MOUNTUP MU8003 Premium Triple Monitor Stand Instruction Manual

June 14, 2024
MOUNTUP

MOUNTUP logo MU8003 Premium Triple Monitor Stand
Instruction Manual

MU8003 Premium Triple Monitor Stand

MOUNTUP MU8003 Premium Triple Monitor StandMOUNTUP MU8003 Premium Triple Monitor Stand -
icon

If you have any questions, please feel free to contact Customer Service via Amazon before returning.
WARNING!
If you have any confusion or are not quite sure about the installation, please do not hesitate to ask for our help.
Before assembly, please check and make sure all necessary accessories are included and undamaged. Improper installation (including not properly following the indicated instructions or cautions /attentions), such as using the product for monitors over its load capacity or for any purpose not explicitly speciffed, may cause damage or serious injury. We would not be liable for any damage or injury caused by improper mounting or inappropriate use. The kit contains small items that could be choking hazards if swallowed. Please keep them OUT OF REACH OF CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS

MOUNTUP MU8003 Premium Triple Monitor Stand - PACKAGE
CONTENTS DO NOT EXCEED WEIGHT CAPACITY.

ASSEMBLY STEPS

STEP 1 : Clamp Installation OR Grommet Base Installation
Firstly mount Bake (C) to Pole (B) using Bolts (O). Tighten them using 4mm Allen Key (R).MOUNTUP MU8003 Premium Triple Monitor Stand - Firstly mount
Bace OPTION A: Clamp Installation
Mount Bracket (E) to Base (C) with Bolts (N). Bolts could be tightened by the 4mm Allen Key (R). Apply pads (P) to the bottom of Base (C) to avoid desk scratches.MOUNTUP MU8003 Premium Triple Monitor Stand - Clamp
InstallationAttach Clamp (F) to Bracket (E) with Bolts (N) and 4mm Allen Key (R). Adjust the Clamp width to fit with desk.MOUNTUP MU8003 Premium Triple Monitor Stand - Attach
Clamp STEP 1 : (Continued)
Secure stand to desktop by tightening Clamp (F) or by Allen key (T). Attach Base Support Cover (E) to Bracket (E). MOUNTUP MU8003 Premium Triple Monitor
Stand - BracketOPTION B: Grommet Base Installation
Place Carriage Bolt (H) through the center of Grommet Base (J).
Mount Grommet Base to Base (C) bottom with Bolts (N) and tighten them by 4mm Allen Key (R).
Apply pads (P) to the bottom of Base (C) to avoid desk scratches.MOUNTUP
MU8003 Premium Triple Monitor Stand - Grommet BaseRun Carriage Bolt (H) through grommet hole on desktop. Attach Support Plate (I) and Wingnut (K). At last, tighten Wingnut (K).MOUNTUP
MU8003 Premium Triple Monitor Stand - Support Plate STEP 2 : Arm Installation
Install the middle head (Q) wire clip(M) and swivel arm (A) to the pole (B). Fasten the bolt with supplied 6mm Allen key (T)MOUNTUP MU8003 Premium Triple
Monitor Stand - middle head WARNING:
For your safety, do not move the stand of your desk!
STEP 3 : Attach Monitor
OPTION A: Flat Back Monitor
Attach the VESA plate (F) to the back of monitor and secure it by using a 6 mm Allen Key (Q) to tighten screws (M-A ) . Do not tighten the screws excessively or your monitor might be damaged.MOUNTUP MU8003 Premium Triple Monitor
Stand - Flat Back Monitor OPTION B: Curved / Recessed Back Monitor
Attach the VESA plate (F) to the back of monitor and secure it by using a 6 mm Allen Key (Q) to tighten screws (M-B) along with spacers (M-C). Do not tighten the screws excessively or your monitor might be damaged.MOUNTUP MU8003
Premium Triple Monitor Stand - monitor might STEP 4 : Hang Monitor
Slide the monitors onto the head of swivel arm. Install the security bolt (L). Make sure the security bolt is tightened before you rotate the monitor.MOUNTUP MU8003 Premium Triple Monitor Stand - Hang
Monitor Important Notice:
The pressure of the gas spring is initially set at the lowest value. So when the monitor is hung on, make sure you hold it with both hands and DO NOT let it go down suddenly.
Guideline to adjust monitor tilting angle.MOUNTUP MU8003 Premium Triple
Monitor Stand - monitor tilting angle Problem:
If monitor faces downMOUNTUP MU8003 Premium Triple Monitor Stand - tilting
bolt Solution:

  1. Loosen the tilting bolt.
  2. Hold the bottom of monitor with one hand and adjust to determine your desired tilt angle.
  3. Retighten the tilting bolt towards ” +” to fix the angle.

STEP 5 : Adjust Gas Spring Tension
For intended functioning of the mount, you will need to adjust the tension of Arm (A) in accordance with your monitor weight by 6mm Allen Key (T).MOUNTUP MU8003 Premium Triple Monitor Stand - Gas Spring
Tension Note1:
Be sure to keep the arm in horizontal position during adjustment. Or else it would be difficult to adjust the mount or damage the mount. Situation 1: Arm falls down
Upper Arm with monitor falls down and fails to stay where intended.
Solution:
Turn the inside screw counterclockwise(“+”direction) to increase gas spring tension until the arm can stay as intended. Situation 2: Arm rises up/can’t be pressed down
Upper Arm with monitor rises up automatically or can’t be pressed down and fails to stay where intended.
Solution:
Turn the inside screw clockwise(“-”direction) to decrease gas spring tension until the arm can stay as intended.
Note2:
For how many circles the screw should be turned, please refer to the table below.

Monitor Weight| 2.2 lbs| 6.6 lbs| 8.8 lbs| 15.4 lbs| 22 lbs| 28.7 lbs| 30.9 lbs
---|---|---|---|---|---|---|---
| (1 k9)| (3 kg)| (4 kg)| (7 kg)| (10 kg)| (13 kg)| (14 kg)
Circles (AT LEAST)| min| 5| 7| 10| 13| 16| 20

STEP 6 : Cable Management

Remove Cable Cover
Remove bottom plastic covers from arm as shown in diagram.
Do not need to take much effort to pull the ends of the cable cover away from the arm.MOUNTUP MU8003 Premium Triple Monitor Stand - Remove Cable
Cover Attach Cable Cover
Run cables from monitor through bottom of arm. Reattach plastic covers as shown in diagram.MOUNTUP MU8003 Premium Triple Monitor Stand - Attach Cable
Cover

Adjust as Desired

Adjust monitor position and rotation.
Store Allen keys (R, S) in wire clip (G) for future use. MOUNTUP MU8003
Premium Triple Monitor Stand - Adjust as DesiredNote: To ensure stability, the tightness of the rotating axis has been presented, so it would be kind of difficult to rotate the VESA plate.
Suggestion: Please attach the monitor first, then hold the two sides of it with both hands, and rotate vigorously. If that doesn’t work out, please do not hesitate to ask for our help.

Product Dimensions

MOUNTUP MU8003 Premium Triple Monitor Stand - Product
Dimensions

CAUTION AND MAINTENANCE:

  • Don’t allow children to climb, stand, hang, or play on any part of monitor or stand.
  • This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
  • Check that the bracket is secure and safe to use at regular intervals (at least every three months).MOUNTUP logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals