within 15 seconds when taking out both from charging case, it will be into standby status. And it will enter into pairing mode again by putting left earbud in charging case and waiting for 3s to be taken out again. (The left one will turn off automatically when in standby mode for 3 minutes)
2. If you want to replace the paired device while it’s connected, you can force the headset to go into pairing mode by long pressing the MFB of right earbud for 6s while the headset is off.

Factory Reset

(Try the following steps if you fail building connection between two earbuds, or between earbuds and device)

1. Clear the pairing record between the earbuds and all of your devices.
2. Hold and press the MFB of both earbuds for 10 seconds when in charging status, the LED indicator will flash red for 3 times if resetting successfully.

Charging

SOUNDPEATS TrueDot Bluetooth earphones are equipped with a compact and lightweight charging case which is not only a charging dock to charge the earphones, but also a carrying case. With a built-in rechargeable battery, the charging case can provide up to 3-4 times full charge for the earphones (both left and right).

Charging the headset

The earphones are partially charged at the factory. Please make sure they are fully charged before first use.

1. Put the earphones into corresponding charging slots, make sure the charging contractors are match.
2. The LED indicators on the earphones turn red to start charging.
3. The earphones are fully charged when LED indicators turn white and turn off after 1 minute.

Charging the case

When put the earbuds into the charging case, and then the earphone LED is not on, which means charging case battery is low, you should charge it in time.

1. Connect the charging port with any USB charging adapter(The current is no greater than 1A).
2. Please charge the earphones at least once every 3 months when not in use for a long time.

Warranty

We warrant this device 12 MONTHS from date of the original purchase for manufacturer
defects.
Email: support@soundpeatsaudio.com
Visit: www.soundpeatsaudio.com
Please scan the QR code or search the link below for detailed PDF manual :

https://soundpeatsaudio.com/downloads/

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

MANUFACTURER

Shenzhen SoundSOUL Information Technology Company Limited
Room 1308-1309, Building B, Huihai Square, Chuangye Road, Longhua District, Shenzhen, China. 518109
Email: support@soundpeatsaudio.com
Visit: www.soundpeatsaudio.com

FCC ID: 2AFTU-DD001
Model：SP120
MADE IN CHINA

References

• SOUNDPEATS Wireless Earbuds, Bluetooth Headphones, Speakers for Sound.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>