Pansonic Wall Mount Bracket Instruction Manual
- June 7, 2024
- Pansonic
Table of Contents
Operating Instructions
Included Installation Instructions
Wall Mount Bracket
Model No. WV-Q122A
The camera in the illustration is separately sold.
Before attempting to connect or operate this product, please read these
instructions carefully and save this manual for future use.
The model number is abbreviated in some descriptions in this manual.
Preface
This mount bracket is used for installing the color CCTV camera and network
camera on a wall.
Refer to the catalog or operating instructions of the camera for further
information about the compatible models.
Precautions
Refer installation work to the dealer.
Installation work requires technique and experience.
Failure to observe this may cause fire, electric shock, injury, or damage to
the product.
Be sure to consult the dealer.
Avoid installing this bracket in the locations where salt damage occurs or
corrosive gas is produced.
Otherwise, the mounting portions will deteriorate and accidents such as a fall
of this product may occur.
The screws and bolts must be tightened to the specified torque.
Loosening of mounting screws or bolts may cause a fall of the product
resulting in injury or accidents.
Do not use this bracket except with suitable cameras
Failure to observe this may cause a drop resulting in injury.
Select an installation area that can support the total weight.
Selecting an inappropriate installation surface may cause this product to fall
down or topple over, resulting in injury or accidents.
Installation work shall be started after sufficient reinforcement.
Do not rub the edges of metal parts with your hand.
Strong rubbing may cause injury.
Periodic inspections shall be conducted.
Rust on the metal parts or screws may cause a fall of the product resulting in
injury or accidents.
Consult the dealer for the inspections.
The measures of protection against a fall of this product shall be taken.
Failure to observe this may cause a drop resulting in injury or accidents.
Be sure to install the safety wire.
Do not install this product in locations subject to vibration.
Loosening of mounting screws or bolts may cause a fall of the product
resulting in injury or accidents.
Do not strike or give a strong shock to this product.
Failure to observe this may cause fire or injury.
Install this product in a location high enough to avoid people and objects
from bumping the product.
Failure to observe this may cause injury.
Do not hang down from this product or use this prod- uct as a pedestal.
Failure to observe this may cause a drop resulting in accidents.
Do not install the product in a windy place.
Installation of the product in wind with a speed of 40 m/s or more may cause a
drop resulting in accidents.
The measures of protection against snowfall shall be taken.
The weight of snow may cause a fall of the product resulting in injury or
accidents.
Protect the product against snowfall by installing it under eaves.
Precautions for installation
Panasonic assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation.
The installation should comply with the local electrical code.
Before start, the installation/connection, check and prepare the required
devices and cables. Before starting the connection, turn the power of the
devices including the camera and the PC off.
Refer installation work to the dealer. Failure to observe this may cause
fire, electric shock, injury, or damage to the product.
Power supply
Use a power supply device equipped with the ON-OFF switch for servicing. When
the power cord of the product is connected to the power supply device, the
power will be
supplied to the product. When the product is supplied, the product will
perform panning, tilting, zooming, and focusing.
Before cleaning the product, make sure that the power cable is not connected
to the main power supply.
Installation area for this product
Consult the dealer about the installation area to select a strong wall area.
- Screws used for installing this product on a wall are not supplied. Prepare them according to the material and strength of the area where the product is to be installed. Recommended screw: M8 x 4 pcs. Minimum pull-out strength (per 1 pcs.): 823 N {185 lbf}
- Do not mount the product on a plasterboard or a wooden section because they are too weak. If the product is unavoidably mounted on such a section, the section shall be
sufficiently reinforced.
Mounting method for this product
This product is designed to be used as a pendant mount camera. If the product
is mounted on a desktop or at a slant, it may not work correctly and its
lifetime may be shortened.
Protection from lightning
When cables are used outdoors, there is a chance that they may be affected by
lightning. In this case, install a lightning arrester just before where the
cables connect to the camera.
Do not place this product in the following places:
- Locations where a chemical agent is used such as a swimming pool
- Locations subject to moisture or oil smoke such as a kitchen
- Locations that have a specific environment that is sub- get to an inflammable atmosphere or solvents
- Locations where radiation, x-ray, intense radio wave, or strong magnetism is produced
- Locations where corrosive gas is produced, locations where it may be damaged by briny air such as seashores
- Locations where the temperature is not within the specified range (–50 °C to +55 °C {–58 °F to 131 °F})
- Locations subject to vibrations, such as on vehicles, marine vessels, or above product lines (This product is not designed for vehicle use.)
- Locations subject to condensation as the result of severe changes in temperature (In the case of installing the product in such locations, the dome cover may become foggy or condensation may be caused on the cover.)
Screw tightening
- The screws and bolts must be tightened with an appropriate tightening torque according to the material and strength of the installation area.
- Do not use an impact driver. The use of an impact driver may damage the screws or cause tightening excessively.
- When a screw is tightened, make the screw at a right angle to the surface. After tightening the screws or bolts, perform checks to ensure that the tightening is sufficient enough so that there is no movement or looseness.
The protection cover attached to the camera unit shall be removed after
completion of the installation. (rain wash coating model)
Make sure to remove this product if it will no longer be used.
Take notice of humidity.
Install this product when the humidity is low. If this product is installed
during rainfall or at high humidity, the inside may be exposed to moisture and
the dome cover may become foggy.
Matters you should know at installation work
The compatibility of devices are restricted. Before connections, check the
ratings and dimensions of the devices to be used.
Refer to “Panasonic CCTV System General Catalog” or contact your dealer for
further information.
Major operating controls
Installations/Connections
Be sure to read “Precautions” and “Precautions for installation” before
installation.
Read the operating instructions for the camera to be installed as well. The
Operating Instructions mainly describe for installing a network camera.
The basic flow of the installation operation is the same as the one for the
color CCTV camera.
The flow of how to install the wall mount bracket is described as follows.
-
How to detach the housing base (☞ 6 pages)
Remove the housing base and attachment pipe from the camera body. -
Attaching the mount bracket (☞ 8 pages)
■ When laying cables through the cable access hole (front) (☞ 8 pages)
■ When laying cables after drilling a hole through the wall (☞ 10 pages) -
Mounting of the camera body on the mount bracket (☞ 12 pages)
Secure the camera body to the housing base.
How to detach the housing base
Before attaching the camera to the wall mount bracket, detach the housing base
and attachment pipe from the camera so that installation and connections can
be performed.
Step 1
Remove the fixing screws (3 pcs.*) that are securing the housing base and the
camera.
The removed screws will be required when attaching the camera to the housing
base. Use caution not to lose these screws.
- Special screw (fixing screw): These screws are hexagon screws. Use an M5 hexagon wrench.
There are 2 types of wrenches to be used; one is hexagonal wrench “for M5” (WV-SW598) and the other is hexagonal wrench “for M6”.
Refer to the Operating Instructions of the camera for the wrench to be used, which depends on models.
IMPORTANT:
- The protection cover attached to the camera unit shall be removed after completion of the installation. (Only for rain-wash coating model)
Step 2
To separate the housing base from the camera, turn the housing base to the
direction of the arrow as illustrated. (Refer to the illustration in Step 1.)
Step 3
Remove the attachment pipe from the upper base by loosening 4 screws.
Go to “■ When laying cables through the cable access hole (front)” (☞ 8 pages) or “■ When laying cables after drilling a hole through the wall” (☞ 10 pages).
Attaching the mount bracket
The installation of the wall mount bracket is roughly divided into 2 methods.
Refer to the applicable description.
- When laying cables through the cable access hole (front) (☞ 8 pages)
- When laying cables after drilling a hole through the wall (☞ 10 pages)
When laying cables through the cable access hole (front)
Step 1
Decide the mounting position and drill a hole in the wall.
Procure 4 pieces of M8 screws and anchors to secure the this bracket on the
wall.
All screws and anchors shall be stainless steel. The hole diameter shall be
decided in accordance with the screws and anchors to be used.
A hole on the wall with a diameter of 30 mm {ø1-3/16 inches} or less can be
hidden with this bracket.
Step 2
Make a slit in the center of the cable cap (accessory) with a cutter.
Step 3
Pass the cables from the housing base through this bracket, and mount the
cable cap that was slit in Step 2 on the cable access hole (front).
Secure the housing base to the wall mount bracket.
Attach the housing base to this bracket using the 4 screws* supplied with the
camera. The “REAR” mark of the housing base shall be directed to the wire hook
section.
*
Refer to the Operating Instructions of the camera for the screws and the
wrenches to be used, which depends on models.
For the case of the camera with M5 screws being used (WV-SW598): Use the
screws supplied with the camera and a hexagonal wrench “for M5”.
For the case of the camera with M6 screws being used:
Use the screws supplied with the bracket and a hexagonal wrench “for M6”.
(Recommended tightening torque (for common use in M5 and M6): 2.45 N.m {1.81
lbf·ft})
Step 4
Seal the slit of the cable cap for the prevention of water leakage.
Step 5
Mount another cable cap (accessory) on the rear plate.
Step 6
Mount the mount bracket on the wall with 4 screws (M8: locally procured).
Minimum pull-out strength: 823 N {185 lbf}/per 1 pc.
Step 7
Connect the cables to the camera.
Connect the cables from the housing base with the cables on the wall.
After cable connection, seal the connecting portion with waterproof tape
(locally procured).
IMPORTANT:
- These operations shall be performed in accordance with the electric installation engineering standards.
Perform sealing to prevent the connecting portion of the cables from being exposed.
Moisture may come into the camera from the gap among the cables and cause the inside of the dome cover to become foggy.
Go to “[3] Mounting of the camera body on the mount bracket” (☞ 12 pages).
When laying cables after drilling a hole through the wall
Step 1
Decide the mounting position, and drill a hole for a screw or an anchor and a
hole for cable installation in the wall.
Procure 4 pieces of M8 screws and anchors to secure the this bracket on the
wall.
All screws and anchors shall be stainless steel. The hole diameter shall be
decided in accordance with the screws and anchors to be used.
A hole on the wall with a diameter of 30 mm {ø 1-3/16 inches} or less for a
screw or an anchor can be hidden with this bracket.
Step 2
Mount the cable cap (accessory) on the cable access hole (front).
Step 3
Make a slit in the center of another cable cap (accessory) with a cutter.
Step 4
Remove the 4 screws from the rear side of the bracket, remove the plate, and
mount the cable cap that was slit in
Step 5
Lay the cables from the housing base via this blanket into the slit cable cap.
Secure the housing base to the wall mount bracket.
Attach the housing base to the mount bracket using the 4 screws*.
The “REAR” mark of the housing base shall be directed to the wire hook
section.
- Refer to the Operating Instructions of the camera for the screws and the wrenches to be used, which depends on models.
For the case of the camera with M5 screws being used (WV-SW598):
Use the screws supplied with the camera and a hexagonal wrench “for M5”.
For the case of the camera with M6 screws being used:
Use the screws supplied with the bracket and a hexagonal wrench “for M6”.
(Recommended tightening torque (for common use in M5 and M6): 2.45 N·m {1.81 lbf·ft})
Secure the plate with the 4 screws removed in Step 4 on the rear side of the bracket, and seal the slit of the cable cap.
(Recommended tightening torque: 0.78 N·m {0.58 lbf·ft})
Step 6
Connect the cables to the camera.
Connect the cables from the housing base with the cables coming through the
wall.
After cable connection, seal the connecting portion with waterproof tape
(locally procured).
IMPORTANT:
- These operations shall be performed in accordance with the electric installation engineering standards.
Perform sealing to prevent the connecting portion of the cables from being exposed.
Moisture may come into the camera from the gap among the cables and cause the inside of the dome cover to become foggy.
Step 7
Mount this bracket on the wall with 4 screws (M8: locally procured).
Minimum pull-out strength: 823 N {185 lbf}/per 1 pc.
Go to “[3] Mounting of the camera body on the mount bracket” (☞ 12 page).
Mounting of the camera body on the mount bracket
Step 1
For the case of color CCTV camera, peel off the seal on the top of the camera,
and specify the communication method and unit address using the DIP switches.
Refer to the Operating Instructions of the color CCTV camera for how to set
the DIP switch.
Put the seal back after specifying them.
Communication method: specifying with SW2 Unit address: specifying with SW1
Step 2
Align the flat spring with the START position.
If not, rotate the plate on the top of the camera clockwise to align it with
the “START” position.
For the case of network camera
For the case of color CCTV camera
Step 3
Engage the safety wire with the wire hook section.
Step 4
When attaching the camera to the housing base, the positioning pin shall be on
the “REAR” side.
Make sure that the camera is securely attached to the mount bracket by turning
the bracket counterclockwise (seen from below).
Tighten them firmly with the 3 screws* that have been removed in Step 1.
- Special screw (fixing screw): These screws are hexagon screws. Use a hexagon wrench.
There are 2 types of wrenches to be used; one is hexagonal wrench “for M5” (WV-SW598) and the other is hexagonal wrench “for M6”. Refer
to the Operating Instructions of the camera for the wrench to be used, which depends on models.
(Recommended tightening torque (for common use in M5 and M6): 2.45 N·m {1.81 lbf·ft})
- The illustration above is provided for describing the top of the camera, and therefore, this bracket is omitted.
Step 5
Mount the front and rear sun shields, and then remove the protective cover.
Refer to the Operating Instructions of the camera for further information.
Removal of the protection cover is described only for rain wash coating model.
Specifications
Ambient operating temperature: –50 °C to +55 °C {–58 °F to 131 °F}
Dimensions: 120 mm (W) x 220 mm (H) x 269 mm (D)
{4-23/32 inches (W) x 8-21/32 inches (H) x 10-19/32 inches (D)}
Mass: Approx. 2 kg {4.42 lbs}
Finish: Aluminum die-cast (coating color: fine silver (901))
Weight and dimensions indicated are approximate.
Specifications are subject to change without notice.
Standard accessories
Operating Instructions (this document) ………………………………………. 1 set
The following are for installation
Cable cap …………………………………………………………………………… 2 pcs.
Camera mounting screw (Hexagon screw (M6)) ………………………… 4 pcs.
For U.S. and Canada:
Panasonic System Communications Company of North America, Unit of Panasonic
Corporation of North America
www.panasonic.com/business/
For customer support, call 1.800.528.6747
Three Panasonic Way, Secaucus, New Jersey 07094 U.S.A.
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada
(905)624-5010
www.panasonic.ca
For Europe and other countries:
Panasonic Corporation
http://panasonic.net
Importer’s name and address to follow EU rules:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany
© Panasonic System Networks Co., Ltd. 2013
Ns0913-0
PGQX1409ZA
Printed in China