H-6313
ELECTRONIC STORAGE CABINET
1-800-295-5510
uline.com

TOOLS NEEDED

CAUTION! Some parts may have sharp edges. Take care when handling various pieces to avoid injury. For safety, wear work gloves when

PARTS

ASSEMBLE

| DESCRIPTION| QTY.

---|---|---
1| Back| 1
2| Right Side Panel| 1
3| Left Side Panel| 1
4| Shelf| 4
5| Top| 1
6| Bottom| 1
7| Door & Frame Assembly| 1
| #8-32 x 3/8″ Bolt (Not Shown)| 31
| #8-32 Nut (Not Shown)| 47

NOTE: Before assembly, to avoid being locked out of cabinet, remove the key for manual entry from the battery compartment on the back of the electronic lock.
ASSEMBLING CABINET

1. Place the back (1) on a protected surface. The bottom flange should face upward.

2. Attach the left side (3) and right side (2) to the back by placing flange around the back and bolting the back and sides together with seven bolts and nuts on each side. Be sure that the lances on all shelf adjustment strips point in the same direction. (See Figure 1)
   NOTE: Do not use the bottom hole on each side.
   

3. To help hold the sides in position, insert one shelf (4) into the approximate center of the unit, inserting the shelf edges into the lances on all four shelf adjustment strips. Be sure the channeled edge of the shelf is toward the cabinet front. (See Figure 2)
   

4. Locate top (5), which has the holes along the perimeter. Place top, with two holes toward front, under flanges at top of sides. Secure with three bolts along each side and five in back. (See Figure 3)
   

5. Place door and frame assembly (7) over body. (See Figure 4)
   NOTE: If having issues with doors aligning, it may be due to cabinet not sitting level. Use included nut driver to adjust leveling feet in bottom front two corners. Nut driver should  insert through inside of cabinet down into feet and adjust as needed.
   

6. Bolt sides to frame.
   

7. Place the bottom (6) in lowest notch of shelf adjusting strips so that the flange with two holes faces the front and is over the flange of the frame sill. Push out on side wall to enable bottom to slide into position. (See Figure 5)

8. Bolt bottom to frame sill.

9. Using a rubber mallet, place adjustable shelves in desired position with channeled edge toward front and press end and back flanges into notches of shelf adjusting strips.

10. Set the unit upright and insert the remaining shelves as desired. (See Figure 6)
    

11. Tighten all hardware.

ELECTRONIC LOCK INSTRUCTIONS

FRONT

GETTING STARTED

1. The battery compartment is located on the back of the electronic lock. To insert batteries, lift up on the compression tab at the bottom of the compartment.
   NOTE: The key for manual entry is located within the battery compartment. Keep this key in case of battery failure.

BACK
ENTERING SECURITY CODE

1. There are two preset codes, a personal and an administrator. The factory presets are:
   Personal (Pass 1): 1 2 3 4
   Administrator (Pass 2): 1 2 3 4 5 6

2. Press # key. Display will read “­­­­­­­­.”

3. Enter the code and press the # key.
   Once confirmed, display will read OPEN.

4. To conceal code, press after entering # key and before entering code. To disable concealment, press twice.
   NOTE: An alarm will sound if an incorrect code is entered three times. Alarm will sound for one minute, or until correct code is entered.

SETTING DATE AND TIME
NOTE: Date is displayed as year/month/day. There is a circular display of days of the week in the top right corner. Below that is the military time. (See Figure 7)

1. Press *. Enter last two digits of the year. Enter two digits of the month. Enter two digits of the day.
2. Enter day of week; i.e., Monday = 1, Sunday = 7.
3. Next, enter hour and minute as military time (AM hours 01-12, PM hours 13-24).
   

KEY ENTRY

1. The key slot is located underneath the cover, next to the handle. Remove cover by prying off from bottom.
2. Insert key into lock and turn counterclockwise.
3. While key is inserted, turn handle clockwise to release lock.

CHANGING SECURITY CODE

1. Open door with the current desired code to change (either personal or administrator).
2. With display reading OPEN, press *. Display will read “­­­­­­­­.”
3. Enter new code and press #. Display will read IN. Code is now changed.

RESETTING PERSONAL CODE IF LOST OR FORGOTTEN

1. Open cabinet using key.
2. When cabinet is open, personal code can be changed by pushing red button on top left side of lock.
3. After red button is pushed, enter new code and press # again.

RETRIEVE OPEN DOOR RECORDS

1. Press #, enter code, press #. Display will read OPEN. Then press 0.
2. Display will cycle through date, time, and password used (Pass 1 or Pass 2) on most recent opening. Press 0 to scroll back through records.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>